Whirlpool AKR 667 IX Owner's manual

Brand: Whirlpool

Model: AKR 667 IX

Category: Cooker hoods

Type: Owner's manual

5019 318 33208

INSTALLATION UND GEBRAUCH

Installationsanweisungen: Bei der Installation der Abzugshaube sind folgende Mindestabstände einzuhalten:

50 cm bei Elektrokochplatten, 65 cm bei Gas-, Öl- oder Kohlekochplatten. Schreiben die

Installationsanweisungen des Gaskochfelds einen größeren Abstand vor, ist dieser natürlich zu beachten.

Achtung! Prüfen Sie, ob das Auslassrohr und die Befestigungsmanschetten im Lieferumfang inbegriffen sind.

Andernfalls müssen sie gesondert erworben werden.

Hinweis für Installation und Gebrauch: Lesen Sie vor dem Gebrauch der Abzugshaube aufmerksam die

vorliegende Gebrauchsanweisungen; die Abbildungen finden Sie auf den ersten Seiten. Der Hersteller lehnt jede

Haftung für Störungen, Schäden oder Feuer ab, die bei Missachtung der vorliegenden Gebrauchsanweisungen

durch das Gerät entstehen sollten.

Sie sollten einen qualifizierten Techniker mit der Installation beauftragen.

INSTALLATION AND USE

For installation: The hood must be installed at least 50 cm from electric cookers and 65 cm from combination

cookers. If the installation instructions for a gas cooker specify a greater distance, then this distance must be

observed.

Important! Check whether the exhaust pipe and clamps are provided. If not, they must be purchased

separately.

For installation and use: Before installing or using the hood, read this manual carefully. The drawings are at the

front of the manual. The Manufacturer declines all liability for any faults, damage or fires caused by the appliance

as a result of failure to observe the instructions and recommendations given in this manual.

Contact a qualified technician for installation.

MONTAGE ET UTILISATION

Remarque pour le montage : La hotte doit être installée à une distance minimum de 50 cm des cuisinières

électriques et de 65 cm des cuisinières à gaz ou mixtes. Si les instructions d'installation du dispositif de cuisson à

gaz indiquent une distance supérieure, il est nécessaire de la respecter.

Attention ! Vérifiez que le tuyau d'évacuation et les colliers de fixation sont fournis avec l'appareil. Dans le cas

contraire, ils doivent être achetés à part.

Remarque pour le montage et l'utilisation : Avant de monter ou d'utiliser la hotte, lisez attentivement cette

notice et consultez les dessins qui se trouvent aux premières pages. Le fabricant décline toute responsabilité en

cas d'inconvénients, dommages ou incendies provoqués par l'appareil et dus à la non-observation des instructions

contenues dans cette notice.

Il est conseillé de consulter un technicien qualifié pour procéder au montage.

INSTALLATIE EN GEBRUIK

Opmerking bij de installatie: de wasemkap moet op een minimale afstand van 50 cm van elektrische kooktoestellen

en 65 cm van kooktoestellen op gas of gemengde kooktoestellen geïnstalleerd worden. Als de installatie-instructies van

het kooktoestel op gas een grotere afstand aangeven, moet hiermee rekening gehouden worden.

Let op! Controleer of de afvoerpijp en de klembanden bijgeleverd zijn. Zo niet, dan moeten ze apart worden

aangeschaft.

Opmerking bij de installatie en het gebruik: lees voordat u de wasemkap installeert of gebruikt deze

handleiding zorgvuldig door; de afbeeldingen vindt u op de eerste pagina's. De fabrikant aanvaardt geen enkele

verantwoordelijkheid voor problemen, schade of brand veroorzaakt door het niet naleven van de instructies in

deze handleiding.

U wordt geadviseerd een deskundig installateur te raadplegen.

31833208.fm Page 1 Tuesday, July 18, 2006 10:40 AM

5019 318 33208

INSTALACIÓN Y UTILIZACIÓN

Nota para la instalación: la campana debe instalarse a una distancia mínima de 50 cm en caso de cocinas

eléctricas y 65 cm en caso de cocinas de gas o mixtas. Si en las instrucciones de instalación de la placa de cocina

a gas se especifica una distancia mayor respecto a la indicada, es necesario tenerlo en cuenta.

¡Atención! Compruebe si el tubo de descarga y las abrazaderas de fijación están en dotación. De lo contrario,

hay que comprarlos por separado.

Nota para la instalación y la utilización:antes de instalar o utilizar la campana, lea atentamente este manual; los

dibujos en encuentran en las primeras páginas. El fabricante declina toda responsabilidad por posibles inconvenientes,

daños o incendio del aparato, derivados del incumplimiento de las instrucciones indicadas en este manual.

Para la instalación se recomienda dirigirse a un técnico cualificado.

INSTALAÇÃO E UTILIZAÇÃO

Nota de instalação: O exaustor deve ser instalado a uma distância mínima de 50 cm em caso de fogões

eléctricos e de 65 cm em caso de fogões a gás ou mistos. Respeite as instruções de instalação do dispositivo de

cozedura a gás se estas especificarem uma distância superior à indicada.

Atenção! Verifique se o tubo de descarga e as braçadeiras de fixação foram fornecidos. Caso contrário, deverá

adquiri-los à parte.

Nota de instalação e uso: Antes de instalar ou utilizar o exaustor, leia com atenção este manual e os desenhos

que se encontram nas primeiras páginas. Declina-se toda e qualquer responsabilidade por eventuais

inconvenientes, danos ou incêndios provocados pelo aparelho derivados do não seguimento das instruções que

se encontram neste manual.

É aconselhável consultar um técnico qualificado para a instalação.

INSTALLAZIONE E USO

Nota di installazione: La cappa deve essere installata ad una distanza minima di 50 cm in caso di cucine

elettriche e di 65 cm in caso di cucine a gas o miste. Se le istruzioni di installazione del dispositivo di cottura a gas

specificano una distanza maggiore a quella specificata, bisogna tenerne conto.

Attenzione! Verificare se il tubo di scarico e le fascette di fissaggio sono forniti a corredo. In caso contrario,

vanno acquistati a parte.

Nota di installazione ed uso: Prima di installare o utilizzare la cappa leggere attentamente questo manuale, i

disegni si trovano nelle prime pagine. Si declina ogni responsabilità per eventuali inconvenienti, danni o incendi

provocati all’apparecchio derivati dall’inosservanza delle istruzioni riportate in questo manuale.

Si consiglia di consultare un tecnico qualificato per l’installazione.

ΕΓΚΑΤΑΣΤΑΣΗ ΚΑΙ ΧΡΗΣΗ

Σηµείωση για την εγκατάσταση: Ο απορροφητήρας πρέπει να εγκατασταθεί σε ελάχιστη απόσταση 50 cm

από ηλεκτρικές και 65 cm από κουζίνες αερίου ή µικτού τύπου. Εάν οι οδηγίες εγκατάστασης της εστίας αερίου

συνιστούν µεγαλύτερη απόσταση, σε σχέση µε εκείνη που έχει οριστεί, εφαρµόστε τις σχετικές οδηγίες.

Προσοχή! Ελέγξτε εάν ο σωλήνας απαγωγής

και τα κολάρα στερέωσης παρέχονται µε τον εξοπλισµό.

Σε διαφορετική περίπτωση πρέπει να τα προµηθευτείτε χωριστά.

Σηµείωση για την εγκατάσταση και χρήση: Πριν εγκαταστήσετε ή χρησιµοποιήσετε τον απορροφητήρα

διαβάστε προσεκτικά το παρόν εγχειρίδιο τα σχέδια του οποίου βρίσκονται στις πρώτες σελίδες. Ο

κατασκευαστής δεν φέρει καµ

ία ευθύνη για ενδεχόµενες βλάβες, ατυχήµατα ή πυρκαγιές που προκαλούνται

από τη συσκευή και οφείλονται στη µη τήρηση των οδηγιών του παρόντος εγχειριδίου.

Για την εγκατάσταση συνιστάται να απευθυνθείτε σε εξειδικευµένο τεχνικό.

31833208.fm Page 2 Tuesday, July 18, 2006 10:40 AM

5019 318 33208

31833208.fm Page 3 Tuesday, July 18, 2006 10:40 AM

5019 318 33208

31833208.fm Page 4 Tuesday, July 18, 2006 10:40 AM

5019 318 33208

31833208.fm Page 5 Tuesday, July 18, 2006 10:40 AM

5019 318 33208

EXTRACTOR OR FILTERING HOOD INSTALLATION

Important: the figures are on the first pages of this booklet

• Fix the bracket on the rear of the hood near the coupling ring (Fig. 1.1a).

