SMC Networks SMC6724L3 INT User manual

TigerSwitch 10/100

24-Port 10/100 Managed Layer 3 Switch

◆ 24 10BASE-T/100BASE-TX auto MDI/MDI-X ports

◆ Optional 1000BASE-X or 100BASE-FX modules

◆ IP routing with RIP and OSPF

◆ 8.8 Gbps of aggregate bandwidth

◆ Non-blocking switching architecture

◆ Spanning Tree Protocol

◆ Up to six LACP or static 4-port trunks

◆ Port mirroring for non-intrusive analysis

◆ Layer 2/3/4 CoS support through four priority queues

◆ Full support for VLANs with GVRP

◆ IGMP and DVMRP multicast support

◆ Manageable via console, Web, SNMP/RMON

Installation Guide

SMC6724L3

38 Tesla

Irvine, CA 92618

Phone: (949) 679-8000

TigerSwitch 10/100

Installation Guide

From SMC’s Tiger line of feature-rich workgroup LAN solutions

November 2003

Pub. # 150200033800A

Information furnished by SMC Networks, Inc. (SMC) is believed to be

accurate and reliable. However, no responsibility is assumed by SMC for its

use, nor for any infringements of patents or other rights of third parties

which may result from its use. No license is granted by implication or

otherwise under any patent or patent rights of SMC. SMC reserves the

right to change specifications at any time without notice.

SMC Networks, Inc.

38 Tesla

Irvine, CA 92618

Trademarks:

SMC is a registered trademark; TigerSwitch isa a trademarks of SMC Networks, Inc. Other product and

company names are trademarks or registered trademarks of their respective holders.

i

L

IMITED

W

ARRANTY

Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be

free from defects in workmanship and materials, under normal use and service, for the

applicable warranty term. All SMC products carry a standard 90-day limited warranty from

the date of purchase from SMC or its Authorized Reseller. SMC may, at its own discretion,

repair or replace any product not operating as warranted with a similar or functionally

equivalent product, during the applicable warranty term. SMC will endeavor to repair or

replace any product returned under warranty within 30 days of receipt of the product.

The standard limited warranty can be upgraded to a Limited Lifetime* warranty by registering

new products within 30 days of purchase from SMC or its Authorized Reseller. Registration

can be accomplished via the enclosed product registration card or online via the SMC Web

site. Failure to register will not affect the standard limited warranty. The Limited Lifetime

warranty covers a product during the Life of that Product, which is defined as the period of

time during which the product is an “Active” SMC product. A product is considered to be

“Active” while it is listed on the current SMC price list. As new technologies emerge, older

technologies become obsolete and SMC will, at its discretion, replace an older product in its

product line with one that incorporates these newer technologies. At that point, the obsolete

product is discontinued and is no longer an “Active” SMC product. A list of discontinued

products with their respective dates of discontinuance can be found at:

http://www.smc.com/index.cfm?action=customer_service_warranty.

All products that are replaced become the property of SMC. Replacement products may be

either new or reconditioned. Any replaced or repaired product carries either a 30-day limited

warranty or the remainder of the initial warranty, whichever is longer. SMC is not responsible

for any custom software or firmware, configuration information, or memory data of

Customer contained in, stored on, or integrated with any products returned to SMC pursuant

to any warranty. Products returned to SMC should have any customer-installed accessory or

add-on components, such as expansion modules, removed prior to returning the product for

replacement. SMC is not responsible for these items if they are returned with the product.

Customers must contact SMC for a Return Material Authorization number prior to returning

any product to SMC. Proof of purchase may be required. Any product returned to SMC

without a valid Return Material Authorization (RMA) number clearly marked on the outside

of the package will be returned to customer at customer’s expense. For warranty claims within

North America, please call our toll-free customer support number at (800) 762-4968.

Customers are responsible for all shipping charges from their facility to SMC. SMC is

responsible for return shipping charges from SMC to customer.

ii

WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS

WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR

REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S OPTION. THE

FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN

LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED,

EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE,

INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. SMC NEITHER ASSUMES NOR

AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER

LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION,

MAINTENANCE OR USE OF ITS PRODUCTS. SMC SHALL NOT BE LIABLE

UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THE

ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY

CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT, IMPROPER

INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR

ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY

ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.

LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED IN CONTRACT

OR TORT (INCLUDING NEGLIGENCE), SHALL SMC BE LIABLE FOR

INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE

DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE, LOSS OF BUSINESS, OR

OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE

SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR

INTERRUPTION OF ITS PRODUCTS, EVEN IF SMC OR ITS AUTHORIZED

RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES

OR THE LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR

CONSUMER PRODUCTS, SO THE ABOVE LIMITATIONS AND EXCLUSIONS

MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL

RIGHTS, WHICH MAY VARY FROM STATE TO STATE. NOTHING IN THIS

WARRANTY SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS.

