2. Computers & electronics
  3. Software
  4. Operating systems
  5. Moxa
  6. NPort 5200A Series
NPort 5200A Series

Moxa NPort 5200A Series User manual

  • Hello! I am an AI chatbot trained to assist you with the Moxa NPort 5200A Series User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Moxa CLI Configuration Tool User’s
Manual
Edition 2.0, December 2018
www.moxa.com/product
© 2018 Moxa Inc. All rights reserved.
Moxa CLI Configuration Tool User’s
Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance
with the terms of that agreement.
Copyright Notice
© 2018 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not
limited to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to
the products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility
for its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Toll
-free: 1-888-669-2872
Tel:
+1-714-528-6777
Fax:
+1-714-528-6778
Moxa China (Shanghai office)
Toll
-free: 800-820-5036
Tel:
+86-21-5258-9955
Fax:
+86-21-5258-5505
Moxa Europe
Tel:
+49-89-3 70 03 99-0
Fax:
+49-89-3 70 03 99-99
Moxa Asia
-Pacific
Tel:
+886-2-8919-1230
Fax:
+886-2-8919-1231
Moxa India
Tel:
+91-80-4172-9088
Fax:
+91-80-4132-1045
Table of Contents
1. Introduction ...................................................................................................................................... 1-1
System Requirements ......................................................................................................................... 1-2
Supported Platforms .................................................................................................................... 1-2
Supported Models ........................................................................................................................ 1-2
Installing MCC_Tool on Windows .......................................................................................................... 1-2
Installing MCC_Tool on Linux ............................................................................................................... 1-6
2. Getting Started ................................................................................................................................. 2-1
Overview ........................................................................................................................................... 2-2
Supported Functions and Command Structure ................................................................................ 2-2
Device List ................................................................................................................................. 2-3
Support Product Series ................................................................................................................ 2-3
Function Support Table ................................................................................................................ 2-3
Usage Examples of Supported Functions ................................................................................................ 2-4
Report Firmware Versions............................................................................................................. 2-4
Upgrade Firmware and Restart the Device ...................................................................................... 2-5
Export/Import Device’s Configuration ............................................................................................ 2-5
Restart Specific Serial Ports or the Whole Devices ........................................................................... 2-7
Change User’s Password on the Device .......................................................................................... 2-8
Show Support Model List .............................................................................................................. 2-9
Update Plugin ............................................................................................................................. 2-9
Error Code Explanation ................................................................................................................ 2-9
1
1. Introduction
Moxa CLI Configuration Tool (MCC_Tool) is a command line tool that provides the following functions to
manage field devices.
• Report firmware versions
• Upgrade firmware
• Import/export configuration files
• Password changes
Management tasks can be performed according to a desired scale (1 for single device or 1 for multiple
devices) and across different subnet networks.
The following topics are covered in this chapter:
System Requirements
Supported Platforms
Supported Models
Installing MCC_Tool on Windows
Installing MCC_Tool on Linux
Moxa CLI Configuration Tool Introduction
1-2
System Requirements
Supported Platforms
• Windows 7 and later versions.
• Linux kernel 2.6 and later versions.
Supported Models
• NPort 5100A Series: 5110A, 5130A, 5150A, P5150A (Firmware v1.4 and later versions)
• NPort 5200A Series: 5210A, 5230A, 5250A (Firmware v1.4 and later versions)
• NPort IA5000A Series: IA5150A, IA5150AI, IA5250A, IA5250AI (Firmware v1.3 and later versions);
IA5450A, IA5450AI (Firmware 1.4 and later versions)
• NPort 5000A-M12 Series: 5150AI-M12, 5250AI-M12, 5450AI-M12 (Firmware v1.3 and later versions)
• NPort 6000 Series: 6150, 6250, 6250-M-SC, 6250-S-SC, 6450, 6610-8, 6610-16, 6610-32, 6650-8,
6650-16, 6650-32 (Firmware v1.6 and later versions)
• MGate MB3x80 Series: MB3180, MB3280, MB3480 (Firmware v2.0 and later versions)
• MGate MB3x70 Series: MB3170, MB3170I, MB3170-M-SC, MB3170-M-ST, MB3170-S-SC, MB3170I-M-
SC, MB3170I-S-SC, MB3270, MB3270I (Firmware v3.0 and later versions)
• MGate 3660 Series: MB3660-8-AC, MB3660-8-2AC, MB3660-8-DC, MB3660-8-2DC, MB3660I-8-2AC,
MB3660-8-J-2AC, MB3660-16-AC, MB3660I-16-AC, MB3660-16-2AC, MB3660-16-J-2AC, MB3660I-16-
2AC, MB3660-16-DC, MB3660-16-2DC, MB3660I-8-AC (Firmware v2.0 and later versions)
• ioLogik E1200 Series: E1210, E1211, E1212, E1213, E1214, E1240, E1241, E1242, E1260, E1262
(Firmware v2.4 and later versions)
• ioThinx 4500 Series: ioThinx 4510, ioThinx 4510-T (Firmware v1.0 and later versions)
Installing MCC_Tool on Windows
Step 1: Download MCC_Tool for Windows on URL:
https://www.moxa.com/support/download.aspx?type=support&id=15923
. Unzip the folder and execute
the .exe file. The setup wizard will pop up to direct you to the next steps.
Step 2: Select destination location of where MCC_Tool should be installed.
Moxa CLI Configuration Tool Introduction
1-3
Step 3: Select Start Menu Folder to create the program’s shortcuts.
Step 4: Select Additional Tasks if any and click Next.
Moxa CLI Configuration Tool Introduction
1-4
Moxa CLI Configuration Tool Introduction
1-5
Step 5: Confirm previous selection and prepare to install.
Step 6: Complete setup and check Launch mcc_tool if you want to use MCC_Tool after exiting the setup
wizard.
Moxa CLI Configuration Tool Introduction
1-6
Step 7: Use –h command to prompt help information.
Installing MCC_Tool on Linux
Step 1: Download MCC_Tool for Linux on URL:
https://www.moxa.com/support/download.aspx?type=support&id=15925
(Linux x86) and
https://www.moxa.com/support/download.aspx?type=support&id=15924 (Linux x64). Versions for x86 and
x64 OS are available.
Step 2: Access the location where you save the downloaded file and unzip it. For example:
moxa@moxa-virtual-machine:~$ cd Desktop/
moxa@moxa-virtual-machine:~/Desktop$ tar -xvzf
mcc_tool_x64_ver1.0_build_17111618.tar.gz
mcc_tool_x64_ver1.0_build_17111618/
mcc_tool_x64_ver1.0_build_17111618/dsci_mcc.so
mcc_tool_x64_ver1.0_build_17111618/mxio_mcc.so
mcc_tool_x64_ver1.0_build_17111618/mcc_tool
mcc_tool_x64_ver1.0_build_17111618/mgci_mcc.so
moxa@moxa-virtual-machine:~/Desktop$ cd mcc_tool_x64_ver1.0_build_17111618/
Moxa CLI Configuration Tool Introduction
1-7
Step 3: Execute MCC_Tool in the unzipped folder and use –h command to get all the available functions
and option commands of the tool.
moxa@moxa-virtual-
machine:~/Desktop/mcc_tool_x64_ver1.0_build_17111618$ ./mcc_tool -h
MCC_Tool ver1.0 Copyright: Moxa Inc.
Usage: ./mcc_tool [function] [options]
Function:
-fw: Execute "Firmware related" action.
-cfg: Execute "Configuration related" action.
-pw: Execute "Password related" action.
-re: Execute "Restart related" action.
-ver: Show mcc library version.
-help: Display version of MCC_Tool and help information.
Options:
-r: Report firmware version.
