Kenwood KVT-617DVD Installation guide

Type
Installation guide

This manual is also suitable for

© B54-4502-00/00 (KV/RV)
KVT-617DVD
KVT-647DVD
MONITOR WITH DVD RECEIVER
INSTALLATION MANUAL
MONITEUR AVEC REPTEUR DVD
MANUEL D'INSTALLATION
MONITOR CON RECEPTOR DVD
MANUAL DE INSTALACION
MONITOR COM RECEPTOR DVD
MANUAL DE INSTALAÇAO
2
|
English
Accessories
1
..........1
2
..........1
3
..........1
4
..........1
5
..........1
6
..........2
7
..........4
8
..........4
9
..........2
0
..........2
!
..........4
@
..........4
English
|
3
Installation Procedure
1. To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2. Make the proper input and output wire connections
for each unit.
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the following
order: ground, battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
8. Press the reset button.
2WARNING
• If you connect the ignition wire (red) and the
battery wire (yellow) to the car chassis (ground),
you may cause a short circuit, that in turn may start
a fire. Always connect those wires to the power
source running through the fuse box.
• Do not cut out the fuse from the ignition wire (red)
and the battery wire (yellow). The power supply
must be connected to the wires via the fuse.
2CAUTION
• If the power is not turned ON (or it is ON, but
will be OFF immediately), the speaker wire may
have a short-circuit or touched the chasis of the
vehicle and the protection function may have been
activated. Therefore, the speaker wire should be
checked.
• If your cars ignition does not have an ACC position,
connect the ignition wires to a power source that
can be turned on and off with the ignition key. If
you connect the ignition wire to a power source
with a constant voltage supply, as with battery
wires, the battery may die.
• If the console has a lid, make sure to install the
unit so that the faceplate will not hit the lid when
closing and opening.
• If the fuse blows, first make sure the wires aren’t
touching to cause a short circuit, then replace the
old fuse with one with the same rating.
• Insulate unconnected wires with vinyl tape or other
similar material. To prevent a short circuit, do not
remove the caps on the ends of the unconnected
wires or the terminals.
• Connect the speaker wires correctly to the terminals
to which they correspond. The unit may be
damaged or fail to work if you share the - wires or
ground them to any metal part in the car.
• When only two speakers are being connected to the
system, connect the connectors either to both the
front output terminals or to both the rear output
terminals (do not mix front and rear). For example,
if you connect the + connector of the left speaker
to a front output terminal, do not connect the -
connector to a rear output terminal.
• After the unit is installed, check whether the brake
lamps, blinkers, wipers, etc. on the car are working
properly.
• Mount the unit so that the mounting angle is 30° or
less.
4
|
English
Connection
FM /AM ANTENNA
AV IN PUT 1
AV IN PUT 2
LR
R
R
VIDEO
VIDEO
FRONT
REAR
PRE OUTPUT
AV OUTPUT
POWER
R-CAM V-IN
L
L
R
L
R
L
R
L
VIDEO
+
A
B
C
SUB
B
C
ANT CONT
P. CONT
EXT.CONT
(10A)
MUTE
PRK SW
REVERSE
(5A)
ACC
BATT
ILLUMI
REMO.CONT
A
B
C
Accessory 3
Do not connect.
Ground wire (Black) - (To car chassis)
Battery wire (Yellow)
Mute wire (Brown)
Motor antenna control wire (Blue)
Power control wire (Blue/White)
External amplifier control wire (Pink/Black)
Connect to the terminal that is grounded when either the
telephone rings or during conversation.
To connect the kenwood navigation system,
consult your navigation manual.
Depending on what antenna you are using, connect either to the
control terminal of the motor antenna, or to the power terminal for
the booster amplifier of the film-type antenna.
When using the optional power amplifier, connect to its power
control terminal.
To "EXT.AMP.CONT." terminal of the amplifier having the external
amp control function.
FM/AM antenna input
Antenna cord
Ignition key switch
Car fuse box
(Main fuse)
ACC
Car fuse box
Connect to the vehicle's parking brake detection
switch harness using the supplied relay connector.
Ground wire (Black) - (To car chassis)
Steering remote control input
(Light Blue/Yellow)
Dimmer control wire (Orange/White)
Reverse sensor wire (Pink)
For the sake of safety, be sure to
connect the parking sensor.
Parking sensor wire (Green)
To car light control switch
To vehicle's reverse lamp harness
To Steering remote
Battery wire (Yellow)
Ignition wire (Red)
Receiver unit (front side)
Monitor unit
Accessory 4
Accessory 1
Battery
English
|
5
TO NAVIGATION I/F TO 5L I/FTO TV TUNER I/F TO MONITOR I/F
TV ANTENNA INPUT
TO M ONITOR UNIT
+
+
+
+
FRONT LFRONT RREAR LREAR R
Accessory 2
To front left speaker
To front right speaker
To rear left speaker
To rear right speaker
White/Black
Gray
White
Gray/Black
Green/Black
Green
Purple
Purple/Black
Connection cable
(Included in the TV tuner)
Connection cable
(Included in the
Navigation system)
Connection cable
(Included in the disc changer)
Disc Changer etc. (Optional)
Receiver unit (rear side)
TV tuner (Optional)
Navigation System
(Optional)
If you connect the ignition wire (red) and the battery
wire (yellow) to the car chassis (ground), you may
cause a short circuit, that in turn may start a fire.
Always connect those wires to the power source
running through the fuse box.
6
|
English
FM /AM ANTENNA
R
FRONT
REAR
PRE OUTPUT
AV OUTPUT
POWER
R-CAM V-IN
L
R
L
R
L
VIDEO
SUB
R
L
AV INPUT 1
AV INPUT 2
LR
R
VIDEO
VIDEO
L
Front Preout
• Audio left output (White)
• Audio right output (Red)
Rear Preout
• Audio left output (White)
• Audio right output (Red)
Subwoofer Preout
• Audio left output (White)
• Audio right output (Red)
Rear View Camera Input
Visual input (Yellow)
Audio/Visual Output
Visual output (Yellow)
• Audio left output (White)
• Audio right output (Red)
Audio/Visual input 1 (KVT-617DVD)
Audio/Visual input (KVT-647DVD)
Visual input (Yellow)
• Audio left input (White)
• Audio right input (Red)
Connection for AV Equipments
Audio/Visual input 2 (KVT-617DVD only)
Visual input (Yellow)
• Audio left input (White)
• Audio right input (Red)
English
|
7
Installation for Monitor Unit
Installation for Receiver unit
Accessory 5
Bend the tabs of the mounting
sleeve with a screwdriver or similar
utensil and attach it in place.
Metal mounting strap
(commercially available)
Self-tapping screw
(commercially available)
Screw (M4X8)
(commercially available)
Firewall or metal support
Make sure that the unit is installed securely in place. If the unit is unstable,
it may malfunction (eg, the sound may skip).
1. Attach the installation brackets 9 to the sides of
the hideaway unit using the sems bolts 7.
2. Use the tapping screw 8 to secure the hideaway
unit to the audio board.
Installation brackets
(Accessory 9)
Sems bolts (M4 × 8 mm)
(Accessory 7)
Tapping screw (ø4 × 16 mm)
(Accessory 8)
8
|
English
Removing Monitor Unit
Removing the Hard Rubber Frame (escutcheon)
1. Engage the catch pins on the removal tool 6
and remove the two locks on the lower level.
Lower the frame and pull it forward as shown
in the figure.
2. When the lower level is removed, remove the
upper two locations.
Removing the Unit
1. Remove the hard rubber frame by referring
to the removal procedure in the section
<Removing the Hard Rubber Frame>.
2. Remove the Hex-head screw with integral
washer (M4 × 8) on the back panel.
3. Insert the two removal tools 6 deeply into
the slots on each side, as shown.
4. Lower the removal tool toward the bottom,
and pull out the unit halfway while pressing
towards the inside.
5. Pull the unit all the way out with your hands,
being careful not to drop it.
Be careful to avoid injury from the catch pins on
the removal tool.
Removal Tool (Accessory 6 )
Lock
Catch
Removal Tool (Accessory 6 )
English
|
9
Installation on Toyota, Nissan or Mitsubishi Car using Brackets at Holes shown by ""
or
Car Bracket
Accessory ! (M5x6mm)
or Accessory @ (M5x7mm)
Screws (included in
audio unit package)
Screws (included in
audio unit package)
Accessory ! (M5x6mm)
or Accessory @ (M5x7mm)
Audio unit or others
Installing in Japanese-Made Cars
10
|
English
Installation on Toyota Car using Brackets at Holes shown by ""
or
When using the bracket shown above, you cannot use screws at two holes of
the right and left unit sides. If so, tighten the bracket using accessories 0 as
shown below.
1. Use accessories 0 at both sides as shown.
Accessory 0
Audio unit or others
2. Mount the bracket at each side.
Accessory ! (M5x6mm)
Accessory ! (M5x6mm)
Screws (included in
audio unit package)
Screws (included in
audio unit package)
Car Bracket
English
|
11
3. Bend each end of accessory 0 to fix the bracket.
Use a flat-blade screwdriver or pliers, and bend
each accessory tab into the hole of installation
bracket to fix the bracket.
Installing in Japanese-Made Cars
12
|
Français
Accessoires
1
..........1
2
..........1
3
..........1
4
..........1
5
..........1
6
..........2
7
..........4
8
..........4
9
..........2
0
..........2
!
..........4
@
..........4
22
|
Español
Accesorios
1
..........1
2
..........1
3
..........1
4
..........1
5
..........1
6
..........2
7
..........4
8
..........4
9
..........2
0
..........2
!
..........4
@
..........4
32
|
Português
Acessórios
1
..........1
2
..........1
3
..........1
4
..........1
5
..........1
6
..........2
7
..........4
8
..........4
9
..........2
0
..........2
!
..........4
@
..........4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Kenwood KVT-617DVD Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI