HP DesignJet 10000s Printer series Owner's manual

1

Index Page

1. English (GB) HP Designjet 8000s / 9000s/10000s Air Purifier System 3

2. German (D) HP Designjet 8000s / 9000s/10000s Luft-Reinigungssystem 29

3. Spanish (E) Sistema de purificación de aire 55

HP Designjet 8000s / 9000s/10000s

4. Portuguese (P) Sistema de Purificação de Ar 81

HP Designjet 8000s / 9000s/10000s

5. French (F) HP Designjet 8000s / 9000s/10000s 107

Système de nettoyage d'air

6. Italian (I) Sistema di depurazione dell'aria 133

HP Designjet 8000s / 9000s/10000s

7. Turkish (TR)

HP Designjet 8000s / 9000s/10000s 159

Hava Temizleme Sistemi

8. Polish (PL) System oczyszczania powietrza 185

HP Designjet 8000s / 9000s/10000s

9. Hungarian (H) HP Designjet 8000s / 9000s/10000s Légtisztító rendszer 211

10. Greek (GR)

Óýóôçìá ÊÊáèáñéóìïý ÁÁÝñá

237

HP DDesignjet 88000s // 99000s/10000s

11. Czech (CZ) Cistic vzduchu HP Designjet 8000s / 9000s/10000s 263

12. Russian (RUS) HP Designjet 8000s / 9000s/10000s 289

Система очистки воздуха

13. Korean (ROK)HP Designjet 8000s / 9000s/10000s 315

14. Chinese (VRC) HP Designjet 8000s / 9000s/10000s 341

15. Taiwanese(RC) HP Designjet 8000s / 9000s/10000s 367

Page is loading ...

4 User´s Guide

I Introduction

This User's Guide is an essential help for the successful and safe operation of the HP Designjet

9000s/10000s Air Purifier System and HP Designjet 8000s Air Purifier System - referred to in

this document as APS.

The operating instructions contain important information for operating the APS safely, properly

and economically. Following these instructions can help to avoid dangerous situations, repair

costs and reduce downtimes and improve the reliability and extend the useful life of the APS.

The operating instructions must at all times be kept available near the APS.

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not

limited to, the implied warranties of merchantability and fitness for a particular

purpose.

Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequenti-

al damages in connection with the furnishing, performance, or use of this material. No part of

this document may be photocopied or translated to another language without the prior written

consent of Hewlett-Packard Company.

5HP Air Purifier System

II Product ddescription

HP DDesignjet 88000s AAir PPurifier SSystem

HP DDesignjet 99000s/10000s AAir PPurifier SSystem

1

Transparent display, membrane

keyboard

2 Casing cover

3 Filter casing 4 Service flap on the filter housing

5 Fan housing 6 Fan & electronics cover

7 Sound absorption module 8 Castor with brake

9 Castor 10 Intake stub

11

HP Designjet APS 8000s /

9000s/10000s Filter

12 Filter lifting mechanism

13 Exhaust grid

6 User´s Guide

III Safety

III 11 General iinformation

The APS is built in accordance with state of the art technology and adherence to safety rules.

Nevertheless, during use there may be dangers to the user or a third parties if it is not used for

the purpose for which it was intended, and not properly maintained.

III 22 Use aas iintended

The APS may only be operated with the HP printers for which it is designed.

The work area where the HP Designjet 8000s or 9000s/10000s printer is used must be ade-

quately ventilated. The APS is not a substitute for ventilation of the work area.

The APS is not intended to be used as a substitute for adequate ventilation of the work area.

The APS removes

v

olatile

o

rganic

c

ompounds (VOC's ) released inside the printer during ope-

ration, but prints that are drying and being stored also release VOC's. The APS only reduces

the release of volatile organic compounds in the work area from the printer and it is not inten-

ded under any circumstances to be used in closed room without ventilation.

Any other use other than direct connection to an HP Designjet 8000s and 9000s/10000s prin-

ter is not considered to be proper use of the APS.

