Haier HHX1030 User manual

Brand: Haier

Model: HHX1030

Category: Cooker hoods

Type: User manual

User Manual Model

HHX1030

Guide de l’Utilisateur

HHX1030

Manual del Usuario Modelo

HHX1030

Range Hood

Extractor de Aire

Hotte de Cuisiniere

Haier

English

SAFETY PRECAUTIONS

Warning! – To reduce the risk of fire, electric shock, or injury to persons, always

exercise basic safety precautions, including the following:

1. Read all instructions before using the appliance.

2. Use this appliance only for its intended purpose as described in this user manual.

3. Do not use any accessories not recommended by the manufacturer.

4. This unit must be grounded.

5. Do not use this appliance for commercial uses.

6. Do not use this unit with any solid-state speed control device.

7. Installation work and electrical wiring must be done by qualified technicians in

accordance with all applicable codes and standards, including fire-rated

construction.

8. Sufficient air is needed for proper exhausting of gases of fuel burning equipment

through the flue (chimney) to prevent back drafting. Follow the heating

equipment manufacturer’s guideline and safety standards such as those published

by the National Fire Protection Association (NFPA), and the American Society for

Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and local code

authorities.

9. When replacing an existing range hood with your new Haier Range Hood, turn

OFF the electrical power to the existing unit before removal.

10. Before servicing or cleaning the unit, turn the power OFF at the service panel

and if possible, lock the service panel to prevent power from being switched on

accidentally. When the service disconnecting cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

11. Do not repair, replace any part of the appliance or attempt any servicing.

Note: If for any reason this product requires service, we strongly recommend that

a certified technician perform the service.

12. When cutting or drilling into wall or ceiling, be careful not to damage existing

electrical wiring and other hidden utilities.

13. Ducted fans must always be vented to the outdoors.

To reduce the risk of range top grease fires:

1. Always turn the hood ON when cooking at high heat or when cooking flaming

foods.

2. Never leave cooking unattended at high settings. Boilovers cause smoking and

greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

3. Use proper-sized pans that correspond to the size of the stove, and the amount

of food being cooked.

4. Clean ventilation fans frequently. Do not allow grease to accumulate on the fan

or the filter.

English

Thank you for using our Haier product.

This easy-to-use manual will guide you

in getting the best performance from

your Haier Range Hood.

Remember to record the model and

serial number. They are on a label in the

refrigerator.

Model number

Serial number

Date of purchase

Staple your receipt to your manual.

You will need it to obtain warranty service.

To reduce the risk of personal injury in the event of a range top grease fire:

1. NEVER pick up a flaming pan, as you may be injured.

2. DO NOT use water, including wet dishcloths or towels, to put out a fire. A

violent steam explosion may result.

3. Smother flames with a close-fitting lid, metal tray, or cookie sheet. Then turn

OFF the burner. BE CAREFUL TO AVOID BURNS! If the flames are not put out

immediately, evacuate and call the fire department.

4. Use an extinguisher only if:

a) You know that you have a Class ABC extinguisher and you already know

how to use it.

b) The fire is small and contained in the area where it started.

c) The fire department is being called.

d) You can fight the fire with your back to an exit.

CAUTION!

Important – Observe all governing codes and ordinances.

1. For general ventilation use only. Do not use this appliance to exhaust

hazardous or explosive materials and vapors.

2. To reduce the risk of fire, use only metal ductwork.

3. To avoid damage to motor or other components, keep drywall spray,

construction dust, etc. off the power unit.

4. Please read specification label on product for further information and

requirements.

SAVE THESE INSTRUCTIONS for Future Use

English

Accessories

Range Hood Accessories Provided:

1 Range Hood

1 Damper Flap

4 Damper Screws

4 Range Hood Screws

4 Washers

2 Wire Connectors

1 Aluminum Filter

1 Charcoal Filter

1 User Manual

Check to make sure that all parts and accessories are present and in good

condition. If you find that they are not in good condition or are missing, please

contact our customer service department for assistance. Our Toll-Free number

is 1-877-337-3639.

Table Of Contents

PAGE

Safety Precautions ............................................................................................1

Accessories ......................................................................................................3

Installation Preparation......................................................................................4

Selecting Venting Direction ................................................................................5

Cabinet Preparation for Hoods Support..............................................................6

Preparing Electrical Connections ........................................................................6

Preparing Duct Connections ..............................................................................7

Wiring Diagrams..............................................................................................8

Installing Ductwork............................................................................................8

Hood Installation ..............................................................................................9

Use and Care ................................................................................................10

Troubleshooting ..............................................................................................11

Warranty Information......................................................................................12

English

Installation Preparation

To install this range hood, you will need the following tools and materials:

Note: This procedure will require 2 people for easier installation.