* SMC will provide warranty service for one year following discontinuance from the active

SMC price list. Under the limited lifetime warranty, internal and external power supplies, fans,

and cables are covered by a standard one-year warranty from date of purchase.

SMC Networks, Inc.

38 Tesla

Irvine, CA 92618

iii

C

OMPLIANCES

FCC - Class A

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause interference to radio communications.

It has been tested and found to comply with the limits for a Class A computing device pursuant to

Subpart B of Part 15 of FCC Rules, which are designed to provide reasonable protection against

such interference when operated in a commercial environment. Operation of this equipment in a

residential area is likely to cause interference, in which case the user, at his own expense, will be

required to take whatever measures may be required to correct the interference. You are cautioned

that changes or modifications not expressly approved by the party responsible for compliance

could void your authority to operate the equipment.

You may use unshielded twisted-pair (UTP) cable for RJ-45 connections

—

Category 3 or greater

for 10 Mbps connections, Category 5 for 100 Mbps connections, and Category 5, 5e, or 6 for

1000 Mbps. Use 50/125 or 62.5/125 micron multimode fiber optic cable, or 9/125 micron

single-mode fiber optic cable, for SC or ST-type connections.

Wa r ni ng s :

1

. Wear an anti-static wrist strap or take other suitable measures to prevent electro-

static discharge when handling this equipment.

2.

When connecting this switch to a power outlet, connect the field ground lead on

the tri-pole power plug to a valid earth ground line to prevent electrical hazards.

Industry Canada - Class A

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital

apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,”

ICES-003 of the Department of Communications.

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils

numériques de Classe A prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques,”

NMB-003 édictée par le ministère des Communications.

C

OMPLIANCES

iv

EC Conformance Declaration - Class A

SMC contact for these products in Europe is:

SMC Networks Europe,

Edificio Conata II,

Calle Fructuós Gelabert 6-8,

2

o

, 4

a

,

08970 - Sant Joan Despí, Barcelona, Spain.

This information technology equipment complies with the requirements of the Council Directive

89/336/EEC on the Approximation of the laws of the Member States relating to Electromagnetic

Compatibility and 73/23/EEC for electrical equipment used within certain voltage limits and the

Amendment Directive 93/68/EEC. For the evaluation of the compliance with these Directives,

the following standards were applied:

Wa r ni ng :

Do not plug a phone jack connector in the RJ-45 port. This may damage this device.

Les raccordeurs ne sont pas utilisé pour le systéme téléphonique!

RFI Emission:

• Limit class A according to EN 55022:1998

• Limit class A for harmonic current emission according to

EN 61000-3-2/1995

• Limitation of voltage fluctuation and flicker in low-voltage supply

system according to EN 61000-3-3/1995

Immunity:

• Product family standard according to EN 55024:1998

• Electrostatic Discharge according to EN 61000-4-2:1995

(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)

• Radio-frequency electromagnetic field according to EN 61000-4-3:1996

(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)

• Electrical fast transient/burst according to EN 61000-4-4:1995 (AC/

DC power supply: ±1 kV, Data/Signal lines: ±0.5 kV)

• Surge immunity test according to EN 61000-4-5:1995

(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)

• Immunity to conducted disturbances, Induced by radio-frequency

fields: EN 61000-4-6:1996 (0.15 - 80 MHz with

1 kHz AM 80% Modulation: 3 V/m)

• Power frequency magnetic field immunity test according to

EN 61000-4-8:1993 (1 A/m at frequency 50 Hz)

• Voltage dips, short interruptions and voltage variations immunity test

according to EN 61000-4-11:1994 (>95% Reduction @10 ms, 30%

Reduction @500 ms, >95% Reduction @5000 ms)

LVD:

• EN 60950 (A1/1992; A2/1993; A3/1993; A4/1995; A11/1997)

C

OMPLIANCES

v

Japan VCCI Class A

Australia AS/NZS 3548 (1995) - Class A

SMC contact for products in Australia is:

SMC Communications Pty. Ltd.

Suite 18, 12 Tryon Road,

Lindfield NSW2070,

Phone: 61-2-94160437

Fax: 61-2-94160474

C

OMPLIANCES

vi

Safety Compliance

Warning: Fiber Optic Port Safety

Avertissment: Ports pour fibres optiques - sécurité sur le plan

optique

Warnhinweis: Faseroptikanschlüsse - Optische Sicherheit

Underwriters Laboratories Compliance Statement

Important!

Before making connections, make sure you have the correct cord set. Check it (read

the label on the cable) against the following:

The unit automatically matches the connected input voltage. Therefore, no additional adjustments

are necessary when connecting it to any input voltage within the range marked on the rear panel.

When using a fiber optic port, never look at the transmit laser while it is

powered on. Also, never look directly at the fiber TX port and fiber

cable ends when they are powered on.

Ne regardez jamais le laser tant qu’il est sous tension. Ne regardez

jamais directement le port TX (Transmission) à fibres optiques et les

embouts de câbles à fibres optiques tant qu’ils sont sous tension.

Niemals ein Übertragungslaser betrachten, während dieses eingeschaltet

ist. Niemals direkt auf den Faser-TX-Anschluß und auf die

Faserkabelenden schauen, während diese eingeschaltet sind.

Operating Voltage Cord Set Specifications

120 Volts UL Listed/CSA Certified Cord Set

Minimum 18 AWG

Type SVT or SJT three conductor cord

Maximum length of 15 feet

Parallel blade, grounding type attachment plug rated

15 A, 125 V

240 Volts (Europe only) Cord Set with H05VV-F cord having three

conductors with minimum diameter of 0.75 mm

2

IEC-320 receptacle

Male plug rated 10 A, 250 V

CLASS I

LASER DEVICE

DISPOSITIF LASER

DE CLASSE I

LASERGER

DER KLASSE I

ÄT

C

OMPLIANCES

vii

Wichtige Sicherheitshinweise (Germany)

1. Bitte lesen Sie diese Hinweise sorgfältig durch.

2. Heben Sie diese Anleitung für den späteren Gebrauch auf.

3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie keine Flüssigoder

Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung.

4. Die Netzanschlu ßsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein.

5. Das Gerät ist vor Feuchtigkeit zu schützen.

6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen

könnte Beschädigungen hervorrufen.

7. Die Belüftungsöffnungen dienen der Luftzirkulation, die das Gerät vor Überhitzung schützt.

Sorgen Sie dafür, daß diese Öffnungen nicht abgedeckt werden.

8. Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte.

9. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollte auch

nichts auf der Leitung abgestellt werden.

10. Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu beachten.

11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz

trennen. Somit wird im Falle einer Überspannung eine Beschädigung vermieden.

12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das Gerät

gelangen. Dies könnte einen Brand bzw. elektrischen Schlag auslösen.

13. Öffnen sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur von

authorisiertem Servicepersonal geöffnet werden.

14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer

qualifizierten Servicestelle zu überprüfen:

a. Netzkabel oder Netzstecker sind beschädigt.

b. Flüssigkeit ist in das Gerät eingedrungen.

c. Das Gerät war Feuchtigkeit ausgesetzt.

d. Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit

Hilfe dieser Anleitung keine Verbesserung erzielen.

e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.

f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.

15. Zum Netzanschluß dieses Gerätes ist eine geprüfte Leitung zu verwenden. Für einen

Nennstrom bis 6A und einem Gerätegewicht größer 3 kg ist eine Leitung nicht leichter als

H05VV-F, 3G, 0.75 mm

2

einzusetzen.

Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt 70dB(A) oder

weniger.

C

OMPLIANCES

viii

vii

T

ABLE

OF

C

ONTENTS

1 About the TigerSwitch 10/100 . . . . . . . . . . . . . . . . . . . . . . 1-1

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Switch Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Management Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Description of Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

RJ-45 Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Ports Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

System Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Optional Media Extender Modules . . . . . . . . . . . . . . . . . . . . . . . 1-7

Optional 10/100/1000BASE-T Module (SMC6824GT) . . 1-7

Optional 100BASE-FX Module (SMC6824FSSC) . . . . . . . 1-7

Optional 100BASE-FX Module (SMC6824FMSC) . . . . . . 1-8

Optional 1000BASE-X GBIC Module (SMC6824GB) . . . 1-8

Optional Redundant Power Unit . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

Power Supply Receptacle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

Expandability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

2 Network Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Introduction to Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Application Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Collapsed Backbone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Central Wiring Closet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Remote Connection with Fiber Cable . . . . . . . . . . . . . . . . . . . . . 2-4

Making VLAN Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Using Layer 3 Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Connectivity Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

1000 Mbps Gigabit Ethernet Collision Domain . . . . . .2-7

10/100 Mbps Ethernet Collision Domain . . . . . . . . . . . . . . . . . 2-8

Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

T

ABLE

OF

C

ONTENTS

viii

3 Installing the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

Selecting a Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Equipment Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Optional Rack-Mounting Equipment . . . . . . . . . . . . . . . . . . . . . 3-2

Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Desktop or Shelf Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Installing an Optional Module into the Switch . . . . . . . . . . . . . . 3-6

Installing a GBIC Transceiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Connecting to a Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

4 Making Network Connections . . . . . . . . . . . . . . . . . . . . . . .4-1

Connecting Network Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Twisted-Pair Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Cabling Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Connecting to PCs, Servers, Hubs and Switches . . . . . . . . . . . . 4-2