This also applies for unauthorized modifications to the APS. In particular in the case of replace-

ment filter elements purchased from third parties, there is no guarantee that performance will

meet HP specifications.

Proper use includes compliance with the information:

- on safety,

- on operation and

- on maintenance,

as described in this user's guide

III 33 Information oon ssigns aand ssymbols

The following designations or symbols for safety information and particularly important details

are used in these operating instructions:

Warning!

Failure to follow the guidelines marked with this symbol could result in serious perso

nal injury or death

Caution!

Failure to follow the guidelines marked with this symbol could result in minor personal

injury or damage to the product.

Note

Additional information for a safe, proper and efficient handling of the APS.

• Work and/or operating steps are marked with the large reference point. The

steps are to be executed in the order from top to bottom!

– Lists are marked with the dash.

All information should be complied with, for the proper use of the APS. Please be sure all ope-

rators of the APS are completely familiar with information in this manual.

Information and symbols directly attached to the APS, such as warning signs, warning stickers

component part markings etc must be observed.

The information and symbols directly attached to the APS may not be removed and must be kept

in a completely readable condition.

III 44 Warnings

– Do not immerse the APS in water or other liquids.

– Do not use the APS in areas with very high concentration of dust.

– Do not use the APS outdoors.

– Use only the proper power cables supplied by HP with the APS.

– Use the power supply voltage specified on the nameplate. Doing otherwise may cause

fire or electric shock.

– Do not connect multiple loads to one power outlet. Doing so may cause fire or electric

shock.

– Do not disassemble or remodel the APS. Do not repair the APS by yourself. Doing so

may cause fire, electric shock, or other accidents.

– Do not remove the screwed covers, because they content high-voltage. Careless remo

val might result in electric shock or burn.

– See the label on the fan & electronics cover (Number 6 in APS description).

– Do not disconnect or connect the power cable with wet hands. Doing so may lead to

electric shock.

– Turn the APS OFF and unplug he power cable from the power outlet if there is smoke

or an unusual smell coming from the APS.

– Do not install or operate the APS within 8 meters (25 feet) of open flames, sparks, or

other sources of ignition.

– Always use genuine HP replacement Filter Elements. These have been designed for reli

able filtration and qualified to work with your Designjet 8000s or 9000s/10000s prin-

ter. Using non-HP Filter Elements may result in ineffective filtration of volatile organic

compounds and pose health and safety hazards.

– Be sure all operators are trained in the use of emergency equipment such as eye wash

stations and fire extinguishers and know where they are located.

– Used filters capture an organic solvent (ethylene glycol monobutyl ether acetate,

CAS No. 112-07-2) and other chemicals from ink vapors. When disposing used filter

cartridges it is your responsibility to observe all local, state, and federal regulations rela

ted to the handling, use, storage, and disposal of organic solvents.

– Do not disassemble the filter elements.

– If any liquid is present on used filter elements, avoid contact with skin, eyes, and

clothing. Handle the used filters while wearing latex or Nitrile ® gloves. Immediately

wash skin that has come in contact with liquids with soapy water. Remove any clothing

soaked with liquids from contact with skin. If liquid comes in contact with eyes, use an

approved eye wash station and consult a doctor if necessary. If an approved eye wash

station is not available, flush eyes with cold water and contact a doctor if necessary.

– The liquid captured by the filters is combustible. Do not use or store used filters within 8

meters (25 feet) of open flames, sparks, or other sources of ignition.

– Do not smoke within 8 meters (25 feet) of the APS.

– Keep used filter cartridges out of the reach of children.

– Do not obstruct air inlets and outlet.

7HP Air Purifier System

8 User´s Guide

III 55 Warnings ffor mmaintenance

The APS must be switched off for maintenance, and be secured against being switched on again

unexpectedly, by:

• the APS must be switched off at the ON/OFF switch and then

• the power plug must be removed from the wall power socket.