-up: Upgrade firmware.
-ex: Export the configuration file.
-im: Import the configuration file.
-ch: Change password.
-de: Restart device.
-sp: Restart port.
-i: Device IP address.
-il: IP address list containing 1 IP address per line.
-d: Device list.
-f: File to be imported or upgraded.
-nd: The Device list with new password settings.
-u: Device's user account for login.
-p: Device's password for login.
-npw: The new password for the specific user.
-dk: Secret key for import/export configuration.
-ps: Specific serial ports to be restarted.
-o: Output file name.
-l: Export result log file.
-n: Keep network settings for configuration import.
-nr: Don't reboot device after finishing executing command.
-print: Print process message for upgrade firmware command.
-t: STimeout(sec).
** NOTICE **
If devices can't be found, you can try again with root privilege.
moxa@moxa-virtual-machine:~/Desktop/mcc_tool_x64_ver1.0_build_17111618$
2
2. Getting Started
This chapter covers what functions are supported by MCC_Tool and how users could use a combination of
main and optional functions to manage Moxa’s edge devices.
The following topics are covered in this chapter:
Overview
Supported Functions and Command Structure
Device List
Support Product Series
Function Support Table
Usage Examples of Supported Functions
Report Firmware Versions
Upgrade Firmware and Restart the Device
Export/Import Device’s Configuration
Restart Specific Serial Ports or the Whole Devices
Change User’s Password on the Device
Show Support Model List
Update Plugin
Error Code Explanation
Moxa CLI Configuration Tool Getting Started
2-2
Overview
Supported Functions and Command Structure
Users will be able to achieve the following tasks by executing a set of command lines.
1. Report firmware version through a device’s IP address or a range of devices specified by IP addresses.
2. Upgrade firmware to a device through a device’s IP address or a range of devices specified by IP
addresses.
3. Export/Import device’s configuration through an IP address and or a range of devices specified by IP
addresses.
4. Restart command for:
4.1. Restart a list of specific ports of multiple devices
4.2. Restart a device through a device’s IP address or a range of devices specified by IP addresses.
5. Change password for an existing user of a device through the device’s IP address or a range of devices
specified by IP addresses.
NOTE
Due to model and firmware differences,
the following functions may NOT work:
1.
Restart multiple ports of a device
2.
Change the password for an existing user (expect the user ”admin”)
3.
Export configuration file with pre-shared key parameters
You may refer to page 2
-3 for Function Support Table to learn more details.
The main functions are defined as below:
Command Function
Execute "Firmware related" action.
Execute "Configuration related" action.
Execute "Password related" action.
Execute "Restart related" action.
Main functions must be used in conjunction with optional commands in order to perform management tasks.
Optional commands are listed in the table below:
Command Function
Report firmware version.
Upgrade firmware.
Export the configuration file.
Import the configuration file.
Change password.
Restart device.
Restart port.
Device IP address.
IP address list containing 1 IP address per line.
Device list.
File to be imported or upgraded.
The Device list with new password settings.
Device's user account for login.
Device's password for login.
The new password for the specific user.
Secret key for import/export configuration.
Specific serial ports to be restarted.
Output file name.
Moxa CLI Configuration Tool Getting Started
2-3
Command Function
Export result log file.
Keep network settings for configuration import.
Don't reboot device after finishing executing command.
Print process message for upgrade firmware command
Timeout(sec).
Device List
As mentioned in a previous section, MCC_Tool supports management tasks to a device or a range of
devices. Managing multiple devices via MCC_Tool requires device list(s). MCC_Tool includes an example file
of a device list, named DeviceList under Linux and DeviceList.txt under Windows. The format of the device
list is:
Model
ServerName
IP
MAC
FwVer
User
PWD
CfgFile
Key
FwFile
Port
NPort6650;
NPort6650_123;
192.168.1.1;
00:90:e8:01:02:03;
1.3;
;
moxa;
;
moxa;
;
;
NOTE
1.
To import configuration, please identify the CfgFile and Key column.
2.
To export configuration, please input the pre-shared key under Key column (This function only works on
NPort products).
3.
To upgrade firmware, please input the firmware name under FwFile column.
4.
To restart a specific port, please input the specific port under Port column (This function only works on
the NPort device server products).
Support Product Series
Because of easy maintenance, MCC Tool separates the device support list by independent product line
plugin, which includes the E1200_model, I4500_model, MGate model, and NPort_model since version 1.1.
In the future, you may update the plugin to support new product models.
Function Support Table
Due to firmware differences, some functions are not available for certain models; user may refer to the
table below for function support coverage.
NPort 6000
Series
NPort IA5000A/5000A
Series
MGate 3000
Series
ioLogik E1200
Series
ioThinx 4500
Series
Report firmware
versions
Upgrade
firmware
• Does not support account management (
-u
)
Export device’s
configuration
• Does not support account management (
-u
)
• Does not support file decryption (
-dk
)
Import device’s
configuration
• Does not support
account management
(-u)
• Does not support file
decryption (
-dk
)
• Does not support account management (
-u
)
• Does not support file decryption (-dk)
• Does not allow device to reject to restart (-nr)
Restart specific
serial port(s)
• Does not support
account management
(
-u
)
• Does not support this command
Moxa CLI Configuration Tool Getting Started
2-4
Restart the
devices
• Does not support account management (
-u
)
•
Set password
• Does not support
account management
(-u)
• Does not support account
management (-u)
• Does not allow device to reject to
restart (
-nr
)
•
Usage Examples of Supported Functions
Report Firmware Versions
Report firmware version of an individual device or a range of devices specified through an IP address list.
Output is directed to the screen, unless an output file is specified.
MCC_Tool –fw –r –i [ip_address] –o [output_file]
MCC_Tool –fw –r –il [IP_address_list] –o [output_file]
MCC_Tool –fw –r –il [IP_address_list] –o [output_file] –t [timeout_value]
Example of the IP address list file of Moxa devices:
192.168.1.1;
192.168.1.2;
192.168.1.3;
Parameters Description:
Command Function
-fw
Execute actions for firmware related
-r
Report firmware version
-i
Device’s IP address (192.168.1.1)
-il
IP address list containing 1 IP address per line
-o
Output file name (can generate the Device List file)
-l
Export result log file
-t
Timeout (1~120 seconds)
Default value: 10 seconds
Example: Obtain firmware version of devices at IP.list and output to DeviceList file
MCC_Tool –fw –r –il IP.list –o DeviceList
The result log should include the items below:
Model
ServerName
IP
MAC
FwVer
User
PWD
CfgFile
Key
FwFile
Port
NPort6650;
NPort6650_123;
192.168.1.1;
00:90:e8:01:02:03;
1.3;
;
moxa;
;
moxa;
;
;
NPort6150;
NPort6150_456;
192.168.1.2;
00:90:e8:04:05:06;
1.3;
;
moxa;
;
moxa;
;
;
NOTE
You may use this command to generate the
Device List for other function usage. The output value under
the
PWD
and Key columns are dummy values, where user will need to input the password and key information
of the device when executing other function commands with the device list. Other columns h
ighlighted will
need to be assigned value
s when executing specific commands,
such as import configuration file or firmware
upgrade.
Moxa CLI Configuration Tool Getting Started
2-5
Upgrade Firmware and Restart the Device
The password(s) must be specified by a command parameter or by the DeviceList file before upgrading
the firmware and restarting a specific device (or multiple devices at the same time). After upgrading
firmware, users should use search the command to check whether the device reboots successfully or not.
