Juno JDK8460W User manual

Brand: Juno

Model: JDK8460W

Type: User manual

This manual is also suitable for

JDK8460S

Juno JDK8460W is a cooker hood that can be used in two modes: exhausting or recirculating. In the exhausting mode, the air is vented outdoors through a duct, while in the recirculating mode, the air is filtered through a carbon filter and recirculated into the room. The hood has three speeds, and it is equipped with a metal grease filter and a carbon filter (optional). The metal grease filter can be washed in the dishwasher, and the carbon filter should be replaced every 4 months.

Montage- und Gebrauchsanweisung

für den Dunstabzug

Instruction on mounting and use of the cooker hood

JDK 8460

Abb. 1

Fig. 1

Abb. 2

Fig. 2

Abb. 3

Fig. 3

Abb. 4

Fig. 4

Abb. 5

Fig. 5

OO123 I

Abb. 6

Fig. 6

K = nur Umluftbetrieb

K = only Recirculating version

Ø 150mm

Ø 120mm

12a

Hood Description - fig 1

1) Control panel

2) Grease filters

3) Work-lights

Use

The hood may be used as follows:

— Exhausting version

— Recycling version

Exhausting version

The air is vented outdoors by a duct which

must be connected to the connector ring

(See figure “Installation”).

Choosing the exhausting pipe

The connector ring has a diameter of 150mm.

We suggest to use Ø 150 mm exhausting

pipe.

Recycling version

The air is filtered through a carbon filter

(to install them see paragraph - Carbon

filter -) and recirculated into the room

through the grating on the upper chimney

part.

Attention!

If the hood is not supplied with carbon

filter, then it must be ordered and

mounted.

This version is used when there is no exhaust

duct for venting outdoors or when it is

impossible to install one.

Installation

When installed, the hood must be not less

than 65 cm. above electric burners or 75 cm.

above gas or mixed-fuel burners.

Warning!

— The hood cannot be connected to flues of

other appliances that run on energy

sources other than electricity.

— When the hood is used at the same time

of other appliances that run on energy

sources other than electricity, provision

must be made for an adequate supply of

air.

—No food must be cooked flambé

underneath the hood.

The use of an unprotected flame is

dangerous for the filters and could cause

fires.

Therefore, never use an open flame under

the hood. When frying foods, never leave

the pan alone because the cooking oil

could flare up.

— Please, keep to the provisions of official

directives regarding the question of fume

discharge.

— The manufacturers refuse to accept any

responsibility for damage to the hood or

its catching on fire because of failure to

observe the above instructions.

Suggestions for the installation and

use of the hood

— The horizontal sections of the pipe must

be slanted slightly upwards (about 10%)

to ensure an easy flow of the air outwards.

— The best performance of the unit is

obtained in the exhausting version,

therefore in the limits of the possibilities it

is advised to use the hood in this version.

— The best performances are obtained with

short pipes (max. 4 m) and with few

curves.

Electric connection

Before completing any connection, make

sure the house voltage corresponds with the

voltage indicated on the label affixed inside

the hood.

The hood is supplied with a standard plug;

connect it to a correspondingly standard

socket.

In the case is intended to connect the

appliance permanently to the mains after

having removed the plug supplied, must be

fitted a two-pole switch conforming to

regulations with an opening distance

between contacts of not less than 3mm.

The manufacturers are not liable for any

problems caused by the user’s failure to

observe the above instructions.

Mounting the hood - Fig. 6

a. Put the template onto the wall (1) and drill

two Ø12mm (2) and two Ø 8 mm (3)

holes.

b. Fit two hooks (4) on the drilled Ø 12mm

holes.

c. Fit two Ø 8mm wall dowels (5) on the

upper holes.

d. Remove the metal filters

e. Hang the hood on the hooks and adjust

the position of the hood using the two

screws on the bottom of the hooks (6).

f. Fix the hood definitively with two washers

(7) and two screws 5x45 mm (8).

Mounting the duct work

g. Mount the connector ring onto the hole in

the hood with two 3,5x9,5 screws (9a).

h. Fasten the support for the telescopic

chimney (11) with the three screw anchors

(10) and the three 5x45 screws (12).

i. Exhausting version: fasten a ventilation

duct, which is long enough to reach the

outside (13), to the connector ring (9a).

Recirculation version: mount the

deflector onto the telescopic chimney

support with two 2,9x9,5 screws.

Insert the adaptor (9b) into the connector

ring and then connect the hood to the

deflector with the ventilation duct (13).

j. Mount the telescopic chimney (14), fasten

it above with two screws (15), slide the

bottom part of the telescopic chimney

towards the bottom (16) and fasten the

hood in place definitively (17).