Tools Needed for Installation

• Drill

• 1/8” Drill bit for drilling pilot holes

• 1-1/4” Wood bit for drilling electrical wiring access hole

• Phillips head screwdriver

• Flat-head screwdriver

• Pliers

• Pencil, rule and level for marking range hood location

• Hand saw or jig saw for cutting the wall or cabinet openings

• Duct tape

• Electrical tape

• Connector Clamp

General Preparation

Caution! Please be sure to turn the electrical power switch OFF before beginning

the installation.

1. Remove the range hood from the carton.

2. Lay the range hood upside down on a table covered with either cardboard or

paper to prevent scratching the hood or table.

3. Unscrew the lamp cover with a Phillips head screwdriver.

4. Remove the lamp cover.

5. Install one 40 Watt light bulb.

6. Replace the lamp cover and the screws.

English

Selecting the Venting Direction

The range hood can be used for either horizontal, vertical or ductless air discharge.

For the best performance, use the shortest possible ducting path and the least

amount of elbows when discharging horizontally or vertically.

Vertical Discharge – Vertical discharge is the most common method of hood

installation. If your kitchen has an attic space above, the ducting may be run

through the cupboard and the attic to a roof cap. Use a 7” round duct (not

included).

Another option, if your kitchen has a soffit above the cabinet, is to run the duct up

into the soffit and then discharge the air horizontally through the outside wall to a

wall cap.

Horizontal Discharge - If the range is located against an outside wall, then

horizontal discharging is ideal, provided there are no obstructions such as wall

joists or places where openings are difficult to make.

If a wall cap is used directly off the back of the hood, special care must be taken to

ensure that the damper in the damper/duct connector on the hood and the damper

in the wall cap do not interfere with each other when the range hood is operating.

This could result in either inadequate air delivery or back drafts. If this condition

exists, remove the hood damper flap. Sometimes when using a wall cap, it is easier

to duct vertically and than to use an elbow.

Ductless – In ductless installations, air is vented back into the kitchen through the

opening in the range hood grille. If you do not anticipate heavy cooking, this

method may be preferable. Ductless installation requires the use of a charcoal

filters (included) to remove odors, which should be replaced at regular intervals

depending on use. Check with your local retailer or dealer for replacements.

Note: This filter is not dishwasher safe!

English

For model HHX1030 you must remove the vent cover from the slots on the front of

the range hood. Save the vent cover for possible future use.

Cabinet Preparation for Hood Support

Mount the hood so that the bottom of the hood is between 24”-30” above the

stovetop.

Warning! When cutting or drilling into wall or cabinet, be careful not to cut

existing electrical wiring.

1. If the bottom of the cabinet is recessed above the bottom of the cabinet

door, then it is necessary to install wood strips on each side of the

recessed area on the bottom of the cabinet where the range hood will

be mounted. The wood strips should line up with the 4 keyhole slots on

the top of the range hood. Fasten the wood strips with wood screws

about 3” in from each end.

Note: The thickness of the wood strips should be slightly more than the

recessed dimension. The length should be cut to size.

2. Measure and mark the electrical wiring opening in the wall or the

cabinet. If the hood is to be vented, also mark and measure the duct

opening in the wall or cabinet.

Preparation of Electrical Connections

Note: If replacing an existing hood, the electrical cable may need to be re-routed to

the desired position.

1. Determine the location of the electrical cable to connect to the range

hood.

fig. 1

English

2. Remove the electrical knockout on the back or top of the range hood

and install a standard electrical cable clamp.

3. Transfer the location of the range hood electrical knockout to either the

bottom of the cabinet or the wall. Drill or cut a hole in the adjoining

surface to make room for the electrical cable clamp.

Preparation for Duct Connection

1. Remove the appropriate ducting knockout by inserting a screwdriver under one

end and prying it up. Then snip or break the attachment points.

2. Install the damper assembly to the range hood with the 2 screws supplied.

3. If discharge is vertical through a rectangular duct, remove the knockout sections

D, B and E only.

4. If the vertical discharge is through a 7” round duct, remove knockout sections

“A” and “B” and “C” only.

Note: Section “D” and “E” remain with the hood.

5. Mount the round collar (E22A -not supplied) over the opening on the hood by

using 3 shorter screws. Allow the bottom edge of the 7” duct to be inserted into

the collar.

fig. 2

fig. 3

English

Wiring Diagrams

Installing Ductwork

Your new range hood will operate at the highest efficiency if the number of elbow

and the length of the duct are kept to a minimum. The back draft damper flap

attached to the damper frame assembly, which is supplied with the hood, does not

impede airflow significantly. You may leave this in place even if you install a wall

or roof cap with another back draft damper.

English

Hood Installation

Note: All wiring installation must comply with local and national electrical code

regulations.

1. Lift the hood into position and guide the electrical cable through the electrical

cable clamp on the hood.

2. Insert the 4 wood screws from the bottom and securely fasten.

3. Secure the electrical cable in the cable clamp while allowing sufficient length in

the hood to connect the field wires to the hood wires.

4. Make the electrical connections using screw-on wire connectors. Attache the

black wires together and then the white wires together and then the green or

bare wire to the green grounding screw in the hood. Replace the wiring

compartment cover.

Caution! All wiring installation must comply with local and national electrical code

regulations.

5. Attach ductwork and use duct tape to seal all joints.

6. After turning all range hood switches to the OFF position, turn the power ON

and test your installation.

English

Use and Care

Aluminum Filter

For highest efficiency, this filter should be removed and cleaned periodically. Soak

the filter in hot water and mild soap or detergent. Rinse thoroughly and repeat if

necessary. The aluminum filter may be cleaned in the dishwasher. Heavy grease

buildup may not be cleaned easily, thus the filter may need to be replaced.

Charcoal Filter

Inspect this filter periodically. This filter cannot be cleaned and must be replaced

when it becomes saturated. Check with your local retailer or dealer to purchase.

Light Bulb

Do not use light bulbs that are brighter than 40 watts.

Exterior Surface

Wipe the range hood exterior with a soft cloth and a mild detergent suitable for

painted surfaces. Do NOT use abrasive materials such as steel wool pads or

scouring powders.

Repair or Replacement Parts

Warning! Disconnect range hood from the electrical power supply before servicing.

All parts may be obtained from service centers authorized by Haier, or may be

ordered directly from Haier. When ordering parts, please specify the range hood

model number on the rating label, which is located on the inside of the range hood.

English

Trouble Shooting

Fan does not turn on (but light turns on).

This is probably due to either a defective fan switch or a burned-out fan motor.

Both can be replaced without removing the range hood from the wall or cabinet.

Use an ohm meter to determine which component is not working. If the ohm meter

reads that the fan switch has 0 ohms of resistance, then it is the motor that needs to

be replaced. If it reads anything other than zero, then the switch must be replaced.

Fan only runs at one speed.

Please see instructions above for troubleshooting when your fan does not turn on

(but light turns on).

Fan circulates air, but does not vent outside.

If air is blowing through the front vent openings, then your range hood has been

installed for ductless operation. In order to convert the system to vent outside, a

technician must install metal ductwork from the range hood through either an

outside wall or the roof.

If air is not blowing from the front vent openings, check inside the cabinet above the

range hood. If you see a metal duct leading away from the vent hood, then you

have a system that vents to the outdoors. If you do not see a duct, your unit may be

venting through the back wall.

Light does not turn on (but fan turns on).

This could be because the bulb has burned out. Try replacing the light bulb. If the

light still does not work, either the light switch or the lamp-holder socket is defective.

Both can be replaced without removing the range hood from the wall or cabinet.

Night light does not turn on.

Please see above instructions for troubleshooting when the light that does not turn

on (but fan turns on).

Range hood does not turn on at all.

First, check for a tripped circuit breaker or a blown fuse, since the range hood is

wired directly to your household electrical system.

NOTE: All work must be performed by a qualified and licensed technician!

English

This warranty covers all defects in

workmanship or materials for:

The mechanical and electrical parts (including

labor costs) contained in this Haier product, for

a period of 12 months, from the date of

purchase (for commercial or rental applications,

the warranty is 90 days).

You must keep and be able to provide your

original sales receipt as proof of the date of

purchase.

Who is covered?

The original retail purchaser of this Haier

product.

What will be done?

Haier will repair or replace, in your home, any

mechanical or electrical part, which proves

defective, in normal household use for a period

of 12 months.

How can you get service?

1. Contact your nearest Haier authorized

Service Center. For the name of the Service

Center nearest you, contact Haier at

(877) 337-3639.

2. All service must be performed by an

authorized Haier Service Center.

THIS WARRANTY COVERS UNITS WITHIN THE

CONTINENTAL UNITED STATES, CANADA AND

PUERTO RICO.

THIS WARRANTY DOES NOT COVER:

• Damages from improper installation

• Damages from shipping

• Damages from misuse, abuse, accident,

alteration, lack of proper care and

maintenance

• Damages from service by persons other than

an authorized dealer or service center

• Labor, service, transportation and shipping

charges for the removal of defective parts and

for installation of a replacement part, beyond

the initial 12-month period.

THIS LIMITED WARRANTY IS GIVEN IN LIEU OF

ALL OTHER WARRANTIES, EXPRESSED OR

IMPLIED, INCLUDING THE WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE.

The remedy provided in this warranty is

exclusive and is granted in lieu of all other

remedies. This warranty does not cover

incidental or consequential damages. Some

states do not allow the exclusion of incidental or

consequential damages, so this limitation may

not apply to you. Some states do not allow

limitations on how long an implied warranty

lasts, so this limitation may not apply to you.

This warranty gives you specific legal rights, and

you may also have other rights, which vary from

state to state.

Limited Warranty

Francias

Consignes de Securite

Avertissement! Pour reduire le risque d’incendie, d’un shoc electrique, des

blessures personelles, exercez toujours les precautions de securite fondamentales

y compris les suivants.

1. Lisez toutes les instructions avant d’utiliser cet appareil

2. Utilisez cet appareil uniquement pour l’usage auquel il est destine comme indique

dans ce manuel d’utilisation

3. N’utilisez aucun accessoire qui n’est pas recommande par le fabricant

4. Cet unite doit etre mis a terre

5. N’employez pas cet appareil pour les usages commerciaux

6. N’employez pas cet unite avec aucun dispositif de commande de vitesse a semi-

conducteurs.

7. L’installation et le cablage electrique doivent etre faits par des techniciens

qualifies selon tous les codes et normes y compris la construction du feu evaluee

8. Assez d’air est necessaire pour epuiser le gaz de carburant brulant a travers le

conduit (cheminee) pour eviter le courant d’air

9. Quand vous remplacez une hotte avec une autre nouvelle hotte Haier, eteignez

le courant de l’unite existant avant le remplacement.

10. Avant d’entretenir ou de nettoyer l’unite, eteignez le courant de l’unite sur le

paneau de service et si possible, serrurez le panneau de service pour empecher

a la puissance de s’allumer par accident

11. Ne pas reparer, remplacer n’importe quelle partie de l’appareil et ne pas tenter

de fixer l’appareil vous meme.

Note: Si pour n’importe quelle raison cet appareil doit etre repare, on

recommande avec force qu’un technicien certifie execute le service

12. En coupant ou percant le mur ou plafond, faites attention a ne pas

endommager le cable electrique existant ou autres utilites caches.

13. Les conduits des ventilateurs doivent etre toujours ventilles vers le dehors.

Pour reduire le risque d’incendies de graisse:

1. Mettez toujours la hotte en marche en cuisinant a une chaleur elevee ou en

faisant cuire les nourritures flamboyantes.

2. Ne laissez jamais une cuisson a une chaleur elevee sans surveillance . Les

debordements causent de la fumee et les renversements graisseux peuvent causer

une incendie. Chauffez l’huile lentement sous un montage lent ou moyen.

3. Utilisez une casserole correspondante a la taille de la cuisiniere et a la quantite

de la nourriture qui doit etre cuisine

4. Nettoyez les ventilateurs de ventilation frequemment. Ne permettez pas a la

graisse de s’accumuler sur le ventilateur ou le filtre.

Francias

Pour reduire le risque d’une blessure au cas d’une incendie de graisse sur la

cuisiniere:

1. Ne relevez jamais une casserole flamboyante, vous pouvez vous blesser.

2. N’utilisez jamais de l’eau, y compris des serviettes mouillees pour eteindre une

incendie. Une explosion de vapeur violente peut resulter.

3. Etouffez le feu a l’aide d’un couvercle , d’un plateau en metal , puis eteignez les

bruleurs. Soyez prudents.. Evitez les brulures!!! Si les flammes ne s’eteignent pas

immediatement, evacuez vite et appelez les pompiers.

