Powerplus POWLI20301 Owner's manual

Brand: Powerplus

Model: POWLI20301

Type: Owner's manual

Powerplus POWLI20301 is a versatile LED floodlight with a motion sensor, suitable for both indoor and outdoor use, such as job sites, gardens, studios, and workshops. Its sturdy construction, IP65 waterproof rating, and long lifespan of over 30,000 hours ensure reliable operation in various conditions. The floodlight offers adjustable settings for time (3 seconds to 5 minutes), LUX (10 lux to 1000 lux), and sensitivity (1 meter to 6 meters), allowing you to customize its operation based on your specific needs.

POWLI20301 EN

LED FLOODLIGHT 30W WITH SENSOR

POWLI20301

1 DOMAIN OF USE

Outdoor or indoor usage such as jobsite, garden, studio and workshop.

WARNING! Read this manual and general safety instructions

carefully before using the appliance, for your own safety. Your power

tool should only be passed on together with these instructions.

2 WARNING

▪ This Product is Class I and must be Earthed.

▪ Always switch off mains supply before fitting.

▪ Replace any broken or damaged glass as soon as possible.

▪ Ensure all seals are intact and operational after fitting or maintenance.

▪ Do not touch the lamp in use or just after use as there is a risk of being burnt.

▪ Do not cover it with paper or cloth.

▪ Take off from flammable materials.

▪ Do not wash the lamp.

▪ Do not use the lamp where the ambient temperature is over 45°C and less than -

25°C.

▪ Keep with a secure distance, the light could cause damage to your eyes.

▪ To move or placed, the product must face up to avoid damage to the sensor.

3 ASSEMBLY

▪ Find a suitable location to install this product.

▪ Prepare the mains wiring.

▪ Use the mounting bracket to mark the hole centres for fixing.

▪ Drill holes suitable to accept wall plugs. Insert wall plugs.

▪ Ensure mounting bracket.

▪ Terminate wiring. (Fig. 1)

▪ Replace all covers.

▪ Fit the floodlight to the mounting bracket with the screws,

▪ Check seals, gaskets and cable gland operation before testing the luminaire.

▪ Turn on power supply and test luminaire.

4 SETTING THE LIGHT SYSTEM

4.1 TIME adjustment

The TIME adjustment controls how long the floodlight will

stay on after the motion has been detected.

You can adjust time from 3 seconds to 5 minutes.

4.2 LUX adjustment

POWLI20301 EN

The LUX adjustment determines at what light level the

lighting system will start operating.

You can adjust LUX from 10lux to 1000lux.

4.3 SENS. adjustment

The sensitivity adjustment may be adjusted to compensate

for seasonal variations in temperature and to reduce

unwanted triggering. Detecting distance can be adjusted

from 1m to 6m.

5 TECHNICAL DATA

Type

POWLI20301

Power

30W

Voltage/frequency

100–240V ~ 50/60Hz

Floodlight facade material

tempered glass

Waterproof protection grade

IP65

life-span

>30.000 hours

Lumen

2250

Color temperature

6500K

Beam angle

100°

Detection angle

90°

Net weight

1,4kg

Dimensions

26x6x25,5cm

6 POSSIBLE PROBLEMS

▪ Ventilators, such as the discharge from a vapor cap or dryer (hot air movement) can

cause the lamp to switch on when it is not required to do so.

▪ Passing cars (warm engines) can also cause your lamp to switch on.

▪ Nearby trees and bushes, sudden changes in temperature and gusts of wind can

also cause the lamp to switch on.

▪ If the lamp has been placed under a roof or under trees, then the lamp can also burn

during daylight hours.

▪ If your lamp does not work then the bulb or fuse could be defective or there may have

been a failure in the electrical circuit.

▪ If the temperature difference between the object to be detected and surrounding area

is too small (in the summer for example), then your lamp will react later. The range of

detection is then 5 meters instead of 7 meters for example.

POWLI20301 EN

▪ If the electromagnetic interferences are strong enough (4KV electrostatic discharge,

3V/m electromagnetic HF-field and 500V electrical fast transient burst), then the lamp

may turn on unintentionally.

7 MAINTENANCE

▪ This product has no user serviceable parts.

▪ Clean with a damp cloth and dry with a lint free cloth or kitchen towel.

8 IMPORTANT INFORMATION

It is recommend that luminaires installed and fitted by a qualified electrician ensuring the

installation complies to the current building regulations. These products are designed for

connection to a 100-240V supply.

Any broken or damaged parts should be replaced as soon as possible.

9 ENVIRONMENT

Should your appliance need replacement after extended use, do not

discard it with the household rubbish but dispose of it in an environmentally

safe way.

Waste produced by electrical machine items should not be handled like

normal household rubbish. Please recycle where recycle facilities exist.

Check with your Local Authority or retailer for recycling advice.

Powerplus POWLI20301 Owner's manual

Powerplus POWLI20301 Owner's manual

Powerplus POWLI20301 Owner's manual

Related papers

Other documents