CURT 11233 Installation guide

Type
Installation guide

CURT 11233 is a weight-carrying hitch specifically designed for 1992-2000 Lexus SC300 and SC400 coupes. It offers a gross load capacity of 2,000 lbs. for weight-carrying applications, such as hauling heavy cargo or equipment in a trailer. The hitch also features a 200 lbs. tongue weight capacity, which is the downward force exerted on the hitch by the trailer's tongue.

The CURT 11233 is engineered to be sturdy and durable, providing a secure connection between your vehicle and the trailer. It is designed for use with ballmounts #D-55001 / 45501, which are sold separately.

CURT 11233 is a weight-carrying hitch specifically designed for 1992-2000 Lexus SC300 and SC400 coupes. It offers a gross load capacity of 2,000 lbs. for weight-carrying applications, such as hauling heavy cargo or equipment in a trailer. The hitch also features a 200 lbs. tongue weight capacity, which is the downward force exerted on the hitch by the trailer's tongue.

The CURT 11233 is engineered to be sturdy and durable, providing a secure connection between your vehicle and the trailer. It is designed for use with ballmounts #D-55001 / 45501, which are sold separately.

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY AUXILIARY STABILIZING STRAPS.
** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY**
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
2,000 200
21
45
1992-2000 LEXUS COUPE SC300 & 400
11/13/2017
11233
90
257210
1. Locate the exhaust mufflers under the rear of the car at the left and right sides. The mufflers are supported
at the rear by a flexible support and bracket bolted into the chassis at the left and right sides of the car.
Large tie down plates are bolted under the exhaust support brackets using four 12mm bolts.
2. Remove the four 12mm bolts in each bracket and return the tie down brackets to the car's owner for
reinstallation should the hitch ever be removed.
3. This hitch will bolt in place where the tie down brackets were removed. Use the same 12 x 40mm fasteners
removed earlier to install the hitch. Refasten the exhaust support brackets at the two forward bolts at the
bottom of the hitch side plates.
4.Torque all 12mm fastners to 86 lb-ft.
DRIVER SIDE FRAME RAIL
PASSENGER SIDE FRAME RAIL
FLEXIBLE SUPPORT
AND BRACKET
(BOTH SIDES)
EXISTING 12mm BOLTS
-NO DRILLING REQUIRED
-USES ALL EXISTING FASTENERS
DESIGNED FOR USE WITH
BALLMOUNT #D-55001 / 45501
  • Page 1 1

CURT 11233 Installation guide

Type
Installation guide

CURT 11233 is a weight-carrying hitch specifically designed for 1992-2000 Lexus SC300 and SC400 coupes. It offers a gross load capacity of 2,000 lbs. for weight-carrying applications, such as hauling heavy cargo or equipment in a trailer. The hitch also features a 200 lbs. tongue weight capacity, which is the downward force exerted on the hitch by the trailer's tongue.

The CURT 11233 is engineered to be sturdy and durable, providing a secure connection between your vehicle and the trailer. It is designed for use with ballmounts #D-55001 / 45501, which are sold separately.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI