PAC BKHONK817 User manual

PAC
Brand
PAC
Model
BKHONK817
Type
User manual

This manual is also suitable for

PAC BKHONK817 is a vehicle-specific dash kit designed for installing a double DIN radio into a 2007-11 Honda CRV. It includes brackets, ISO spacers, and a pocket for single ISO mounting applications. Features ISO mountable radio brackets, provisions for single or double DIN radios, and a removable pocket for single DIN installations.

PAC BKHONK817 is a vehicle-specific dash kit designed for installing a double DIN radio into a 2007-11 Honda CRV. It includes brackets, ISO spacers, and a pocket for single ISO mounting applications. Features ISO mountable radio brackets, provisions for single or double DIN radios, and a removable pocket for single DIN installations.

©2016 AMERICAN INTERNATIONAL INDUSTRIES, INC.
TECH Ver. 10/16 PRINT Ver. 10/16
HONK817 Mounting Kit
VEHICLE APPLICATION
Honda
2007-11 CRV
iHONK817
www.aampglobal.com www.aius.net
2500 East Francis Street Ontario, CA 91761, U.S.A.
Sales: (800) 477-2267
Intl: (727) 572-9255
Support: 888-228-5560
Double DIN Applications
KIT ASSEMBLY INSTRUCTIONS
1. Remove the shaded tab from the bottom of each left and right mounting bracket
2. Attach the left and right side brackets to the main frame.
3. Cut and remove center rib from the main frame and le edges smooth.
4. Attach (1) ISO Spacer to the inside of upper section on both Left & Right
mounting brackets as shown in Fig. D.
5. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or hardware included with kit.
6. Slide radio component forward or backward for desired look and tighten screws
Fig. D
Cut
Cut
Attach (1) ISO Spacer to the inside of upper
section on both Left & Right mounting brackets
as shown in Fig. D.
Fig. E
Remove shaded tabs
on left and right sides
of the brackets
(Right side not shown)
Single DIN Mounting Applications
DASH DISASSEMBLY & RADIO REMOVAL INSTRUCTIONS
1. Carefully remove the climate controls with a plastic removal tool.
2. Disconnect harnesses from climate controls, set aside.
3. Carefully lift up and remove the cover panel from the top of the dash behind the vent
above the radio.
4. Carefully remove the vent assembly containing the hazard switch and passenger
airbag light.
5. Disconnect harness and set aside.
6. Remove the (4) Phillips screws securing the radio in the dash.
7. Gently remove radio and disconnect all harnesses attached.
KIT ASSEMBLY INSTRUCTIONS
1. Attach the left and right side brackets to the main bracket.
2. Insert pocket (part # POC817) into lower section of the main frame.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Insert DIN sleeve from your new radio into the upper section of the installation kit.
5. Depress the tabs from inside the sleeves opening upward, outward, and downward
to secure sleeve to the installation kit.
Note:
ISO trim ring (ITR817) may be used in place of after-market radio’s removable trim ring.
2
3
Single ISO Mounting Applications
KIT ASSEMBLY INSTRUCTIONS
1. Attach the left and right side brackets to the main bracket.
2. Insert pocket (part # POC-817) into lower section of the main frame.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Attach (1) ISO Spacer to the inside of upper section on both
Left & Right mounting brackets as shown in Fig. B.
5. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or hardware included with kit.
6.Slide radio component forward or backward for desired look and tighten screws.
Note:
#1 - ISO trim ring (ITR-817) may be used in place of after-market radio’s removable trim ring.
#2 - Spacers must read upright (This side up for single ISO install).
For ISO Mount Only: Attach (1) ISO Spacer
to the inside of upper section (See note #2)
on both Left & Right mounting brackets as
shown in Fig. B.
Fig. B
Fig. A
Fig. C
Main Frame
ITR817
(Optonal)
POC817
POC817
Main Frame
Metal Can
2007-11 HONDA CRV
Bracket
Bracket
Bracket
Bracket
ITR817
(Optonal)
  • Page 1 1
  • Page 2 2

PAC BKHONK817 User manual

PAC
Brand
PAC
Model
BKHONK817
Type
User manual
This manual is also suitable for

PAC BKHONK817 is a vehicle-specific dash kit designed for installing a double DIN radio into a 2007-11 Honda CRV. It includes brackets, ISO spacers, and a pocket for single ISO mounting applications. Features ISO mountable radio brackets, provisions for single or double DIN radios, and a removable pocket for single DIN installations.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents