Avtech RMA-FS2-SEN User manual

Type
User manual

Avtech RMA-FS2-SEN is a flood sensor that can be used to detect the presence of liquid on a flat surface. It has two adjustable-height contacts that can be set to trip the sensor when liquid collects underneath the housing. The sensor comes with a 25' low-voltage 2-wire cable that can be used to connect it to a Room Alert or Wireless Sensor Hub. The sensor is powered by a 9V alkaline battery and has a maximum extendable length of 900'.

Avtech RMA-FS2-SEN is a flood sensor that can be used to detect the presence of liquid on a flat surface. It has two adjustable-height contacts that can be set to trip the sensor when liquid collects underneath the housing. The sensor comes with a 25' low-voltage 2-wire cable that can be used to connect it to a Room Alert or Wireless Sensor Hub. The sensor is powered by a 9V alkaline battery and has a maximum extendable length of 900'.

Installation Note
Temperature & Environment Monitoring... Made Easy!
Flood Sensor - Spot
AVTECH
AVTECH’s Flood Sensor - Spot monitors the

When liquid collects underneath the blue
housing, it bridges the 2 adjustable-height



Self-adhesive feet on the bottom of the housing
allow you to fasten the sensor to trouble-spots
and also provide a gap to admit water to the

Flood Sensor - Spot Package Contents
One (1) Flood Sensor - Spot with 25' low-voltage 2-wire cable attached
One (1) 9V alkaline battery
Flood Sensor - Spot
FootLiquidFoot
Housing
Surface
Contacts
1"

Install Your Flood Sensor - Spot

Step 1: Adjust the height of the contacts if necessary.










Page 2
Flood Sensor - Spot (RMA-FS2-SEN)
Step 2: Connect the battery.
Your Flood Sensor - Spot comes with a 9V alkaline
battery inserted into the retainer clip under the

Push the snap connector completely on to



Use only alkaline batteries in your sensor, and

Flood Sensor - Spot gets activated often, you may

Step 3: Mount your Flood Sensor - Spot.
 
 You may simply rest the unit on its feet or remove the backing on the pads to stick it


form a seal, and water won’t reach the contacts until it’s risen up the sides or over the

Step 4: Connect your Flood Sensor - Spot to Room Alert.



Your sensor comes with one end of a 25' low-voltage 2-wire cable


 Separate and strip the leads on the free end of the speaker

 


 



Feet
Contacts
Snap
Connector
Retainer
Clip
Page 3
Flood Sensor - Spot (RMA-FS2-SEN)
Test Your Flood Sensor - Spot
Once you have inserted the battery and connected to Room Alert, you may easily test the

Sensor Features & Specications
Environment Condition Monitored Presence/absence of liquid
Type Of Sensor Switch
Normal State 
Alarm State Open (Liquid detected)
Power Supply 9V alkaline battery
Sensor Cable Type Low-voltage two-wire cable
 Yes
Length 25'
 900'
Compatible Products 

Page 4
Congure Your Switch Sensor
Congure Your Switch Sensor
Use Room Alert’s Built-In Web Interface
Navigate to
Settings
Sensors


 Scroll down to Switch Sensor Settings
 Find the switch sensor label that matches the port you connected your switch sensor

Sensor 1 Label; if you used the second, look for Sensor 2 Label
 Sensor X Label, you may leave the default, “Switch Sen X,” or enter something more


 Alarm On, select the alarm state (
Open
or
Closed

Features & Specications

 Alarm Prole, which controls light towers and relays on your Room Alert, you may
leave the default,
Prole 1

 Select
Save Settings



www.serverroomenvironments.co.uk
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Avtech RMA-FS2-SEN User manual

Type
User manual

Avtech RMA-FS2-SEN is a flood sensor that can be used to detect the presence of liquid on a flat surface. It has two adjustable-height contacts that can be set to trip the sensor when liquid collects underneath the housing. The sensor comes with a 25' low-voltage 2-wire cable that can be used to connect it to a Room Alert or Wireless Sensor Hub. The sensor is powered by a 9V alkaline battery and has a maximum extendable length of 900'.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI