Miller HEAVY DUTY CROSS SLIDES provide horizontal or vertical movement of welding equipment and can be used in various industrial and manufacturing applications. They are designed to handle heavy loads and offer precise positioning for welding tasks. The cross slides feature a sturdy construction with a weight capacity of 250 lbs at a distance of 12 inches from the carrier face plate. They come with a 6-3/4-inch square mounting hole pattern, allowing for mounting one cross slide on top of another to achieve X-Y movement.
Miller HEAVY DUTY CROSS SLIDES provide horizontal or vertical movement of welding equipment and can be used in various industrial and manufacturing applications. They are designed to handle heavy loads and offer precise positioning for welding tasks. The cross slides feature a sturdy construction with a weight capacity of 250 lbs at a distance of 12 inches from the carrier face plate. They come with a 6-3/4-inch square mounting hole pattern, allowing for mounting one cross slide on top of another to achieve X-Y movement.
OWNER’S MANUAL
© 2010 Miller Electric Mfg. Co.
OM-239 596C
2010−04
For Heavy Duty Cross Slides
1. Safety Symbol Definitions
DANGER! − Indicates a hazardous situation which, if not
avoided, will result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained
in the text.
Beware of electric shock from wiring. Disconnect input
power before installing this kit. Reinstall all panels and
covers.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible ha-
zards are shown in the adjoining symbols or explained in
the text.
Falling equipment can cause injury and unit damage.
Never put any body part under unit while lifting. Lifting
forks must extend out opposite side of base. Lift unit
using proper equipment.
NOTICE
Indicates statements not related to personal injury.
Indicates special instructions.
Wear safety glasses with side shields.
Proposition 65 Warnings
Welding or cutting equipment produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in
some cases, cancer. (California Health & Safety Code Section 25249.5 et seq.)
This product contains chemicals, including lead, known to the state of California to cause cancer, birth defects, or other reproductive harm.
Wash hands after use.
2. Description
The cross slide design provides horizontal or vertical movement of welding equipment. Two cross slides may be installed to provide X-Y (both horizont-
al and vertical) movement of welding equipment.
3. Specifications
Total Slide Movement Overall Dimensions Weight
8 in. (204mm)
4−3/8 in. x 8 in. x 17−7/8 in.
(111 mm x 204 mm x 454 mm)
17 lbs 6 oz
(7.9 kg)
Ref. 805 306-A
! Turn off wire feeder and weld-
ing power source, and discon-
nect input power before work-
ing on unit.
! Disconnect and lockout/tagout
input power before working on
unit.
1 Two Units Mounted Together
. Weld spatter, dirt and dust can af-
fect cross slide operation. Mount
in a suitable location.
The 6-3/4 in. (171 mm) square mount-
ing hole pattern in the cross slide car-
rier permits mounting one cross slide
on top of another to provide X-Y
movement.
Install welding equipment on carrier
plate using customer supplied 3/8-16
in. cap screws.
. Mounting screws must not
interfere with carrier travel.
1
4. Installation
OM-239 596 Page 2
5. Bearing Adjustment Procedure
. Using callout items from the parts list to perform the following procedure.
The guide wheels are fastened to the wheel plate with special mounting bolts. These bolts pass through shouldered bushings that are inserted into
the guide wheel. There are two types of bushings; the fixed or concentric (callout item 12), and the adjustable or eccentric (callout item 13). The eccent-
ric bushing has hexagonal flats.
Pre-Load Guide Wheel Adjustment:
1. Check concentric guide wheel mounting bolts for tightness.
2. Loosen the eccentric guide wheel mounting bolt just enough to allow rotation of the eccentric bushing. Make the following adjustments in small
increments.
3. Rotate the eccentric bushing to a point where the guide wheels contact the track.
4. Hold the guide wheel firmly between your fingers and move the wheel plate along the track. At the same time, rotate the bushing to a point where
the guide wheel does not skid on the track. Tighten the wheel bolt snugly so that this temporary adjustment holds.
5. Repeat this procedure on the second eccentric guide wheel.
6. A proper adjustment is achieved by repeating steps 4 and 5 until a uniform resistance to motion is attained by “feel” along the entire track.
7. Fully tighten the eccentric wheel bolts to fix both adjustments.
. Both eccentric wheels need to be adjusted prior to performing this final tightening to avoid binding of the carriage.
8. Apply wicking thread locker to wheel bolt threads from top of wheel plate. Use loctite 290 or equivalent.
Ref. 805 308-A
! Incorrect loading of heavy
duty cross slide can cause
personal injury and equip-
ment damage.
1 Load Weight (Center Of Mass)
2 Distance
3 Carrier Face Plate
4 Bottom Pan
Loading Safety Check:
S Estimate combined weight of all
accessories and distance of center
mass from carrier face plate.
S Loading condition must fall within
rating of 250 lbs at 12 in. distance.
S Adjust weight/distance if neces-
sary.
2
3
6. Loading Heavy Duty Cross Slide
4
1
7. Routine Maintenance
. Maintain more often
during severe conditions.
! Disconnect and lockout/tagout
power before maintaining.
n = Check Reference
Every
6
Months
Section 8.
n Lubricate Parts
OM−239 596 Page 3
8. Parts List
805 307-A
. Every six months clean and
apply a light lubricant, such as
SAE 20 oil to the drive screw
and nut (list items 7and 8).
. Hardware is common and
not available unless listed.
10
11
12
13
14
1
2
3
5
6
7
8
9
4
Figure 8-1. Complete Assembly
OM-239 596 Page 4
Description
Part
No.
Dia.
Mkgs.
Item
No.
Figure 8-1. Complete Assembly
Quantity
1 238 232 Plate, Mtg 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 238 225 Handle, Balanced (Machined) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 198 505 Key, Stl .125 X .125 X .750 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 238 219 Plate, End 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 238 223 Bearing, Ball Rdl Sgl Row .375 X 1.125 X .375 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 238 220 Plate, Stop 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 238 221 Shaft, Drive Cross Slide 3/4-6 Acme 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 238 222 Nut, Acme 3/4-6 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 238 224 Rail, Guide V Size 3 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 238 240 Plate, Mtg Bearing 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 238 242 Plate, Acme Nut Adapter 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 238 243 Wheel, Guide Integral Bushing Centered 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13 238 244 Wheel, Guide Integral Bushing Eccentric 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14 238 217 Plate, Base 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
BE SURE TO PROVIDE MODEL AND STYLE NUMBER WHEN ORDERING REPLACEMENT PARTS.
-
1
-
2
-
3
-
4
Miller HEAVY DUTY CROSS SLIDES Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Miller HEAVY DUTY CROSS SLIDES provide horizontal or vertical movement of welding equipment and can be used in various industrial and manufacturing applications. They are designed to handle heavy loads and offer precise positioning for welding tasks. The cross slides feature a sturdy construction with a weight capacity of 250 lbs at a distance of 12 inches from the carrier face plate. They come with a 6-3/4-inch square mounting hole pattern, allowing for mounting one cross slide on top of another to achieve X-Y movement.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
JET 414474 User manual
-
-
WMH Tool Group J-7040M-4 Owner's manual
-
-
-
Kutzall DW412X120 Installation guide
-
Grizzly G9744Z Owner's manual
-
ESAB A2 Multitrac User manual
-
Grizzly Industrial G0811 User guide
-
