American Standard 1340.825.002 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
This manual is also suitable for
M968492 Rev.1.8 (8/19)
Certified to comply with ANSI A112.18.1M
1
2
PREPARE TUBE AND TEE ASSEMBLY
3
VALVE ASSEMBLY
2
3
1
1
2
9
8
Remove COUPLING NUT (1) and FERRULE (2) from each
VALVE (3) and slide onto TUBING (4).
Push TUBING (12) ends into VALVE (4) side outlets. Insert
VALVES (4) into mounting holes from underside of ledge.
Install LOCKNUTS (1), METAL WASHERS (3) and RUBBER
WASHERS (2) onto valve shanks.
Place RUBBER RING (8) into ESCUTCHEONS (7) and thread onto
valves until snug against internal stop.
Tighten LOCKNUT (1) to secure VALVE (4) position.
Slide FERRULE (10) and COUPLING NUT (11) to outlet of VALVE (4)
and tighten COUPLING NUT (11) firmly.
Place WASHER (14) on top of VALVE ASSEMBLY (4).
COLD
8"
4
10
11
6
5
11
10
12
4
4
14
14
MOUNTING
SURFACE
MOUNTING
SURFACE
LAVATORY
FAUCETS
Installation
Instructions
Thank you for selecting American-Standard...the
benchmark of fine quality for over 140 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Thread of VALVE BODY (4) should extend at least 5/16 inch above
MOUNTING SURFACE (9). If necessary, adjust LOCKNUT (1).
8
13
7
METERING
1340.825
1340.827
Plumbers' Putty or CaulkingAdjustable Wrench
2.5mm Hex Wrench
Channel Locks
Recommended tools
REMOVE REPLACE
Remove HANDLE (1) by
removing INDEX BUTTON (2)
and SET SCREW (3) with a
2.5mm hex wrench.
Pull off HANDLE (1).
Remove ACTUATOR
ASSEMBLY (4)
.
Replace WASHER (5) with
new Washer (5) that is
provided in separate bag.
Thread VALVE ACTUATORS (13) onto VALVES (4) and torque VALVE
ACTUATOR 12-15 ft. lbs, (12-20Nm).
REMOVE HANDLE AND
ACTUATOR ASSEMBLY
1
4
5
2
3
HOT
Connect water supply to VALVES (4) with 1/2" IPS FLEXIBLE
SUPPLIES or 3/8" O.D. BULL-NOSE RISERS. Use adjustable wrench
to tighten connections. Do not over tighten. Be careful not to kink
copper supply when bending. Use tubing cutter to cut to proper length.
1/2" IPS FLEXIBLE
SUPPLIES or 3/8" O.D.
BULL-NOSE RISERS
COUPLING NUT
Tubing Cutter
7
2
4
5/16''
MIN.
MOUNTING
SURFACE
8
9
1
3
Hook
M968492 Rev.1.8 (8/19)
Turn off hot and cold water
supplies before beginning.
CAUTION
4
Assemble RUBBER WASHER (5) and BRASS WASHER (6)
and LOCKNUT (7) onto SPOUT SHANK (4). Align SPOUT
ASSEMBLY. From underside of ledge, tighten LOCKNUT (7)
approximately halfway up the spout shank.
Press SPOUT SHANK (4) onto TEE (8) making certain that the
O-RING (3) is properly seated on SHANK (4). Push COUPLING (9)
into TEE (8) and attach to SPOUT SHANK (4) and tighten.
Por la parte inferior, apriete la tuerca (7) para asequrar el
cuerpo a la superficie de montaje.
SPOUT ASSEMBLY
Install RING WASHER (1) into SPOUT (2) recess. Check
that O-RING (3) on end of SPOUT SHANK (4) is in place.
Insert SPOUT SHANK (4) into center hole on mounting
surface.
SPOUT
RECESS
1
3
2
8
MOUNTING
SURFACE
SPOUT
ASSEMBLY
4
COLD
HOT
9
5
INSTALL HANDLES
Remove INDEX BUTTON (1; 2) and loosen SET SCREW (3) with a 2.5mm hex wrench.
Install HANDLES (4) onto VALVE STEM (5).
Tighten SET SCREWS (3) with 2.5mm Hex Wrench.
Replace INDEX BUTTONS. Red (1) in Left HANDLE (4) Blue (2) in Right HANDLE (4).
1
4
3
2.5mm
HEX WRENCH
3
5
4
2
5
6
7
M968492 Rev.1.8 (8/19)
TO ADJUST CYCLE TIME
7
8
1
2
3
4
TO INCREASE
CYCLE TIME
ROTAT E
CLOCKWISE
TO DECREASE
CYCLE TIME
ROTAT E
COUNTER-
CLOCKWISE
2.5mm HEX WRENCH
1
2
Turn on water supplies and check connections for leaks.
Remove AERATOR (1) with KEY (2) supplied.
Operate HOT and COLD HANDLES by pressing down on HANDLES.
Both Hot and Cold handles are set for approximately 8 second operating cycles.
Replace AERATOR (1).
TEST INSTALLED FITTING
6
PRESS HANDLE
DOWN TO OPERATE
SERVICE
1
4
3
2
REMOVE REPLACE
Clean
Washer
Collar down
O-RING
DETAIL “A”
Remove HANDLE (1) by removing INDEX BUTTON (2)
and SET SCREW (3) with a 2.5mm hex wrench.
Pull off HANDLE (1).
To increase cycle time, turn the white PLASTIC ADJUSTING
NUT (4) clockwise.
To decrease cycle time, turn the white PLASTIC
ADJUSTING NUT (4) counter-clockwise.
Replace HANDLE (1), SET SCREW (3) and
INDEX BUTTON (2). Test faucet for proper
operation and cycle time.
Remove HANDLE (1). Refer to Step 3 for handle removal.
Remove ACTUATOR ASSEMBLY (2).
Remove WASHER (3). Use small Hook to pull out VALVE
ASSEMBLY (4).
NOTE: The tip of the hook must catch on SURFACE (8)
to remove VALVE ASSEMBLY (4). Moderate force is
required. If the hook is too deep it will not remove
VALVE ASSEMBLY (4).
Open VALVE ASSEMBLY (4) by pulling VALVE BODY
TOP (5) off of VALVE BODY BOTTOM (6).
NOTE: There are three internal pieces including a spring.
Take caution not lose these components while opening
the valve body.
Ensure that O-RINGS (7) are free of any debris.
Remove O-RING (9), clean thoroughly, and ensure
the groove beneath is free of debris. Reinstall O-RINGS (9).
Reassemble VALVE ASSEMBLY (4) by pressing
VALVE BODY TOP (5) on to VALVE BODY (6)
until they lock with an audible snap.
Push VALVE ASSEMBLY (4) into faucet body. Place
WASHER (3) with collar facing down on top of
VALVE ASSEMBLY (4). See detail “A”. Thread VALVE
ACTUATOR (2) onto faucet. Torque VALVE ACTUATOR (2)
to 12-15 ft. lbs (15-20 Nm).
Replace HANDLE (1).
4
8
69
7
5
M968492 Rev.1.8 (8/19)
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR
WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID,
POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH
WITH A COARSE SURFACE.
METERING
LAVATORY
FAUCETS
CHROME 002
Appropriate finish code
051213-0070A
MOUNTING KIT
024220-0070A
SUPPLY NUT
M962390-002OA
HANDLE KIT
M962391-0070A
INDEX KIT
012111-0070A
TUBE & TEE
ASSEMBLY
033757-0070A
TEE MTG. KIT
030256-0070A
SPOUT MTG. KIT
012078-0070A
VALVE COUPLING KIT
PRODUCT NUMBERS
M922996-0020A
VR AERATOR, 1.0 GPM
066508-0020A
VR SPRAY, 0.5 GPM
A911836-0070A
SEAL WASHER
M952212-0020A
ACTUATOR UNIT
M952230-0070A
METERING VALVE
M964476-002OA
VALVE KIT
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
1340.825
1340.827
Product names listed herein are
trademarks of AS America, Inc.
© AS America, Inc. 2019
-
1
-
2
-
3
-
4
American Standard 1340.825.002 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
American Standard Cadet Deck-Mount Tub Filler 3985 User manual
-
-
-
-
-
-
-
-
-