Operation

The hood has one variable speed motor. For

the best performance, we recommend using

the low speeds in normal conditions and the

high speeds in particular cases of strong

odour and vapour concentration.

We recommend starting up the hood a few

minutes before cooking and keeping it

running until all the odours have been

eliminated.

A- Motor OFF button

B - ON button and motor speed selection

button 1 - 2 - 3 - 1 - 2 - . . . .

E - Speed 1 LED

F - Speed 2 LED and grease filter

saturation LED (flashes)

C - Speed 3 LED and carbon filter

saturation LED (flashes)

D - Intensive speed indicator LED

G - Intensive speed ON switch

This speed should be used when the

concentration of cooking fumes or

odours is particularly strong (for

example when frying, cooking fish

etc.).

The fast speed will run for about 5

minutes and then return to the speed

previously set automatically (1, 2 or

3), or switch off if no speed was

selected. To turn off the fast speed,

before the end of the 5 minutes,

press button A or button B.

H - OFF lamp button

I - ON lamp button

If the hood fails to operate correctly, briefly

disconnect it from the mains power supply

for almost 5 sec. by pulling out the plug.

Then plug it in again and try once more

before contacting the Technical Assistance

Service.

OO123 I

Filter saturation control devices for

grease filters

This hood is supplied with a device that

notifies the user when the grease filter must

be cleaned or the carbon filter replaced (if

installed).

Upon installation, the saturation control

device for the carbon filter is not activated

(the hood is ready for use in vent mode).

In the event, you would like to install a

carbon filter, activate the saturation control

device by pressing the B and G buttons at

the same time for 3 seconds.

O123

at the start of this procedure, only the F Led

will blink, after 3 seconds have passed, the

C Led will begin to blink, as well to indicate

that the saturation control device for the

carbon filter has been activated.

Grease filter saturation Led

123

The Led marked F flashes to warn you when

the grease filter needs to be cleaned.

Carbon filter saturation Led

123

The Led marked C flashes to indicate carbon

filter needs to be replaced.

Reset for the saturation control

devices for grease and carbon filters

Once the grease filters have been cleaned

or the carbon filter replaced, press the A

button for approximately 3 seconds until you

hear the (beep):

O123

The F led and C led (if active) will stop

blinking.

Maintenance

Before performing any maintenance

operation, disconnect the hood from the

electricity.

Metal grease filter - Fig. 2

The cooker hood is fitted with metal filters.

Remove the metal filter using the handles

designed for this purpose by pulling them

backwards and then downwards.

The metal grease filter lasts forever and

must be washed either by hand or in the

dishwasher (65°C) with suitable detergents.

The grease filters must be washed at

least once a month.

Before refitting the filter ensure that it is

perfectly dry.

Position of filters is interchangeable.

Carbon filter - Fig. 3

This filter dissolves cooking odours.

The carbon filter must never be washed.

It should be changed every 4 months in

normal use.

Fitting the carbon filter

Fit the carbon filter into its housing, by

pushing it backwards and then forwards

and fixing it with the two red buttons B on

the carbon filter.

Dismounting the carbon filter

To dismount the filter, press the two buttons

B and pull it downwards.

Replacing the lamp - Fig. 4

a) Disconnect the hood from the electricity.

b) Remove the blown halogen light bulb

using a screwdriver.

c) Only ever use halogen light bulbs with a

maximum of 20 W.

d) Fit the new light bulb taking care to ensure

its contacts are correctly fitted in the

connector.

If the lighting fails to work, make sure that the

halogen light bulbs have been fitted correctly

before contacting the technical assistance

service!

Cleaning

To clean the outside of the hood use a cloth

moistened with denatured alcohol or neutral

liquid detergents.

Never use products containing abrasive.

Attention

Failure to observe the rules for cleaning the

appliance and changing and cleaning the

filters may cause fires.

Therefore, we recommend observing these

instructions.

Fastening of shelves (Fig. 5)

Fasten the four side supports I to the adjacent

cabinets and place the shelf on the supports.

ELECTROLUX HAUSGERÄTE GMBH

Rennbahnstraße 72-74

60528 Frankfurt

L 850 Ed. 02/97

Juno JDK8460W User manual

Brand: Juno

Model: JDK8460W

Type: User manual

This manual is also suitable for

JDK8460S

Download PDF

report

Juno JDK8460W User manual

This manual is also suitable for

Juno JDK8460W User manual

Related papers

Other documents