2. Airbus
  3. A340-300

Airbus A340-300, A340-200 Structural Repair Manual

  • Hello! I am an AI chatbot trained to assist you with the Airbus A340-300 Structural Repair Manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
STRUCTURALREPAIRMANUAL
Page201
53−00−13
Printed in Germany Jul01/05
STRINGERSANDSKINSTIFFENERS
1. General
Thistopiccontainsrepairproceduresfordamagetostringers.ForSection
andFRdesignationrefertoChapter53−00−00 PageBlock001.Therepairs
arelistedinTable201anddescribedinmoredetailinthefollowing
text.
NOTE: ForDamage/RepairDataRecordingrefertoChapter51−11−15.
NOTE: FordetaileddefinitionofRepairCategoriesrefertoChapter
51−11−14.
2. SafetyPrecautions
WARNING: OBEYTHEMANUFACTURERSINSTRUCTIONSWHENYOUUSECLEANINGAGENTS,
BONDINGANDADHESIVECOMPOUNDS,SEALANTS,SPECIALMATERIALSAND
STRUCTUREPAINTS.THESEMATERIALSAREDANGEROUS.
CAUTION: REFERTOEACHREPAIRTODETERMINETHEREPAIRAPPLICABILITY.
CAUTION: USEONLYSPECIFIEDCLEANINGMATERIALSANDSOLUTIONSORTHEIR
EQUIVALENTS.THESURFACEPROTECTIONCOULDBEDAMAGED,IFUNSPECI
FIEDMATERIALSAREUSED.ITISIMPORTANTTHATTHEMANUFACTURER’S
MIXING,APPLICATIONANDTREATMENTINSTRUCTIONSAREFOLLOWED.
CAUTION: TOPREVENTDAMAGETOTHESURFACEPROTECTION,MECHANICALANDELEC
TRICALSYSTEMS,THEAREASURROUNDINGTHEREPAIRMUSTBECOVERED
WITHPLASTICFOILMASKINGTAPE.
CAUTION: OBEYTHEGIVENINSPECTIONINSTRUCTIONREFERENCEWHICHLEADSTOTHE
APPLICABLEINSPECTIONPROGRAMDEFINEDINCHAPTERSTRUCTURALREPAIR
INSPECTIONS(SRI)OFTHESRM.
3. RepairScheme
REPAIRPROCEDURE PARAGRAPH FIGURE REPAIR
CATEGORY
INSPECTION
INSTRUCTION
REFERENCE
StringerRepair−Stringer
madefromDAN2,DAN50and
comparable
4.A. 201<1> B 53−00−13−2−001−00
BondingDefectsatStringer 4.B. 202<1> − −
StringerOuterFlangeRepair 4.C. B 53−00−13−2−002−00
−Cutout 203<1> −
−ReworkofCorrosion 204<1> −
Table201
STRUCTURALREPAIRMANUAL
Page202
53−00−13
Printed in Germany Jul01/05
REPAIRPROCEDURE
INSPECTION
INSTRUCTION
REFERENCE
REPAIR
CATEGORY
FIGUREPARAGRAPH
StringerRepair−Stringer
madefromDAN51B,DAN58Band
comparable
4.D. 205−208
<1> B 53−00−13−2−003−00
FloorAttachmentStringer
Repair 4.E. 209<2> B 53−00−13−2−004−00
Definitionofminimumdis
tancebetweenrepaircou
plingsorrepaircouplings
toexistingstructureparts
4.F. 210<1> A −
Table201
<1> validfor:
Section13and14
Section15:FR53.3−FR54,STGR31(LH)−STGR31(RH)(uppershell)
Section16−19
<2> validfor:
Section16−18
4. StringerandSkinStiffener−Repairs
CAUTION: THISREPAIRMUSTBEINSPECTEDATDEFINEDINTERVALS.THEACCORDING
INSPECTIONINSTRUCTIONREFERENCEISIIR53−00−13−2−001−00ANDIS
DESCRIBEDINCHAPTERSTRUCTURALREPAIRINSPECTIONS(SRI)OFTHE
SRM.INFORMYOURPLANNINGDEPARTMENTANDPROVIDETHEMWITHTHE
NECESSARYINFORMATION.
CAUTION: OBEYTHEREPAIREFFECTIVITYPERWEIGHTVARIANTANDAIRCRAFTTYPE
GIVENINTABLE202.
A. StringerRepair−StringermadefromDAN2,DAN50andcomparable
Therepairisapplicabletoformedandextrudedstringers−madefrom
DAN2,DAN50andcomparable−whenastringerisdamagedoraskinre
pairrequiresastringersplice.
NOTE: Therepairisapplicableonlyintheareasindicatedontherele
vantFigure.Therepaireffectivityofthisrepairisshownin
Table202.
STRUCTURALREPAIRMANUAL
Page203
53−00−13
Printed in Germany Jul01/05
AIRCRAFT WEIGHTVARIANT
A340−2XX 000,001,002
A340−2XX 021
A340−3XX 000,001,002,003,004
A340−3XX 020,021,024,026,027,028,050,051,052
RepairEffectivityperWeightVariantandAircraftType
Table202
NOTE: RefertotheWeightVariantIdentificationListgiveninthe
IntroductionoftheSRM.ThisTableshowsallnecessaryinformation
relatedtotheweightvariantandtheirmaximumvaluesandthe
modificationassociatedtotheaircrafttype.
(1) RepairMaterials
ITEM NOMENCLATURE QTY MATERIAL/REMARKS
1−4 asshowninIllustration − RefertoFigure201
− Sealant AR MaterialNo.09−013(Referto
Chapter51−35−00)
− CleaningAgent AR MaterialNo.11−003or11−004
(RefertoChapter51−35−00)
− Pretreatmentforpainting
(Chemicalconversioncoat
ing)
AR MaterialNo.13−002(Referto
Chapter51−35−00)
− Storagepreservation(Cor
rosionpreventivetemporary
protectivecompound)
AR MaterialNo.15−005A(Referto
Chapter51−35−00)
− Storagepreservation(Cor
rosionpreventivetemporary
protectivecompound)
AR MaterialNo.15−007(Referto
Chapter51−35−00)
− StructurePaint(Polyure
thaneprimer)
AR MaterialNo.16−001(Referto
Chapter51−35−00)
− StructurePaint(Polyure
thanetopcoat,grey)
AR MaterialNo.16−002(Referto
Chapter51−35−00)
− StructurePaint(Washprim
er)
AR MaterialNo.16−020(Referto
Chapter51−35−00)
− StructurePaint(flexible
polyurethane)
AR MaterialNo.16−021(Referto
Chapter51−35−00)
(2) RepairInstructions,refertoFigure201
(a) Removeallfastenersasnecessaryfortherepair.
STRUCTURALREPAIRMANUAL
Page204
53−00−13
Printed in Germany Jul01/04
CAUTION: IFTHECOMPLETEDAMAGEDSTRINGERSECTIONMUSTBECUTOUT,
USEAPLASTICWEDGETOCAREFULLYREMOVETHESECTIONAWAY
FROMTHESKIN.PLACEAMETALSHEETBETWEENSTRINGERAND
SKINTOAVOIDDAMAGETOTHESTRUCTUREDURINGTHECUTOUT
ACTION.
CAUTION: IFYOUMUSTHEATTHEREPAIRAREATOHELPSEPARATETHE
STRINGERCUTOUTFROMTHESKIN,DONOTUSEATEMPERATURE
MORETHAN130C°(266.0F°)
(b) Cutoutthedamagedsectionofthestringeranddeburrthe
edges.
NOTE: Ifpossible,leavethestringerflangeinpositionanduse
itasafillerpiece.
(c) Preparetherepairpartstosuitthedamagedareaanddeburr
edges,refertoFigure201.
(d) Attachtherepairpartsintheircorrectposition.Transferdrill
existingfastenerholesfromtheouterflangetotherepair
parts.Markanddrilladditionalholes.
NOTE: UsetransitionfitforHi−Lokfastenerinstallation(Refer
toChapter51−44−11).