4. Utilisez un extincteur seulement si:

a ) Vous savez que vous avez un extincteur ABC et vous savez comment

l’utiliser.

b) L’incendie est petite et contenue dans le meme endroit ou ca a commencee.

c) Les pompiers ont ete appeles

d) Vous pouvez combattre le feu avec votre dos vers la sortie

Attention!!!!

Important. Observez tous les codes et ordennances regissants.

1. Pour une utilisation de ventilation generale seulement

2. Pour reduire le risque d’une incendie utilisez seulement des conduits en metal.

3. Pour eviter d’endommager le moteur ou autres composants , maintenez le jet de

cloison seche, la poussiere de construction,etc… hors de l’unite de puissance

4. Priere de lire les etiquettes de specification sur le produit pour des amples

d’information et les conditions.

Conservez ces Instructions

Merci d’avoir achete un produit de

Haier. Ce manuel facile a consulter

vous aidera a utiliser au mieu votre

hotte cuisiniere Haier

N’oubliez pas d’enregistrer les numeros

de model et serie. Ils sont sur une

etiquette a l’arriere de votre unite.

Numéro de modèle

Numéro de série

Date d’achat

Agrafer le ticket de caisse au guide. Celui-ci doit être produit

pour tout dépannage sous garantie. .

Francias

Table Des Matieres

Page

Consignes de Securite ....................................................................................13

Accessoires ....................................................................................................15

Preparation pour l’installation..........................................................................16

Choix des directions de ventilation ..................................................................17

Preparation du placard pour le support de la hotte ..........................................18

Preparation des connections electriques............................................................18

Preparation des connections des canalisations ..................................................19

Diagrammes de cablage ................................................................................20

Installation des canalisations............................................................................20

Installation de la hotte ....................................................................................21

Utulisation et Entretien ....................................................................................21

Depannage ....................................................................................................22

Garantie ........................................................................................................23

Accessoires

Les accessoires de la hotte fournis

1 Une hotte cuisiniere

1 Un armotisseur

4 Vis d’armotisseur

4 Vis pour la hotte

4 Rondelles

2 Fils connecteurs

1 Filtre en aluminium

1 Filtre en charbon

1 Manuel d’utilisation

Assurez vous que toutes les parties et accessoires existent et en bonne condition. Si

les pieces manquent ou sont endommagees, contactez notre departement de service

pou n’importe quelle aide. Numero gratuit 1-877-337-3639

Francias

Preparations pour l’installation

Pour installer la Hotte, vous aurez besoin des outils et materiaux suivants.

Note: Ce procedes exigera 2 personnes pour une installation plus facile.

Outils dont vous aurez besoin pour l’installation

• Une perceuse

• Une perceuse meche de 1/8” pour forer des trous pilotes

• Une perceuse en bois de 1-1/4” pour forer l’ouverture d’acces electrique de

cablage

• Un tournevis Phillips

• Un tournevis plat

• Des pinces

• Un crayon, une regle , un nivel pour marquer la location de la hotte

• Une scie a main ou gabarit pour couper l’ouverture du mur ou du placard

• Une bande adhesive

• Une bande electrique

• Bride de connecteur

Preparation Generale:

Attention: Avant de commencer l’installation, priere de fermer tous les courants

electriques.

1. Enlevez la hotte de la boite en carton

2. Placez la hotte sens dessous sur une table couverte en papier ou carton pour

eviter des rayures sur la table ou la hotte

3. Desserez le couvert de la lampe a l’aide d’un tournevis Phillips

4. Enlevez le couvert de la lampe

5. Installez une lampe de 40 Watts.

6. Replacez le couvert et vis de la lampe.

Francias

Choisir la direction de ventilation

La hotte peut etre utilisee pour un discharge d’air horizontale, verticale ou sans

conduits. Pour le meilleur resultat, utilisez le plus court passage de conduit et la

moindre quantitee des coudes pour un discharge horizontal ou vertical.

Dechargement vertical: Le dechargement vertical est la methode la plus commune

pour l’installation de hotte . Si votre cuisine a un grenier au dessus, les conduits

peuvent etre installes a travers le grenier et le compartiment jusqu’au toit. Utilisez

un conduit de 7” (pas founi )

Un autre choix, si votre cuisine a une ouverture au dessus du placard , parcourez

les conduits jusqu’a l’ouverture puis dechargez l’air horizontalement a travers le

mur exterieur jusqu’au cap du mur.

