Hadco Direct Burial Posts (350, 360, 370) Install Instructions

Hadco
Brand
Hadco
Model
Direct Burial Posts (350, 360, 370)
Category
Motorcycle Accessories
Type
Install Instructions

This manual is also suitable for

Hadco Direct Burial Posts (350, 360, 370)

Hadco Direct Burial Posts are designed for use with underground electrical wiring. The posts have a 7/8" diameter wireway hole for easy installation of cables. The posts are made of aluminum and have a black powder-coated finish for durability. They come in three sizes: 350mm, 360mm, and 370mm.

Features:

  • Made of aluminum for durability
  • Black powder-coated finish
  • 7/8" diameter wireway hole
  • Three sizes available: 350mm, 360mm, and 370mm

Use Cases:

  • Installing underground electrical wiring
  • Lighting pathways, driveways, and other outdoor areas

Hadco Direct Burial Posts (350, 360, 370)

Hadco Direct Burial Posts are designed for use with underground electrical wiring. The posts have a 7/8" diameter wireway hole for easy installation of cables. The posts are made of aluminum and have a black powder-coated finish for durability. They come in three sizes: 350mm, 360mm, and 370mm.

Features:

  • Made of aluminum for durability
  • Black powder-coated finish
  • 7/8" diameter wireway hole
  • Three sizes available: 350mm, 360mm, and 370mm

Use Cases:

  • Installing underground electrical wiring
  • Lighting pathways, driveways, and other outdoor areas
Signify North America Corporation
200 Franklin Square Drive
Somerset, NJ 08873
Telephone 855-486-2216
Signify Canada Ltd.
281 Hillmount Road,
Markham, ON, Canada L6C 2S3
Telephone 800-668-9008
18
" OR DEEPER
10
"
AT LEAST
4
"
QUICK
DISCONNECT
TO
LAMP
GASKET
WASHER
STAMPED HOLE SUPPLIED IN POST
AS SHOWN. (HANOVER LANTERN
POST ONLY)
11/16" DIA.
HOLE
INSTALLATION INSTRUCTIONS FOR PHOTO CONTROL
INSTALLATION INSTRUCTIONS FOR CONVENIENCE OUTLET
INSTALLATION INSTRUCTIONS FOR PHOTO CONTROL WITH DOOR
NOTE
: ALL WIRING SHOULD COMPLY WITH LOCAL CODES.
ALL WIRING SHOULD BE DONE BY A QUALIFIED ELECTRICIAN.
THIS END
DOWN
A
C
B
C
A
D
B
1. TURN OFF ALL POWER.
2. TO INSTALL PHOTOCELL ATTACH RED WIRE FROM PHOTOCELL
TO THE LEAD FROM THE LAMP. ATTACH THE WHITE WIRE FROM
THE PHOTOCELL TO THE COMMON WIRE. ATTACH THE BLACK WIRE
FROM THE PHOTOCELL TO THE INCOMING HOT LINE.
3. SLIDE NEOPRENE B WASHER OVER THREADED END OF PHOTO
CONTROL A
4. SLIDE PHOTO CONTROL A INTO 11/16" DIA. HOLE OF POST.
5. THREAD ROUND KNURLED NUT C ONTO THREADED ENDOF A .
(TIGHTEN) MAKE SURE PHOTO CONTROL'S A LONG LENGTH IS
VERTICAL INSIDE POST. (WIRES OF PHOTO CONTROL MUST BE
TURNED UP AS SHOWN IN ILLUSTRATION.) MAINTAIN DRIP LOOP
AS SHOWN IN ILLUSTRATION.
6. WHEN ALL FINAL CONNECTIONS ARE MADE, POWER MAY BE
TURNED ON.
7/8" DIA.
WIREWAY
HOLE.
GROUND
LINE
DIRECT BURIAL
POSTS.
1. TURN OFF ALL POWER.
2. PLACE GASKET B BETWEEN
POST & OUTLET A.
3. CONNECT BLACK OF OUTLET
TO BLACK OF POWER.
4. CONNECT WHITE OF OUTLET
TO WHITE OF NEUTRAL POWER.
5. CONNECT GREEN OF OUTLET
TO GREEN OF GROUND POWER.
6. USE WIRE NUTS D ON ALL
CONNECTIONS.
7. PUSH ALL WIRES BACK INTO
LARGE HOLE IN POST.
8. SECURE OUTLET TO POST WITH
2 EA. SCREWS C THRU 2 EA.
TAPPED HOLES IN POST.
9. TURN ON POWER.
COMM.
BLACK
WHITE
WHITE
COMM.
LOCKNUT
A
D
B
C
1. TURN OFF ALL POWER.
2. TO INSTALL PHOTOCELL ATTACH RED WIRE FROM PHOTOCELL
TO THE LEAD FROM THE LAMP. ATTACH THE WHITE WIRE FROM
THE PHOTOCELL TO THE COMMON WIRE. ATTATCH THE BLACK
WIRE FROM THE PHOTOCELL TO THE INCOMING HOT LINE.
3. USE WIRE NUTS A ON ALL CONNECTIONS.
4. PUSH ALL WIRES BACK INTO LARGE HOLE IN POST.
5. ATTACH DOOR ASSEMBLY B TO POST C W/ 2 EA.
SCREWS D THRU 2 EA. 8-32 TAP THRU HOLES OF POST.
6. TURN ON POWER.
2 EA. 8-32 TAP THRU HOLES.
BLACK
LINE
DRIP LOOP
BLACK
RED
WHITE
BLACK
WHITE
GREEN
INSTALLATION INSTRUCTIONS FOR DIRECT BURIAL POSTS
1. CONSULT WITH LOCAL AUTHORITIES AS TO SPECIFIC BUILDING & ELECTRICAL CODES. THE
FOLLOWING
STEPS SHOULD HELP YOU MEET THOSE CODES.
2. EXCAVATE A HOLE APPROXIMATELY 20" DEEP OR DEEPER DEPENDING ON FROSTLINE IN YOUR
AREA.
THEN ADD APPROXIMATELY 2" OF STONES IN BOTTOM FOR DRAINAGE.
3. INSTALL CABLE FROM HOUSE TO FIXTURE POST IN TRENCH. MAKE SURE CABLE IS SUITABLE FOR
UNDERGROUND BURIAL.
4. INSERT CABLE THRU WIREWAY HOLE 10" FROM BOTTOM OF POST, LEAVING MINIMUM OF 6"
EXTENDED BEYOND TOP OF POST.
5. NOTE: SOME CONCRETES HAVE HIGH ALKALI CONTENT THAT CAN DAMAGE ALUMINUM. TO
PREVENT DAMAGE
COAT INGROUND PORTION OF POST WITH AN ASPHALT BASE PAINT.
6. INSERT POST IN CENTER OF HOLE & BRACE ON 3 SIDES. POUR CONCRETE IN HOLE BEING CAREFUL
THAT CONCRETE DOES NOT ENTER BOTTOM OF POST OR WIREWAY HOLE.
7. ALLOW CONCRETE TO HARDEN BEFORE REMOVING BRACES.
WHEN INSTALLING POST, MAKE SURE THE END WITH THE YELLOW LABLE W/ BLACK
PRINT IS BURIED AS PER ARROWS ON LABEL.
CONCRETE FOOTER TO BELOW LOCAL FROST LEVEL OR LOCAL CODE
32H20-189-00, revision B
INSTALLATION INSTRUCTIONS:
DIRECT BURIAL
POSTS & ACCESSORIES
page 1 of 1
  • Page 1 1

Hadco Direct Burial Posts (350, 360, 370) Install Instructions

Hadco
Brand
Hadco
Model
Direct Burial Posts (350, 360, 370)
Category
Motorcycle Accessories
Type
Install Instructions
This manual is also suitable for

Hadco Direct Burial Posts (350, 360, 370)

Hadco Direct Burial Posts are designed for use with underground electrical wiring. The posts have a 7/8" diameter wireway hole for easy installation of cables. The posts are made of aluminum and have a black powder-coated finish for durability. They come in three sizes: 350mm, 360mm, and 370mm.

Features:

  • Made of aluminum for durability
  • Black powder-coated finish
  • 7/8" diameter wireway hole
  • Three sizes available: 350mm, 360mm, and 370mm

Use Cases:

  • Installing underground electrical wiring
  • Lighting pathways, driveways, and other outdoor areas
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents