Banner MSDINT-1L2 User manual

Brand: Banner

Model: MSDINT-1L2

Type: User manual

MINI-SCREEN Controller Models

MSDINT-1 and MSDINT-1L2

Supplement to MINI-SCREEN Instruction Manual 44895

Printed in USA 04/00 P/N 62875

Figure 20. MINI-SCREEN System electrical connections.

MODEL NO.

MSDINT-1 or 1L2

123OK

STEADY FLASHING

Blocked or Latched

Clear

Reset

Lockout

Blanking

Alignment

BANNER ENGINEERING CORP., USA

(612) 544-3164

For control reliable

operation always follow the

instructions in the manual.

Shock hazard may exist.

Diagnostic

Chart on

Reverse Side

CAUTION

MINI-SCREEN

LISTED

Presence

Sensing

Device

10Y8

0466

WARNING

SSD

AUX

ALARM



FSD2



Key 1 Key 2



FSD1

+24

V dc

Com

32 33 34

Test 1

LATCH

RESET 1

Test 2

LATCH

RESET 2

+12V

COM T/R T/R DRAIN

13 14

15 16 17



Figure 17. Control Module Dimensions and Mounting Hole Locations.

83.8 mm

(3.30")

110.0 mm

(4.33")

100.0 mm

(3.94 ")

Combo Head (Phillips/Slotted) Screws

M3.5 x 0.6 mm x 14 mm (2) (#6 x 0.5" equivalent) (Supplied)

M3.5 mm Washers (2) (#6 equivalent) (Supplied)

M3.5 mm x 0.6 mm Nuts (2) (36 equivalent) (Supplied)

Recommended torque is 16 in-lbs on mounting screws

Slot for Screws (2)

M3.5 x 0.6 mm (2)

35.0 mm

(1.38")

DIN Mounting Slot

DIN Mounting Tab

(Supplied)

60.8 mm

(2.40")

85.3mm

(3.36")

7.4 mm

(0.29")

7.1 mm

(0.28")

The enclosed MINI-SCREEN controller

MSDINT-1, MSDINT-1L2, or replacement

board reflect the new MINI-SCREEN DIN

controller design. These controllers are

identical to the old MINI-SCREEN DIN

controller, except that they have

removeable wiring blocks. With the

removeable wiring blocks, wiring terminal

numbers change and one overall

controller dimension increases. This

supplement modifies the information for

figures 17, 20, and 23, which appear in

MINI-SCREEN manual 44895.

Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN 55441 • Phone: (763) 544-3164 • Fax: (763) 544-3573 • E-mail: sens[email protected]

MSDINT-1 or MSDINT-1L2

WARNING. . .

Use of MINI-SCREEN

Systems for Perimeter

Guarding

If control module model MSDINT-1T2 is

used for perimeter guarding, the Machine

Primary Control Elements (MPCEs) of the

guarded machine must be wired so that

the trip output of the control module

causes a latched response of the MPCEs.

The MPCEs must be reset only by

actuation of a reset switch.

The reset switch must be located outside

of the area of dangerous motion, and

must be positioned so that the area of the

dangerous motion may be observed by

the switch operator during the reset

operation. Supplemental presence

sensing devices, such as safety mats,

must be used if any space between the

defined area and any danger point is

large enough to allow a person to stand

undetected by the MINI-SCREEN System.

Failure to observe this warning could

result in serious bodily injury or death.

Secondary Switching

Device

SSD

MSCE

Machine Secondary

Control Element

Arc Suppression

(see warning)

Final Switching

Device #2

FSD 2

MPCE

Machine Primary

Control Element #2

Arc Suppression

(see warning)

Final Switching

Device #1

FSD 1

MPCE 1 MPCE 2

+ (V dc)

MINI-SCREEN

Control Module

– (V dc)

Machine Primary

Control Element #1

Arc Suppression

(see warning)

MPCE

Monitor

Contacts

+24V dc

Earth

Ground

common

L (V ac)

+ (V dc)

N (V ac)

common (V dc)

Model MSDINT-1: Trip Output

Model MSDINT-1L2: Latch Output

MPCE

Machine

Control

Circuit

Figure 23. Generic machine interface, MINI-SCREEN System

WARNING. . .

All MINI-SCREEN System output contacts (FSD1, FSD2, and SSD)

must be used. The generalized wiring configuration, shown here, is

provided only to illustrate the importance of proper installation. The

actual details of wiring of the MINI-SCREEN system to any particular machine is

solely the responsibility of the installer and end user.

WARNING. . .

If arc suppressors are used, they MUST BE INSTALLED AS SHOWN

ACROSS THE COILS OF THE MACHINE CONTROL ELEMENTS.

NEVER INSTALL SUPPRESSORS DIRECTLY ACROSS THE

CONTACTS OF THE MINI-SCREEN SWITCHING DEVICES! It is possible for

suppressors to fail as a short circuit. If installed directly across the contacts of a

MINI-SCREEN switching device, a short-circuited suppressor will create an

unsafe condition.

Figure 23 (below) shows output relay connections in a generic interfacing situation.

The connections between the MINI-SCREEN System outputs and the machine primary

and secondary control elements must be direct, and arranged so that any single line

fault or earth fault will not result in a circuit failure to a potentially dangerous state.

Banner MSDINT-1L2 User manual

Banner MSDINT-1L2 User manual

Banner MSDINT-1L2 User manual

Related papers

Other documents