Note: the bracket can be adjusted horizontally, which enables the position of the hood to be adjusted (Fig. 1.1b).

• Mark a centre-line on the wall from the cooktop to the ceiling (Fig 2.2).

Taking into account the distances from the cooktop, mark the distance from the cooktop with a pencil and place the

template against the wall on the mark (Fig 2.3).

Then mark and drill the hole, insert the wall plug and partially tighten 1 screw (Fig. 2.4).

• Fix the flue support to the wall as close as possible to the ceiling (Fig 3.1). For filter hoods, also secure the deflector at this

stage (Fig 3.2).

Hang the hood on the partially tightened screw (Fig. 3.3a - if necessary, adjust the hood horizontally by means of the

bracket - Fig- 3.3b)

Mark the hood fixing points:

2 at the bottom: remove the grease filters (Fig. 3.4), 2 at the top on the sides of the bracket.

Remove the hood, drill, insert the wall plugs (Fig 3.5), refit the hood and firmly tighten all the screws (Fig.3.6 - Fig. 3.7).

Extractor Version: fumes are extracted and expelled to the outside through a fumes exhaust hose fixed to the collar at the top

of the hood and secured with the special clamp.

Important! If the hood is equipped with a carbon filter, this must be removed.

The discharge air must not be ducted to a flue used for removing fumes produced by appliances using gas or other fuels, but

must have a separate outlet. All national regulations on air discharge must be observed.

Filter Hood: Air is filtered through a carbon filter and recycled into the surrounding environment.

In this case, fit a fume hose between the collar on the hood and the deflector collar, using clamps.

Important! If the hood does not have a carbon filter, order one and fit it before use.

Telescopic flue installation

• Connect the hood to the mains supply and fix the telescopic flue to the flue bracket with two screws. Slide the bottom

section down into its seat on the top of the hood (Fig. 4).

D F NL E

PIGR

31833208.fm Page 9 Tuesday, July 18, 2006 10:40 AM

5019 318 33208

1. Control panel.

Light :

move the switch to the right or press the button to switch

on.

Extraction speed :

Move the switch to the right or press the next button to

increase extraction speed (or open the electric shutter) .

2. Grease filters

3. Lamp covers (or halogen lamps, depending on the

model).

4. Telescopic flue.

Grease filters:

Metal grease filters have an unlimited

life and should be washed once a

month either by hand or in a

dishwasher at a low temperature and

with a short cycle. Washing in a

dishwasher can cause grease filters to

turn white, but this in no way affects

efficiency.

Press the handle to release the filter

Wash the filter and leave it to dry, proceeding in reverse

order to refit it.

Bulb/s:

Detach the lighting unit and remove

the burnt-out bulb.

Refit the filters.

Halogen lamps.

Use a small screwdriver or other

suitable tool to prise off the cover.

Snap-fit the cover back on.

Use only max 40W

E14 bulbs or max 20 W halogen

bulbs (depending on the model),

taking care not to touch them with

your hands.

Fitting or replacing the carbon filter

(filter hoods only).

Change the carbon filter every six months.

1. Remove the grease filters.

2. Fit the filters as shown in the figures below.

3. Reverse the above procedure to remove the carbon

filter.

4. Refit the grease filters.

CLACK!

D F NL E

PIGR

31833208.fm Page 10 Tuesday, July 18, 2006 10:40 AM

5019 318 33208

SAFEGUARDING THE ENVIRONMENT

1. Packaging

Packaging materials are 100% recyclable and are marked with

the recycling symbol . Dispose of the appliance in conformity

with local environmental regulations. Packaging materials (plastic

bags, polystyrene, etc.) can be dangerous for children and should

be kept well out of their reach.

2. Product

This appliance is marked in compliance with European Directive

2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).

By ensuring that this appliance is scrapped suitably, you can help

prevent potentially damaging consequences for the environment

and health.

The symbol on the appliance or accompanying

documentation indicates that this product should not be

disposed of as unsorted municipal waste but must be taken to a

collection point for the treatment of WEEE.

Disposal must be carried out in accordance with local

environmental regulations for waste disposal.

For further information on the treatment, recovery and recycling

of this appliance, contact your competent local authority, the

collection service for household waste or the shop where you

purchased the appliance.

PRECAUTIONS AND GENERAL

RECOMMENDATIONS

IMPORTANT!

• The appliance is not intended for use by young

children or infirm persons without supervision.

• Young children should be supervised to ensure that

they do not play with the appliance.

1. Do not connect the appliance to the mains electricity supply

until installation is completed. Always disconnect the hood from

the mains before performing any cleaning or maintenance.

2. Do not “flambé” food under the hood. Naked flames could

cause a fire.

3. Do not leave pans unattended when frying. Cooking oil can

catch fire.

4. Regular cleaning and maintenance is essential to correct

functioning and good performance. Regularly remove dirt

deposits. Regularly clean or replace filters. Never use

flammable materials as hoses for extracted air.

5. If the hood is used together with non-electrically powered

appliances, ambient negative pressure must not exceed 4Pa

(4 x 10

-5

bars). Make sure the room is adequately ventilated.

6. If the hood is used in extractor mode together with cookers,

ambient negative pressure must not exceed 4 Pa (4 x 10

-5

bars).

7. Exhaust air must not be conveyed through the same flue used

by the heating system or other non-electrical appliances.

8. The room must be adequately ventilated when the hood is

used together with appliances powered by gas or other

fuels.

9. When replacing the bulbs, first ensure that they are cold.

Note: always wear work gloves for all installation and

maintenance operations.

Electrical connections

Before connecting the hood to the power supply, make sure the

voltage specified on the dataplate matches that in your home.

The dataplate is located inside the hood behind the grease filter.

If the appliance is fitted with a power cable and plug, the plug

must be placed in an accessible position.

If the hood does not come pre-fitted with a mains plug, fit one

that conforms to applicable standards or use a double-pole

switch with a minimum breaking gap of 3 mm.

Replacement of the power supply cable with power plug or

flexible cable may only be carried out by an authorized Service

Centre or a qualified electrician.

Cleaning the hood

Important! Failure to remove oil and grease (at least once a

month) could lead to fire.

Use a soft cloth with a neutral detergent. Never use abrasive

substances or alcohol.

Before using the hood

Please read these instructions carefully and keep them for future

reference, in order to ensure best use of your hood.

Packaging materials (plastic bags, polystyrene, etc.) can be

dangerous for children and should be kept well out of their

reach.

Make sure the hood has not been damaged during transport.

Installation, electrical connections and replacement of the mains

lead with a plug or new flexible cable must be carried out by a

qualified technician in compliance with local safety regulations.

This appliance is designed to be used only by adults.

Declaration of conformity

This product has been designed, manufactured and sold in

conformity to the following standards:

- safety objectives of "Low Voltage" Directive 73/23/EEC

- protection requirements of “EMC” Directive 89/336/EEC

amended by Directive 93/68/EEC

Troubleshooting guide

The hood does not work

• Is the plug properly inserted in the power socket?

• Is there a power failure?

• Is the fuse blown?

The hood is not extracting efficiently:

• Is the right speed selected?

• Do the filters need cleaning or replacing?

• Are the air outlets blocked?

The light does not work:

• Does the bulb need replacing?

• Is the bulb correctly fitted?

• Is the fuse blown?

AFTER-SALES SERVICE

Before calling the After-sales Service

1. Check if you can fix the problem yourself (see

"Troubleshooting guide")

2. Switch the hood off and then on again to check if the

problem has gone.

3. If the problem persists, contact the After-sales Service.

Specify:

• the nature of the problem,

• the model of hood, stated on the data plate inside the hood,

accessible by removing the grease filters.

• your full address,

• your telephone number and area code,

• the service code (the number appearing below the word

SERVICE on the data plate inside the hood behind the grease

filter).

If any repairs are needed, contact an authorized Service Centre

(to ensure that only original spare parts are used and that repairs

are made correctly).

Failure to comply with these instructions may compromise the

safety and quality of the product.

D F NL E

PIGR

31833208.fm Page 11 Tuesday, July 18, 2006 10:40 AM

Whirlpool AKR 667 IX Owner's manual

Brand: Whirlpool

Model: AKR 667 IX

Category: Cooker hoods

Type: Owner's manual

Download PDF

report

Whirlpool AKR 667 IX Owner's manual

Whirlpool AKR 667 IX Owner's manual

Related papers

Other documents