Dechargement honrizontal: Si la cuisiniere est installee contre un mur exterieur , un

dechargement horizontal est ideal , vue qu’il n’y a aucune obstruction comme une

solive de mur ou des endroits ou les ouvertures sont difficiles a faire.

Si la casquette du mur est utilisee directement au dos de la hotte, un soin special

doit etre pris pour s’assurer que l’armortisseur du connecteur du tuyau de

l’armotisseur et l’armotisseur dans la casquette n’interferent pas l’une avec l’autre

quand la hotte est en fonction. Ceci peut resulter d’une livraison d’air inadequate ou

des retours de courants d’air. Ci cette condition existe, soutirez le rabat

d’armotisseur de la hotte. Parfois en utilisant une casquette de mur, c’est plus facile

de decharger verticalement d’utiliser un coude.

Sans conduit : Dans les installations sans conduits, l’air est ventille de nouveau a la

cuisine a travers l’ouverture de la grille de la hotte. Si vous n’anticipez pas une

grande cuisson, cette methode est plus preferable. Installation sans conduits, exige

l’utilisation des filtres de charbon (fournis) pour enlever les odeurs qui doit etre

remplaces regulierement dependant de l’usage. Verifiez avec votre negociant ou

detaillant local pour le remplacement.

Note: Ce filtre ne doit pas etre utilise dans le lave-vaisselle.

Francias

Pour le model HHX1030 il faut enlever le couvert du ventilateur des entailles du

devant de la hotte. Gardez le couvert du vetilateur pour le future.

Preparation du placard pour supporter la hotte.

Montez la hotte de facon que le bas de la hotte est entre 24”-30” au dessus de la

cuisiniere.

Precautions! Quand vous coupez ou ferrez dans le placard ou mur, faites attention

a ne pas couper des fils electriques existants.

1. Si le bas du placard est encastre au dessus du bas de la porte du placard,

c’est necessaire d’installer des bandes de bois de chaque cote du secteur

encastre sur le bas du placard ou la hotte sera montee. Les bandes de bois

doivent etre alignees avec les 4trous de serrure des entailles situes au

sommet de la hotte. Attachez les bandes de bois avec les vis en bois environ

3” de chaque fin.

Note: l’epaisseur de la bande de bois doit etre un tout petit peu plus

epaisse que les dimensions encastrees. La longueur doit etre de meme taille.

2. Mesurez et marquez les ouvertures du fil electrique sur le mur ou le

placard. Si la hotte doit etre ventillee, mesurez et marquez l’ouverture du

conduit sur le mur ou le placard.

Preparation des connections electriques

Note: Si vous remplacez une hotte qui existait, le cable electrique peut avoir besoin

d’etre mis en deroute dans les positions desirees.

1. Determinez l’emplacement du cable electrique pour connecter la hotte.

fig. 1

Francias

2. Enlevez le knockout du sommet ou dos de la hotte et installez une lampe de cable

electrique standarde.

3. Transferez l’emplacement du knockout electrique de la hotte au bas du mur ou du

placard. Percez ou coupez un trou sur la surface attenante pour faire place a la

lampe de cable electrique

Preparations pour la connections des conduits.

1. Enlevez le knockout approprie du conduit en inserant un tournevis sous une fin

et forcez vers le haut. Puis cassez ou detaches les points d’attachement.

2. Installez l’assemeblee d’artomiseur a la hotte avec les 2 vis fournis.

3. Si le dechargement est vertical a travers un conduit rectangulaire, enlevez les

sections du knockout “ D ” “ B ” et “ E ” seulement,

4. Si le dechargement vertical est a travers un conduit de 7 ” enlevez les sections du

knockout “ A” “B ” et “ C ” seulement.

Note: Les sections “D ” et “E” resteront avec la hotte.

5. Montez le col rond ( E22A-pas fourni ) sous l’ouverture sur la hotte en utilisant 3

courts vis. Permettez au bord inferieur du conduit de 7” d’etre inserer dans le col.

fig. 2

fig. 3

Page is loading ...

Haier HHX1030 User manual

Brand: Haier

Model: HHX1030

Category: Cooker hoods

Type: User manual

Download PDF

report

in other languages

français: Haier HHX1030 Manuel utilisateur
español: Haier HHX1030 Manual de usuario

Haier HHX1030 User manual

Haier HHX1030 User manual

in other languages

Related papers

Other documents