MCC_Tool –fw –up –i [ip_address] –u [user] –p [password] –f [firmware_file] –l
[result_log]
MCC_Tool –fw –up –d [device_list] –l [result_log]
MCC_Tool –fw –up –d [device_list] –l [result_log] –t [timeout_value]
Parameters Description:
Command Function Remark
-fw
Execute actions for firmware related
-up
Upgrade firmware version
-i
Device’s IP address (192.168.1.1)
-u
Device’s user account for login.
*This option may only work with the
models that have user account
management.
Only the NPort 6000
Series supports this
command function.
-p
Device’s password for login
-d
Device list
-f
Firmware file to be upgraded
-l
Export result log file
-t
Timeout (1~1200 seconds)
Default value: 800 seconds
-print
Print upgrade process status message
Example: Upgrade firmware using a device list and capture the results in an import log
MCC_Tool –fw –u –d DeviceList –l result_log
The result_log should include the items below:
Model
ServerName
IP
MAC
FwFile
ErrCode
NPort6650;
NPort6650_123;
192.168.1.1;
00:90:e8:01:02:03;
NP6000_V1.3.rom;
0;
NPort6150;
NPort6150_456;
192.168.1.2;
00:90:e8:04:05:06;
NP6000_V1.3.rom;
0;
Export/Import Device’s Configuration
Export/Import the device configuration for a specific device or a range of devices through the device list file.
The password must be specified by parameter or by the device list file. Device configurations are stored in
individual files, using device type, IP address, and file create date as the filename. The result log is directly
printed on the screen, or the user can specify a result_log file for it.
MCC_Tool –cfg –ex –i [ip_address] –u [user] –p [password] –dk [key] –l
[result_log]
MCC_Tool –cfg –ex –d [device_list] –l [result_log]
MCC_Tool –cfg –ex –d [device_list] –l [result_log] –t [timeout_value]
MCC_Tool –cfg –im –i [ip_address] –u [user] –p [password] –dk [key] –f [cfg_file]
–l [result_log] –n –nr
MCC_Tool –cfg –im –d [device_list] –l [result_log] –n –nr
MCC_Tool –cfg –im –d [device_list] –l [result_log] –t [timeout_value]
Parameters Description:
Command Function Remark
-cfg
Execute actions for configuration related
Moxa CLI Configuration Tool Getting Started
2-6
-ex
Export the configuration file
-im
Import the configuration file
-i
Device IP address (192.168.1.1)
-d
Device list
-u
Device’s user account for login
*This option may only work with the models
that have user account management.
Only the NPort 6000
Series supports this
command function.
-p
Device’s password for login
-dk
When Exporting configuration:
The command decrypts the exported file with
the pre-shared key.
• If this parameter is not used, the
exported file will be encrypted by the
pre-shared key set on the firmware of the
device.
• If this parameter is used, the exported
file will be decrypted to a clear-
txt file
for editing.
When Importing configuration:
If the configuration file that needs to be
imported is encrypted, the command is needed
with pre-shared key.
• If the import configuration file is
without -n, mcc tool will ignore -dk
(won't return -11).
• If the import configuration file is with -
n, mcc tool will use pre-shared key to
decrypt the encrypted file. Therefore, if
the key is wrong for decrypting the file,
mcc tool will return -10. However, if the
file is in plain text, and user inputs
pre-shared key, it will ignore the key
(won't return -10).*
(by parameter -dk or the key column in the device list file)
*This option may only work with the models
that support encrypted configuration files.
Only the NPort 6000
Series supports this
command function.
-f
The configuration file to be imported
Only for import
configuration function
-n
Keep original network parameters (includes
IP, subnet mask, gateway, and DNS)
Only for import
configuration function
-nr
Do not reboot the device after importing the
configuration file
Only for import
configuration function.
MGate, ioLogik, and
ioThinx devices do not
support this command.
