2. Home
  3. Domestic appliances
  4. Small kitchen appliances
  5. Mincers
  6. Hanna
  7. MG438
MG438

Hanna MG438 User manual

  • Hello! I've read the instruction manual for the Nutronic Meat Grinder MG438. This document provides detailed instructions on how to assemble the device, use the meat mincing, kubbe, sausage, salad maker and cookie making attachments, and also includes important instructions for cleaning and maintenance. I'm ready to answer your questions about the meat grinder and its features.
  • Can I grind bones or nuts?
    How long can I continuously run the meat grinder?
    What should I do if the grinder jams?
    What should I do after using
-1-
INSTRUCTION MANUAL
MEAT GRINDER
Model：MG438
（120V/60Hz，450W，Locked power 1300W，KB=5min）
-2-
Catalog
DESCRIPTION............................................................................................................................................................. 3
IMPORTANT SAFEGUARDS.......................................................................................................................................4
FOR THE FIRST TIME................................................................................................................................................ 5
INSTRUCTION FOR USE............................................................................................................................................6
ASSEMBLING.............................................................................................................................................................6
MINCING MEAT........................................................................................................................................................ 7
REVERSE FUNCTION............................................................................................................................................7
MAKING KUBBE........................................................................................................................................................8
MAKING SAUSAGE...................................................................................................................................................9
SALAD MAKER FUNCTION.................................................................................................................................. 10
INSERT / REMOVE THE SALAD MAKER........................................................................................................... 10
MAKING COOKIES..................................................................................................................................................10
DISASSEMBLING...................................................................................................................................................... 12
CLEANING................................................................................................................................................................. 13
CORRECT DISPOSAL OF THIS PRODUCT..................................................................................................... 13
-3-
DESCRIPTION
1. Food pusher
11-12.Kebbe attachment set
2. Hopper plate
13.Locking knob
3. Head Tube
14.Motor housing
4. Feed screw
15. ON/OFF switch
5.Cutting blade
16-17. Cookie Maker attachments set
6. Cutting plate(Coarse)
18.Tube
7.Fixing ring
19.Pusher
8.Cutting plate(Medium)
20.French frier cutter
9.Cutting plate(Fine)
21.Masher
10.Sausage
22.Slicer
-4-
IMPORTANT SAFEGUARDS
Household use only. Do not use for industrial purpose.
Unplug from outlet when assembling and disassembling the unit.
Close supervision is necessary
Children should be supervised to ensure that they do not play with the appliance.
When carrying the unit be sure to hold the motor housing with both hands. Do not
carry the unit by holding only the hopper plate or head.
Do not fix the cutting blade and cutting plate when using kebbe attachment.
Never feed food by hand. Always use food pusher.
Do not grind hard food such as bones, nuts, etc.
Do not grind ginger and other materials with hard fiber.
Continuous running of meat grinder should be not more than 5 minutes.
Reverse function is prohibited while the appliance is operating, wait at least one
minute until grinder has come to a complete stop，otherwise it may cause an
abnormal noise, vibration or a transitory electric spark in the appliance. It could
result easily damage to appliance and make a user frightened.
After use, there would be a little food left in the grinder head. This is normal.
There might be a bit of black metal powder adhering to the food ground in the
end. Please pick them out and throw away, do not eat them.
To avoid jamming, do not force to operate the unit with excessive pressure.
When the circuit breaker activates, do not switch on.
Never try to replace the parts and repair the unit by yourself.
Children or handicapped should be supervised to ensure that they do not play with
the appliance.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
-5-
FOR THE FIRST TIME
Check that voltage indicated on the rating label corresponds the mains voltage in
your home.
Wash all parts (except body) in warm soapy water.
Before plugging in, ensure the “ON/ OFF” switch is turned to “OFF” position.
-6-
INSTRUCTION FOR USE
ASSEMBLING
Press the fasten button，hold the head and insert it into the inlet(when inserting please pay
attention the head must be slanted as
per arrow indicated on the top, see fig.1),
then move the head anticlockwise so that
the head being fastened tightly .(fig.2)
Place the snake into the head, long end first,
and turn to feed the screw slightly until it is
set into the motor housing (fig.3).
Place the cutting blade onto the snake shaft
with the blade facing the front as illustrated
(fig.4).If it is not fitted properly, meat will
not be grinded.
Place the desired cutting plate next to the
cutting blade, fitting protrusions in the slot (fig.5).
Support or press the center of the cutting
plate with one finger then screw the fixing ring
tight with another hand (fig.6). Do not over
tighten.
Place the hopper plate on the head and fix it into
position.
Locate the unit on a firm place.
The air passage at the bottom and the side of the motor housing should be kept free
and not blocked.
-7-
MINCING MEAT
Cut all foods into pieces (Sinewless, boneless and fatless meat is recommended,
approximate size :20 mm x 20 mm x 60 mm) so that they fit easily into the
hopper opening.
Plug in and turn the “ON/OFF” switch to “ON” position.
Feed foods into the hopper plate. Use only the food pusher (fig.7).
After use switch the unit off and unplug it from the power supply.
REVERSE FUNCTION
In case of jamming switch the appliance off by pressing the “ON/ OFF” switch.
Waiting the grinder has come to a complete stop. Then,
press the “R” button.
-8-
MAKING KUBBE
Insert the worm shaft into the cutter housing, the
1. plastic end first.(fig.8)
2. Place the cone in the cutter housing.
3. Place the former on the cutter housing and screw
4. the ring on the cutter housing.(fig.9)
5. Attach the cutter housing to the motor unit.
6. Place the tray on the upright part of the cutter housing.
7. Now the appliance is ready for making kebbe.(fig.10)
8. Feed the prepared kebbe mixture through the kebbe maker.
9. Cut the continuous hollow cylinder into the desired lengths
and user as required.
Kebbe is a traditional Middle Eastern dish made primarily of
lamp and bulgur wheat which are minced together to form a paste the mixture is extruded
through the kebbe maker and cut into short lengths. The tubes can then be stuffed with a
minced meat mixture, the ends pinched together and then deep fried.
-9-
MAKING SAUSAGE
1. Mince the meat
Insert the worm shaft into the cutter housing , the plastic end first.(fig.11)
Place the separator in the cutter housing.
Place the sausage horn on the cutter housing and screw the ring on the cutter housing.
(Make sure the notches of the separator fit onto the projections of the mincer head.)
2. Attach the cutter housing to the motor unit.
3. Place the tray on the upright part of the cutter housing.
4. Now the appliance is ready for making sausages.
Put the ingredients in the tray. Use the pusher to gently push the meat into the cutter
housing.
Put the sausage skin in lukewarm water for 10 minutes. Then slide the wet skin onto the
sausage horn. Push the (seasoned) minced meat into the cutter housing. If the skin gets
stuck onto the sausage horn, wet it with some water.
-10 -
SALAD MAKER FUNCTION
1. Pusher
2. Salad maker tube
3. Cutting roll - Slicing
4. Cutting roll - Shredding
5. Cutting roll - Mashing
INSERT / REMOVE THE SALAD MAKER
1. Hold the salad tube tilted slightly to the right and insert it into the motor unit,
rotate the salad tube turn to left in a quarter until the tube locked on product. Rotate it
in reverse way can release the salad tube accordingly.
2.
Ch
oo
se the cutting rolls as you
need and insert it onto the salad tube as follow pic.
3.Put the vegetable onto salad maker tube to process the cutting, use pusher to push
the food during using, do not push the food by hand directly.
MAKING COOKIES
Before making cookies, knead the dough as your favor
-11 -
Assemble the cookie maker attachment as per following fig.
Choose the shape that you want.
Put the dough on food tray, use pusher to push the dough into feeding tube.
-12 -
DISASSEMBLING
Make sure that the motor has stopped completely.
Disconnect the plug from the power outlet.
Disassemble by reversing the steps from 6-1 pictures.
If the fixing ring is not easily removed by hands, please use tools（fig.12）.
To remove the cutting plate easily, place a screwdriver between the cutting plate
and the head as illustrated and lift it up (fig.13).
-13 -
CLEANING
Remove meat, etc. Wash each part in warm soapy water.
A bleaching solution containing chlorine will discolor aluminum surfaces.
Do not immerse the motor housing in water, but only wipe it with a damp cloth.
Thinners and petrol will crack or change the color of the unit.
Wipe all the cutting parts by vegetable oil -wet cloth.
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with other household
wastes throughout the US. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of
material resources. To return your used device, please use the return and collection
systems or contact the retailer where the product was purchased. They can take this
product for environmental safe recycling.
Manufacturer: Nutronic
Address: Floor 3 No.9 Building Chaoguang Road Ronggui, Shunde, FoshanCity
Guangdong, China
Made In China
/