Do not put your hand in the cover grid of the fan during fitting, assembly or service work.

– After switching off /shutdown of the APS wait until the fan stops.

To avoid electric shocks do not open any electrical parts and casing and covers.

It is recommended to use protective gloves (disposable gloves made of polyethylene, latex or

Nitrile®) before carrying out the filters replacement and/or the suction hoses.

Replace filter elements at the stated intervals. Always tightly rescrew screw connections

loosened.

Do not use any aggressive agents or cleaning agents which contain solvents. Use lint-free

cleaning cloths.

Only use mild water-based cleaning agents. Do not use any organic solvents, as there is a risk

of fire and explosion!

Ensure ssafe aand eenvironmentally-ffriendly ddisposal oof mmaterials aand ssupplies.

III 66 Protective eequipment

The APS is equipped with safety interlocks to protect the user and is constructed and produced

in accordance with state-of-the-art- technology to meet operational safety regulations. In order

to ensure safe and environmentally-responsible operation, the following safety features have

been installed:

– The fan is secured by a protective plate or grid, which may only be removed using tools.

– All elements of the control systems will move into a safe status for operators, APS and

the environment in the case of power cut or reported disturbances. An unexpected

restart is not possible after this.

– All electrical parts carry the CE mark for low voltage and/or EMV.

– A potential compensation (Ø > 1.5 mm²) of all conducting components is installed to

ground the APS.

– The APS is designed according to protective type IP 20.

9HP Air Purifier System

Index

I Introduction 4

II Product ddescription 5

III Safety 6

III 1 General information 6

III 2 Use as intended 6

III 3 Information on signs and symbols 6

III 4 Warnings 7

III 5 Warnings for maintenance 8

III 6 Protective equipment 8

1 Installation && FFunction DDescription 10

1.1 Transport on wooden pallet 10

1.2 Unpacking and installation 11

1.3 Box content 11

1.4 Connection of the printer 12

1.5 Power on the APS 12

1.6 Function description 12

2 Operation 13

2.1 Operating conditions 13

2.2 Operation 13

2.3 Test operation 14

3 Maintenance 15

3.1 General information 15

3.2 Routine maintenance work 15

3.3 Replacement of filters 15

3.3.1 Removal of the old filter(s) 16

3.3.2 Insert the new filter(s) 17

3.4 Enter the code of the new replacement filter 18

3.4.1 HP Designjet 8000s Air Purifier System 18

3.4.2 HP Designjet 9000s/10000s Air Purifier System 19

4 Disposal 20

5 Troubleshooting 21

6 Legal iinformation 22

7 Regulatory nnotices 25

7.1 Regulatory model number 25

7.2 Regulatory statements 25

8 Declaration oof cconformity 27

9 Technical ddata 28

10 User´s Guide

1 Installation && FFunction DDescription

1.1 Warnings ffor mmaintenance

The APS is delivered upright on a wooden pallet according to the IPPC standard. The following

industrial trucks are permitted for transporting the wooden pallets:

– Fork lift trucks and

– Fork stacker lift trucks.

Do not drop the APS during handling.

Secure the wooden pallets with the upright APS during transport to prevent the APS from falling

over.

Observe the applicable accident prevention and labour safety regulations.

You must observe the information on the packaging.

The APS or the wooden pallet with the APS is to be secured on the transport vehicle against slip-

ping and falling over.

Warning!

If the wooden pallets are not secured properly the APS may fall down and cause seri-

ous injury or death.

Only use suitable hoisting equipment and securing means!

The driver must be authorized to steer the industrial truck.

Drive between the spans of the wooden pallet using the fork lift truck.

Observe the following information for transporting the APS:

– The fork lift truck must be permitted for the total weight of the wooden pallets with

upright APS.

– Weight of the complete HP Designjet 8000s APS, net: approx. 60 kg

– Weight of the wooden pallet + 8000s APS + packaging: approx. 76 kg

– Weight of the complete HP Designjet 9000s/10000s APS, net: approx. 95 kg

– Weight of the wooden pallet + 9000s/10000s APS + packaging:approx. 113 kg

– The length of the forks must be at least: 1,000 mm

– The transport crates must be tightly fixed to the industrial truck in order to avoid

them falling over.

It is to be prevented that the APS and the hoisting platform of the industrial truck come into

contact:

– For this purpose wedge a distance wood or cardboard between the packaging of

the APS and the platform.

– Avoid hard knocks when setting down the APS.

– All persons must leave the working area of the industrial truck before lifting the APS.

11HP Air Purifier System

1.2 Unpacking aand iinstallation

Note:

When the APS is installed, allow adequate space for exhaust hoses from the printer. Lo-

cate these hoses and the APS so that they do not pose a trip hazard or interfere with the opera-

tion of the printer such as loading and unloading media, replacing Ink Cartridges, inspecting

and replacing the Waste Ink Bottle.

Note:

Allow adequate space around the APS to remove and replace the filter elements.

Note:

Do not install the APS in an area where it receives direct airflow from air conditioners,

heaters, or ventilators.

Note:

Proceed as follows when unpacking and installing the APS:

– Do not lift the APS off the wooden pallet or remove from the transport packaging

until you reach the place of installation. Carefully remove the packaging.

– Check the completeness of the delivery based on the packing list. Also check the

complete delivery for external damages, such as may have occurred in transit.

– Move the APS on its casters until you reach the place of installation

– Install the APS on a level, firm surface.

– Secure the APS against unintended rolling by pressing the brakes on the casters.

– The APS must be placed in such a way that the exhaust grid can lead the filtered

air back into the working room.

– Secure the APS with placing of the adjustment feet to prevent the APS for uninten-

tional tilting (according EN 60950-1 test of stableness) to the side. In the bottom of

the APS housing, 4 nuts are fastened for placing of the adjustment feet. To be able

to screw the adjustment feet into the 4

nuts it is necessary to remove the 4 exi-

sting screws M10.

The positioning of the adjustment feet has

to be according to the underground in

such a way that the APS is placed on an

even and firm underground and the exi-

sting wheels are not relieved.

1.3 Box ccontent

When you receive the APS please check in detail the box content. The regular scope of delivery

includes:

– APS, complete (with built-in filter ele-

ments);

– Hose set I (4 m hose, 2 m hose; respec-

tively incl. connection stubs and clamping

hoses)

–Power cord

You can receive more than one, please

choose the proper for your need

– 4 adjustment feet M10, length: 85 mm

– 1 open-end wrench

12 User´s Guide

1.4 Connection oof tthe pprinter

The APS is installed to the printer connecting two hoses as

follows:

– Take the hoses and plug the end stubs on the

intake ports of the APS

Note:

The two hoses are fitted with a stub at one end.

– The other end of the hose is pushed through the

exhaust attachment flange of the printer and

mounted with a clamping hose.

Note:

The printer has on the left and right side respectively two

exhaust attachment flanges.

1.5 Power oon tthe AAPS

Connect the APS as follows:

– Insert the plug of the power cable into the socket.

Ensure that the supply voltage matches that posted on the unit.

– Finally check again all connection for accuracy and tight fit.

The APS may be put into operation after all hose pipes have been connected and the connec-

tion checked.

1.6 Function ddescription

Suction hoses are connected directly between exhaust ports on the HP Designjet 8000s or

9000s/10000s printers and the APS.

The APS is switched on at its membrane keyboard.

Air containing volatile organic compounds from HP low-solvent inks released inside the HP Des-

ignjet 8000s or 9000s/10000s printers is removed through the hoses and brought into the fil-

ter casing and filter elements.

The filter element consists of the following filter levels:

– Pre-filter mat and activated carbon filter.

Purified air with volatile organic compounds trapped in the filter elements is drawn out by the

fan below the filter element and then passes through the exhaust grid in the sound absorption

module attached at the rear.