Wiring Closet Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

Fiber Optic Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

T

ABLE

OF

C

ONTENTS

ix

APPENDICES:

A Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Diagnosing Switch Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Power and Cooling Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

In-Band Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

B Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Twisted-Pair Cable and Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . B-2

10BASE-T/100BASE-TX Pin Assignments . . . . . . . . . . . . . . . . B-2

Straight-Through Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4

Crossover Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4

1000BASE-T Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . B-5

1000BASE-T Cable Requirements . . . . . . . . . . . . . . . . . . . . . . . B-6

Cable Testing for Existing Category 5 Cable . . . . . . . . . . . . . . . B-6

Adjusting Existing Category 5 Cabling . . . . . . . . . . . . . . . . . . . . B-6

Console Port Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7

Wiring Map for Serial Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7

C Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Physical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Base Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3

Slide-in Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3

100BASE-FX Extender Modules . . . . . . . . . . . . . . . . . . . . . . . . C-3

1000BASE-T Extender Module . . . . . . . . . . . . . . . . . . . . . . . . . . C-4

1000BASE-X GBIC Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5

D Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1

Glossary

Index

T

ABLE

OF

C

ONTENTS

x

1-1

C

HAPTER

1

A

BOUT

THE

T

IGER

S

WITCH

10/100

Overview

SMC’s TigerSwitch 10/100 (SMC6724L3) is an intelligent multilayer switch

with 24 10/100BASE-TX ports plus two slots on the front panel for

slide-in modules (100BASE-FX, 1000BASE-T, or GBIC transceivers).

There is also an SNMP-based management agent embedded on the main

board. This agent supports both in-band and out-of-band access for

managing the switch.

This switch can easily tame your network with full support for Spanning

Tree Protocol, Multicast Switching, Virtual LANs, and IP routing. It brings

order to poorly performing networks by segregating them into separate

broadcast domains with IEEE 802.3Q compliant VLANs, empowers

multimedia applications with multicast switching and CoS services, and

eliminates conventional router bottlenecks.

It can be used to augment or completely replace slow legacy routers,

off-loading local IP traffic to release valuable resources for non-IP routing

or WAN access. With wire-speed performance for Layer 2, Layer 3 and

Layer 4, this switch can significantly improve the throughput between IP

segments or VLANs.

A

BOUT

THE

T

IGER

S

WITCH

10/100

1-2

Figure 1-1. SMC6724L3 Front and Rear Panels

Switch Architecture

The switch employs a wire-speed, non-blocking switching fabric. This

permits simultaneous wire-speed transport of multiple packets at low

latency on all ports. This switch also features full-duplex capability on all

ports, which effectively doubles the bandwidth of each connection.

Auto-negotiation is used to select the optimal transmission speed and

communication mode for each connection. With store-and-forward

switching and flow control, maximum data integrity is always maintained,

even under heavy loading.

This switch includes two slots on the front panel for slide-in 1000BASE-T,

100BASE-FX, or 1000BASE-X (GBIC) modules. Cascade connections

between switches can be made using these modules.

System Indicators

Port Status Indicators

10/100 Mbps RJ-45 Ports

Media Slots

Console Port

Module Indicators

Power Socket Redundant Power Socket

O

VERVIEW

1-3

Management Options

This switch contains a comprehensive array of LEDs for “at-a-glance”

monitoring of network and port status. It also includes a management

agent that allows you to configure or monitor the switch using its

embedded management software, or via SNMP applications. To manage

the switch, you can make a direct connection to the RS-232 console port

(out-of-band), or you can manage the switch through a network

connection (in-band) using Telnet, the on-board Web agent, or

Windows-based network management software.

For a detailed description of the switch’s advanced features, refer to the

Management Guide.

A

BOUT

THE

T

IGER

S

WITCH

10/100

1-4

Description of Hardware

RJ-45 Ports

The switch base unit contains 24 10BASE-T/100BASE-TX RJ-45 ports.

All of these ports support automatic MDI/MDI-X operation, so you can

use straight-through cables for all network connections to PCs or servers,

or to other switches or hubs. (See “10BASE-T/100BASE-TX Pin

Assignments” on page B-2.)

Each of these ports support auto-negotiation, so the optimum

transmission mode (half or full duplex), and data rate (10 or 100 Mbps) can

be selected automatically. If a device connected to one of these ports does

not support auto-negotiation, the communication mode of that port can

be configured manually.

Each port also supports IEEE 802.3x auto-negotiation of flow control, so

the switch can automatically prevent port buffers from becoming

saturated.

Page is loading ...

SMC Networks SMC6724L3 INT User manual

This manual is also suitable for

SMC Networks SMC6724L3 INT User manual

Related papers

Other documents