-l
Export result log file
-t
Timeout (1~120 seconds)
Export function Default value: 30 seconds
Import function Default value: 60 seconds
Example: Export the configuration using a device list and export the results to a result log
MCC_Tool –cfg –ex –d DeviceList –l result_log
The result_log should include the following items:
Moxa CLI Configuration Tool Getting Started
2-7
Model
ServerName
IP
MAC
FwVer
ExportCfgFile
Key
ErrCode
NPort6650;
NPort6650_123;
192.168.1.1;
00:90:e8:01:02:03;
1.3;
NP6650_192_168_1_1_20170622.ini;
moxa;
0;
NPort6150;
NPort6150_456;
192.168.1.2;
00:90:e8:04:05:06;
1.3;
NP6650_192_168_1_2_20170622.ini;
moxa;
0;
Example: Import the configuration to a device list (with restart the units) and export the results to a result
log
MCC_Tool –cfg –im –d DeviceList –l result_log
The result_log should include the items below:
Model
ServerName
IP
MAC
FwVer
CfgFile
Key
ErrCode
NPort6650;
NPort6650_123;
192.168.1.1;
00:90:e8:01:02:03;
1.3;
NP6650_192_168_1_1_20170622.ini
moxa;
0;
NPort6150;
NPort6150_456;
192.168.1.2;
00:90:e8:04:05:06;
1.3;
NP6650_192_168_1_2_20170622.ini
moxa;
0;
Example: Import the configuration to a device list without restarting the units and export the results to a
result log
MCC_Tool –cfg –im –d DeviceList –nr –l result_log
Restart Specific Serial Ports or the Whole Devices
Restart the specific port(s) or the device itself for an individual device or a range of devices specified by the
device list file. The password must be specified by a parameter or by the device list file. Device
configurations are stored in individual files, using device type, IP address, and file create date as the
filename. The result log is directly printed on the screen, or users can specify a result_log file for it.
MCC_Tool –re –sp –ps [1-4,7] –I [ip_address] –u [user] –p [password]–l
[result_log]
MCC_Tool –re –sp –d [device_list] –l [result_log]
MCC_Tool –re –sp –d [device_list] –l [result_log] –t [timeout_value]
MCC_Tool –re –de –I [ip_address] –u [user] –p [password] –l [result_log]
MCC_Tool –re –de –d [device_list] –l [result_log]
MCC_Tool –re –de –d [device_list] –l [result_log] –t [timeout_value]
Parameters Description:
Command Function Remark
-re
Execute actions related to restart.
-sp
Restart specific serial ports of the
device. This option may only work with
the models that support restart ports
MGate and ioLogik devices
do not support restart
specific port functions.
-de
Restart Device
-ps
Used for restarting specific ports that
assign which serial ports should be
restarted
MGate and ioLogik devices
do not support restart
specific port functions.
-i
Device IP address (192.168.1.1)
-u
Device’s user account for login
*This option may only work with the
models that have user account
management
Only the NPort 6000
Series supports this
command function.
-p
Device’s password for login
-d
Device list
-l
Export result log file
-t
Timeout (1~120 seconds)
Restart device, the default value is 15
seconds
Restart port, the default value is 10
seconds
Moxa CLI Configuration Tool Getting Started
2-8
Example: Restart port using a device list and export the results to a result log
MCC_Tool –re –sp –d DeviceList –l result_log
The result_log should include items below:
Model
ServerName
IP
MAC
FwVer
Port
ErrCode
NPort6650;
NPort6650_123;
192.168.1.1;
00:90:e8:01:02:03;
1.3;
2-5, 8, 10;
0;
NPort6150;
NPort6150_456;
192.168.1.2;
00:90:e8:04:05:06;
1.3;
1,2,3;
0;
The serial ports 2-5, 8 and 10 of device 1 (NPort 6650) have been restarted.
Example: Restart device using a device list and export the results to a result log
MCC_Tool –re –de –d DeviceList –l result_log
The result_log should include the following items:
Model
ServerName
IP
MAC
FwVer
ErrCode
NPort6650;
NPort6650_123;
192.168.1.1;
00:90:e8:01:02:03;
1.3;
0;
NPort6150;
NPort6150_456;
192.168.1.2;
00:90:e8:04:05:06;
1.3;
0;
Change User’s Password on the Device
Set the password of the target device specified by an IP address. The current password must be specified by
a parameter or by the Device List file.
MCC_Tool –pw –ch –i [ip_address] –u [user] –p [old_password] –npw [new_password]
MCC_Tool –pw –ch –d [device_list] –nd [device_list_new_password] –l [result_log]
MCC_Tool –pw –ch –d [device_list] –nd [device_list_new_password] –l [result_log]
–t [timeout_value]
Parameters’ Description:
Command Function Remark
-pw
Execute actions for password related
-ch
Change password
-npw
The new password for the specific user
-i
Device’s IP address (192.168.1.1)
-u
Device’s user account for login
*This option may only work with the
models that have user account management
Only the NPort 6000
Series supports this
command function.
-p
Device’s password for login (old
password)
-d
Device list
-nd
The Device list with new password
settings
The user will need to
assign a new password in
the Device List when
using -nd command.
-l
Export result log file
-nr
Don’t reboot device after changing
password.
MGate and ioLogik devices
do not support this
command.
-t
Timeout (1~120 seconds)
Default value: 60 seconds
Example: Set new password as “5678” then restart the device to make it effective, and print the result on
the screen
MCC_Tool –pw 5678 –i 192.168.1.1 –u admin –p moxa
Moxa CLI Configuration Tool Getting Started
2-9
Example: Set new password from a device list and then restart the device to make it effective, and export
the results to a result log
MCC_Tool –pw DeviceList_New –d DeviceList –l result_log
The result_log should include the items below:
Model
ServerName
IP
MAC
FwVer
User
PWD
ErrCode
NPort6650;
NPort6650_123;
192.168.1.1;
00:90:e8:01:02:03;
1.3;
admin;
5678;
0;
NPort6150;
NPort6150_456;
192.168.1.2;
00:90:e8:04:05:06;
1.3;
admin;
moxa;
0;
Show Support Model List
Show the supported models of the MCC Tool.
MCC_Tool -ml
Update Plugin
Users may update the Plugin for the MCC Tool to support new models, which may not be included in the
current version. The command is as follow below. This function is supported by MCC_Tool version 1.1 and
later.
MCC_Tool -install "path of the plugin"
Error Code Explanation
The MCC_Tool has the same error code for all the command options, please refer to below sheet for all the
details:
Return Value Description
0 Successful
-1 Device not found
-2 Password or username does not match
-3 Exceeds the length of the password
-4 Failed to open the file
If the target file path exists, please make sure you have the privilege to the
target path
-5 The action timed out
-6 Import failed
-7 Firmware upgrade failed
-8 Exceeds the length of the new password
-9 Fail to set restart port index
-10 Cipher key for decrypting the configuration file is mismatched
-11 Invalid parameter
E.g.,
1. Input parameters are not described above
2. The parameters do not work for some devices (e.g., -u for the MGate MB3000
Series, which does not support user account function, or -dk for the NPort 5000A
Series, which does not support pre-shared key function)
3. Using device list file should not input -i, -u, -p, or -npw
-12 Unsupported command
E.g., execute restart specific port command (MCC_Tool -re -sp) for the MGate
MB3000 Series will get error code -12
-13 A lack of information in the device list
If a specific NPort only exists in the device_list_new_password but not in the
device_list (original device list with old password), then an error will occur.
Moxa CLI Configuration Tool Getting Started
2-10
-14 A lack of information in the new password list
If there is no new password in the device_list_new_password but the device
exists in the original device list, then an error will occur.
-15 Not executable due to an error of other devices in the list
-16 The MCC_Tool does not support the firmware version of the device. Please
upgrade the device to the supported firmware version (reference to the "Support
Models" section)
Other value Contact Moxa
/