Home Deconatons
-
Coflection
8F.22727
OXFORD COLLECTION 6 DOORS
CABINET
ASSEMBLY INSTRUCTIONS
Made In China
fhank
you
for
purchasing
this
quality product.Be.sure
to check all
packaging
mater
ial
careful ly for
sma11
parts,
which may have loose
inside
the carton
during
shipnent.0nce uppacked,
compare
all
parts
and
hardware
to the
provided
list to be
sure all
parts
are
present.
If
any
parts
or hardware
are missing
or damaged,
please
phone,e-mail
or fax
our
Custormer
service
Department.
For
speady
service,
please
provide
your
order
number, item
number and
part
number/letter
of the
part
needed
IMP0RTANT
NOTE:
Follow
instructions
listed below
in
proper
sequence as
numbered
to assure fast,
easy
and correct
assembly.
PARTS
LIST
A
S
TOP PANEL-1PC
B
BOTTOM
PANEL_1PC
C
LEFT
SIDE PANEL_1PC
D
RIGHT SIDE PANEL_1PC
E
SHELF_3PCS
T]
-r
ACROSS
PANEL_2PCS
G
RIGHT DOORS-3PCS
H
LEFT
DOORS_3PCS
BACK PANEL-2PCS
REAR PANEL
6UIDE_IPC
K
LOIV PANEL_1PC
DO\YELS_4PCS
LARCE MAGNETS_3PCS
N
\: i,
FEMALE
MAGNETS_6PCS
0
SCRE\Y_i
PC
P
w
SCRElVS-7 8PCS
a
H I NCES-12PCS
R
%
SCRE\vS-44PCS
S
w
SCRE\VS_4PCS
T
CAM-TOOL-1PC
U
fr
1,7\1..'
SHELF SUPPORTS-12PCS
\I
m
CAM-LOCKS-16PCS
W
CAM_BOLTS_16PCS
X
d
SCRE\VS-6PCS
r4
KNOB_6PCS
NOTE:
o
UPON 0PENING THOROUGHLY CLEAN ALL
W00DS SURFACES T0. REM0VE DUST
AND DIRT THAT IMAY HAVE SETTLED ONTO
FINISH DURING SHIPIV]ENT.IN ORDER
TO PREVENT DAMAGE DURING ASSEMBLY,PLEASE
ASSEfuIBLE
THIS
ITEM WITH
AT
LEAST TWO PEOPLE.
NOTE:
TURN THE
CAM-BOLT
SCREWS UNTIL THEY
ARE TIGHT,
THE
SHOULDER
SHOULD BE
AGAINST THE SURFACE OF THE PART.
HOW TO
USE
THE CAM-TOOL
NOTE:.THE
ARRows oN THE HIDDEN cAM-LocKS sHouLD
porNT
T0
THE
0AM-BoLTS
n
&
o
1
)
.ASSEMBLE THE D00RS(G/H)
ATTACH THE FEMALE
ATTACH THE KNOB(Y)
MAGNET( N)TO DOORS(G/H) USING
TO DOORS(G/H)USING SCREWS(X)
SCREWS
t
@
2).ASSEMBLE
THE SrpE PANEL(C/p).
r
ATTACH LOW PANEL(K)T0
B0TT0l!l PANEL(B)USING SCREW(0)
.
o
INSERT THE 4
D0WELS(L)INTO H0LES IN LOW
PANEL(K) .
o
ROTATE THE
CAM-B0LTS(W)INTO
HOLES lN SIDE
PANEL(C/D)
o
PLACE CAM-BOLTS(W)INTO HOLES
IN PANEL(B/F)AND ATTACH
'v
-@
@_,---*
3).ASSEMBLE
THE TCP PANEL(A).
o
ATTACH LARGE
IIIAGNETS(M)T0 ToP/ACRoSS
r
RoTATE
THE
CAM-BoLTS(W)INTo
HoLES
IN
'
PLACE CAM-BOLTS(W)INTo HOLES IN SIDE
o
INSERT 12 SHELF SUPPORTS(U)INTO
HOLES
PANEL(A/F)USTNG
6 SCREWS
(R
)
.
ToP PANEL(A).
PANEL(C/D)AND
ATTACH USrNG 4
CAM-LOCKS(V).
IN PANEL(Ci
D)AND PUT 3
SHELF(E) ONTO THEM.
NOTE:Attach the Ieft doon(H)by
the same
method as tne iignt doon(G)with
scnews
and hinges.
4) .ASSEMBLE THE D00RS(G/H) .
r
ATTACH 6 HINGES(0)To RIGHT D00RS(G)AND RIGHT SIDE
PANEL(D)USING
36 SCREWS(P).
Note:Befone
you
assemble
the back
panel,pl-ease
make
even
gap
anound them.If uneven,shift
the
unit
doonsane evenly spaced,then
attach back
panel
.
sune the doons have
an
LEFT
OR
RIGHT
UNTIL the
5).ASSEMBLE THE BACK PANEL(r).
o
INSERT THE,BACK
PANEL(I)INTO
SLOT
IN REAR PANEL GUIDE(J).
r
ATTACH
THE BACK PANEL(I)AND REAR PANEL
GUIDE(J)USING SCREWS(R/S)
/