13HP Air Purifier System

2 Operation

2.1 Operating cconditions

The APS must be operated in a vibration-free, dry and as far as possible dust-free location.

The APS must be operated in a work area receiving adequate ventilation.

Under no circumstance operate the APS in a closed room without ventilation.

The air temperature must be in a temperature range between + 5 °C and + 35 °C.

The relative humidity in the air may not exceed 70 %. Condensation from humidity on the sur-

faces of the APS must be avoided.

2.2 Operation

The APS is controlled via its membrane control panel with transparent display ( Fig. 1). All the

functions of the APS will be controlled from this panel.

The basic setting will be displayed in the transparent display when the machine is switched on:

– On the left the total hours of operation on the installed filter element.

– In the middle the actual filter saturation given as a percentage of full capacity.

– On the right: fan speed as a percentage of the maximum. The minimum value is

set to 20%.

You will find the following control elements on the membrane control panel of the APS:

ON/OFF button

The ON/OFF button is used for switching the APS on and off. When switched on

you can hear the fan start and the air will be extracted from the printer.

If you change the values (e. g. fan speed), then these settings will be saved when

the unit is switched off. When it is switched on again the APS will continue to ope-

rate with these settings.

ENTER bbutton

This button is only to be used by your service technician for control work and adjust-

ments to the electronic control of the APS (e.g. after replacement of the filter ele-

ments).

If nothing is entered/changed for several seconds, the display automatically returns

to the basic setting.

Figure1: membrane control panel with transparent display

Button ““+”

This button is used for increasing the fan speed in %-steps. You can notice the

increase in the number of revolutions by the increase in the level of noise. The

changed value will be taken over directly.

Button ““–”

This button is used for reducing fan speed in %-steps. You can notice the reduction

in speed by the reduction in the level of noise. The changed value will be taken

over directly.

LED ““Error” ((red)

If the red LED lights up the filter element is saturated and must be replaced.

LED ““Run” ((green)

Shows that the APS is switched on. If the LED Run blinks green, it means the filter

element must be replaced within 100 additional operating hours.

2.3 Test ooperation

Note

Carry out the test operation if you have just purchased the APS and would like to

become familiar with the functions.

Carry out the test of the APS as follows:

• First check all connections on the APS that they are correct and fitted tightly.

• Switch the APS on via the membrane keyboard using the button ON/OFF.

• Increase the fan speed, by touching the button "+" and keeping it pressed

down. You can notice the increase in the fan speed by the increase in the

level of noise. At the same time, the right % appears in the transparent

display.

• Reduce the fan speed, by touching the button "– " and keeping it pressed

down. You can notice the reduction in speed by the reduction in the level of

noise. In addition to this, the right %-appears in the transparent display

(Minimum 20 %).

• Switch the APS off via the membrane keyboard using the button ON/OFF. If

the APS operates correctly, then the APS is ready for normal operation.

14 User´s Guide

15HP Air Purifier System

3 Maintenance

3.1 General iinformation

Warning!

Used filters capture an organic solvent (ethylene glycol monobutyl ether acetate, CAS

No. 112-07-2) and other chemicals from ink vapors. When disposing used filter car--

tridges it is your responsibility to observe all local, state, and federal regulations rela-

ted to the handling, use, storage, and disposal of organic solvents.

Warning!

You must remove the power supply cable on the APS during cleaning and service work.

Note:

Please also follow the safety instructions in section III Safety.

3.2 Routine mmaintenance wwork

You must inspect the accessible areas of the APS daily for damage and assess the APS for pro-

per operation

Caution!

– Labels and control elements or warning signs may become illegible through un--

avoidable dirt deposits. This can lead to faulty operation, which may cause a safety

hazard.

– It is recommended to clean control elements, displays and warning stickers once a

week removing accumulated dust and other dirt by wiping with a clean, damp

cloth. Avoid using an excessively wet cloth that may release liquids into the APS.

– Avoid the use of solvent cleaners, which may attack elements of the keypad, dis

play, gaskets, or paint. Only water-based cleaners or soapy water are recommen

ded.

– Do not allow liquids to spill into or penetrate into the APS.

3.3 Replacement oof ffilters

The filter elements must be replaced after an interval period of 800 operating hours. The dis-

play of the filter contamination in the transparent display shows in this case 100 % and the red

LED (Error) will light permanently. All activated carbon filters will become full at different speeds

depending on type of use, and they should be replaced between 700 and 800 operating

hours, and no later than 800 hours under any circumstance. For ordering new filters:

Designation

Product NNumber

HP Designjet 8000s / 9000s/10000s APS Filter

(HP Designjet 8000s Air Purifier system,

1x filter element required)

(HP Designjet 9000s/10000s Air Purifier system,

2x filter elements required )

Q6679 A

16 User´s Guide

Note

The green LED blinks after an interval period of 700 operating hours as an indication

to order new filters, and also this means the filter elements must be replaced within

100 additional operating hours.

Caution!

When removing or inserting the filter elements it is recommended to use protective glo-

ves (disposable gloves made of polyethylene, latex or Nitrile®) before carrying out the

filters replacement and/or the suction hoses.

With the system "HP Designjet 8000s Air Purifier System" one filter element is used in the filter

unit. With the system "HP Designjet 9000s/10000s Air Purifier System" two filter elements are

placed behind each other in the filter unit. With the filter system "HP Designjet 9000s/10000s

Air Purification System" always replace both filter elements at the same time.

You should proceed as follows when replacing the filter:

3.3.1 Removal oof tthe oold ffilter(s)

• Switch off the APS at the membrane keyboard using the button.

• Secure the APS against being switched on again unexpectedly, by removing

the power cable from the wall power socket.

• Grasp the rear right of the service flap (Fig.1) with

one hand and open this to the left.

Note:

You must overcome the resistance of the latch!

• Remove the offset screwing key from the intake.

• Slacken the sealing lifting mechanism by turning the

adjusting screw (Fig. 2) using the offset screwing key.

Turn the adjusting screw until the filter element is at

the bottom and can be shifted freely.

• Release the filter locking (Fig. 3)

Figure 3

Figure 2

Figure 1

17HP Air Purifier System

• Grasp the handle of the filter element and pull the

filter element out of the filter housing (Fig. 4) while

it stands securely in the filter housing. You can secu-

rely grasp under filter element with both hands and

then place it down carefully.

Note

: Each filter element weights approx. 16 kg.

Immediately dispose of the used filter element. Used filters capture an organic solvent (ethylene

glycol monobutyl ether acetate, CAS No. 112-07-2) and other chemicals from ink vapors. When

disposing used filter cartridges it is your responsibility to observe all local, state, and federal

regulations related to the handling, use, storage, and disposal of organic solvents.

3.3.2 IInsert tthe nnew ffilter(s)

Please, proceed as follows:

• Remove the new filter element(s) from the packaging.

• Store the enclosed flyer with the code in a safe place.

You will need this later to reset the service interval.

• Push the filter element(s) (Fig. 5) into the filter housing

up to the stop. The surrounding gasket on the filter

element must be at the top, and the handle of the fil-

ter element must point towards the service opening.

• Put the filter locking. (Fig.6)

• Tighten the sealing lifting mechanism (Fig. 7) by tur-

ning the adjusting screw until it is completely tight.

• Insert the screwing key into the intake again.

• Close the service door until the latch engages.

Note:

Always pay attention that the surrounding gasket on the filter element(s) and on the pre-filter tray

at the top is pushed into the stop, and the adjusting screw is completely tight. Otherwise, this

can lead to leakages and the extracted gases and dust will not be filtered properly.

Figure 5

Figure 7

Figure 4

Figure 6

18 User´s Guide

3.4 Enter tthe ccode oof tthe nnew rreplacement ffilter

In order to reset the service interval one code must be entered with the HP Designjet 8000s Air

Purifier System. Two codes are necessary with the HP Designjet 9000s/10000s Air Purifier

System. The code input for the 8000s and 9000s/10000s is explained in the following chap-

ters.

3.4.1 HHP DDesignjet 88000s AAir PPurifier SSystem

After replacing the filter element the service interval must be reset using the code. The following

steps must be carried out in the following order:

Switch the APS on at the membrane keyboard using the button ON/OFF. When it

switches on you will hear the fan and it will begin to extract the gases.

If "service filter" is shown in the display you must press the button "+" or "– " to

suppress this fault report.

By pressing the button ENTER the programme name is displayed.

By pressing the button ENTER again "

code 1: 00000

" is displayed.

Now you can enter the code using these buttons. The code is on the flyer which is

enclosed with the new filter element.

By pressing the button ENTER the actual code is saved.

If this code has been entered correctly the value for the filter contamination (middle indication

in the display) is reset to "0%" and the blinking green (run) and red ( error ) LEDs will be reset.

Note

The code is on the flyer that is enclosed with the new filter element.

19HP Air Purifier System

3.4.2 HP DDesignjet 99000s/10000s AAir PPurifier SSystem

After replacing the filter element the service interval must be reset using the code. The following

steps must be carried out in the following order:

Switch the APS on at the membrane keyboard using the button ON/OFF. When it

switches on you will hear the fan and it will begin to extract the gases.

If "service filter" is shown in the display you must press the button "+" or "– " to

suppress this fault report.

By pressing the button ENTER the programme name is displayed.

By pressing the button ENTER again "

code 1: 00000

" is displayed.

Now you can enter the code using these buttons. The code is on the flyer which is

enclosed with the new filter element.

By pressing the ENTER the actual code is saved and "

code 2: 00000

" is

displayed.

Now you can enter the code using these buttons. The code is on the flyer which is

enclosed with the new filter element.

By pressing the ENTER the actual code is saved.

If this code has been entered correctly the value for the filter contamination (middle indication

in the display) is reset to "0%" and the LED`s which may be lit or blinking extinguishes.

Note

– With the HP Designjet 9000s/10000s Air Purifier System a "

code 2: 00000

" the code

from the second filter element also must be entered.

– If the code 2 was not entered correctly, then also the code 1 must be entered again.

20 User´s Guide

4 Disposal

It is the APS owner's responsibility to ensure that waste is disposed of in accordance with all lo-

cal, state and federal regulations.

There are registered waste management companies that have been authorized by local autho-

rities to manage waste collection and disposal and that will manage waste management and

disposal on your behalf.

We recommend that you contact your local authorities for a list of authorized companies, or you

can search for the nearest authorized waste disposal company on the World Wide Web.

Make sure that any waste disposal company you engage for this task is able to provide you with

the necessary documentation proving their authority to manage and dispose of waste legally.

You will be legally responsible for failing to dispose of waste according to local, state and fe-

deral legislation.

When you have established an authorized waste management company, they will need to know

the type of chemical that requires disposal and you will need to determine the type of agree-

ment that best meets your requirements.

They will need to know the common name or chemical CAS number of the main solvent found

in the printing supplies. Used filters capture an organic solvent (ethylene glycol monobutyl ether

acetate, CAS No. 112-07-2) and other chemicals from ink vapors that can be obtained on the

Material Safety Data Sheets (MSDS) available for all supplies at:

http://www.hp.com/hpinfo/globalcitizenship/environment/productdata/index.html

The APS captures organic solvents, and after removal and disposal of the filter elements, some

solvents may remain in the unit and hoses connected to the printer. If the APS is to be perma-

nently removed from operation, it is your responsibility to observe all local, state, and federal

relations related to the disposal of the components and materials of the APS.

21HP Air Purifier System

5 Troubleshooting

Fault Cause Correction

No suction

output

(fumes/gases

are not being

extracted).

Suction hose not connected

to the APS.

Connect suction hose to the APS.

Suction hose not connected

to the machine

Connect suction hose to the printer.

Damage to the suction

hose.

Replace suction hose.

Suction hose is connected

to the wrong machine.

Connect suction hose to the correct

machine.

Suction hose is connected

to the wrong point of entry

(opening) of the machine.

Connect suction hose to the right point of

entry (opening) of the machine.

Suction channel blocked. Check suction channel, if necessary cor-

rect error found.

Clean gas channel blo-

cked.

Check clean gas channel, if necessary

correct error found.

Suction output

too low

(fumes/gases

are hardly

being extracted).

Filter elements full. Replace filter package, dispose of old fil-

ter properly!

Damage to the suction

hose.

Replace suction hose.

Suction hose not correctly

connected to the APS.

Check fitting of the suction hose to the

APS, if applicable reinsert into suction

opening.

Suction hose not correctly

connected to the machine.

Check fitting of the suction hose to the

machine if necessary reconnect.

Air outlet blocked. Check air outlet status,and clean blocke

holes.

Suction hose is connected

to the wrong point of entry

(opening) on the machine.

Connect suction hose to the right point of

entry (opening) on the machine.

Fault on the APS. Contact your HP Service representative.

APS is not

running.

Plug connection power sup-

ply not or wrongly plugged

in.

Check/correctly plug in plug connection

power supply.

No power on the socket. Check power supply, if necessary correct

error.

Fault on the APS. Contact your HP Service representative.

22 User´s Guide

6 Legal iinformation

HP product Limited Warranty Period

HP Designjet 8000s/

9000s/10000s Air Purifier

System

1 year from the date of hardware's purchase by the

customer

HP Designjet 8000s /

9000s/10000s APS Filter

700 hours of operation or 9 months from the date of the

filter's purchase by the customer. Whatever comes first.

A. Extent of HP Limited Warranty

1. This Hewlett-Packard (HP) Limited Warranty gives you, the end-customer, express

limited warranty rights from HP. In addition, you may also have other legal rights under

the applicable local law or special written agreement with HP.

2. HP warrants to you that the HP products specified above will be free from defects in

materials and workmanship during the Limited Warranty Period specified above. The

Limited Warranty Period starts on the date of purchase. Your dated sales or delivery

receipt, showing the date of purchase of the product, is your proof of purchase date.

You may be required to provide proof of purchase as a condition of receiving warran-

ty service. You are entitled to warranty service according to the terms and conditions

of this document if a repair or replacement of your HP Products is required within the

Limited Warranty Period.

3. For software products, HP's Limited Warranty applies only to a failure to execute pro--

gramming instructions. HP does not warrant that the operation of any product will be

uninterrupted or error free.

4. HP's limited warranty covers only those defects which arise as a result of use of the HP

products as defined in the user's guide, and does not apply to any:

a. Improper, inadequate or lack of filter maintenance following the instructions de--

fined in the User's Guide in Chapter III Safety and 3 Maintenance.

b. Interfacing or parts not provided or supported by HP; or

c. Operation outside the product's specifications.

Routine printer maintenance operations in the HP Designjet 9000s/10000s / 8000s

Air Purifier System, such as cleaning and preventive maintenance services (including

parts contained in any preventive maintenance kit and HP service engineer visits), are

not covered by HP's Limited Warranty.

5. For the HP Designjet 9000s/10000s / 8000s Air Purifier System, the use of non-origi-

nal HP consumables (filter) do not affect either the HP's Limited Warranty to you or any

HP support contract with you. However, if printer failure or damage is attributable to

the use of a non-original HP consumable, HP will charge its standard time and mate-

rials charges to service the printer for the particular failure or damage.

Page is loading ...

HP DesignJet 10000s Printer series Owner's manual

This manual is also suitable for

HP DesignJet 10000s Printer series Owner's manual

in other languages

Related papers

Other documents