(e) Removetherepairpartsanddeburrallfastenerholes.
WARNING: CLEANINGAGENT(MATERIALNO.11−003)ISDANGEROUS.
WARNING: CLEANINGAGENT(MATERIALNO.11−004)ISDANGEROUS.
(f) Cleantherepairpartsandtherepairareawithcleaningagent
(MaterialNo.11−003or11−004).
WARNING: STRUCTUREPAINT(MATERIALNO.16−020)ISDANGEROUS.
(g) Applywashprimer(MaterialNo.16−020)totherepairarea(Refer
toChapterChapter51−23−00).
WARNING: CHROMICACIDANODIZING(CAA)ISDANGEROUS.
WARNING: PRETREATMENTFORPAINTING(MATERIALNO.13−002)ISPOISON
OUS.
(h) PretreattherepairpartsbyChromicAcidAnodizing(CAA)oruse
chemicalconversioncoating(MaterialNo.13−002).
NOTE: ForprotectionbyCAAandtheapplicationofchemicalcon
versioncoatingrefertoChapter51−21−11.
WARNING: STRUCTUREPAINT(MATERIALNO.16−001)ISDANGEROUS.
(i) Applypolyurethaneprimer(MaterialNo.16−001)totherepair
parts.
STRUCTURALREPAIRMANUAL
Pages205/206
53−00−13
Printed in Germany Jul01/05
WARNING: STRUCTUREPAINT(MATERIALNO.16−002)ISDANGEROUS.
(j) Applypolyurethanetopcoat(MaterialNo.16−002)totherepair
parts.
WARNING: SEALANT(MATERIALNO.09−013)ISDANGEROUS.
(k) Applysealant(MaterialNo.09−013)tothematingsurfacesofthe
repairparts(RefertoChapter51−76−11.
(l) Attachtherepairpartsintheircorrectpositionandinstallall
fastenerswetwithsealant(MaterialNo.09−013).
NOTE: Installthefastenerswithintheapplicationlifeofthe
sealant.Ifthisisnotpossible,installatleastevery
thirdfastenerwithintheapplicationlifeofthesealant
(RefertoChapter51−76−00).
(m) Applyabeadofsealant(MaterialNo.09−013)totheedgesofthe
repairparts.
(n) Ifnecessary,applyflexiblepolyurethane(MaterialNo.16−021)
tothesealantbeads.
NOTE: RefertoChapter51−23−12forinformationaboutareasof
application.
WARNING: STRUCTUREPAINT(MATERIALNO.16−001)ISDANGEROUS.
(o) Restorethepaintfinisharoundtherepairarea.Usepolyurethane
primer(MaterialNo.16−001)andafterthatpolyurethanetopcoat
(MaterialNo.16−002).
WARNING: DONOTAPPLYSTORAGEPRESERVATION(MATERIALNO.15−005A)IN
AREAOFOXYGENEQUIPMENTANDOXYGENPIPES.
WARNING: STORAGEPRESERVATION(MATERIALNO.15−005A)ISDANGEROUS.
(p) Ifnecessary,applyacorrosionpreventivetemporaryprotective
compoundtotherepairarea.FirstapplyMaterialNo.15−005Aand
afterthatMaterialNo.15−007.
NOTE: BeforeapplicationofMaterialNo.15−007let
MaterialNo.15−005Adryforapproximately1hour.
NOTE: Thisisasupplementandmeanstopreventcorrosionin
areaswherespecialprotectionisrequired.RefertoChapter
51−23−12forinformationabouttheseareas.
STRUCTURALREPAIRMANUAL
Pages207/208
53−00−13
Printed in Germany Jul01/05
StringerRepair−StringermadefromDAN2,DAN50andcomparable
Figure201(sheet1)
STRUCTURALREPAIRMANUAL
Pages209/210
53−00−13
Printed in Germany Jul01/05
StringerRepair−StringermadefromDAN2,DAN50andcomparable
Figure201(sheet2)
STRUCTURALREPAIRMANUAL
Pages211/212
53−00−13
Printed in Germany Jul01/05
StringerRepair−StringermadefromDAN2,DAN50andcomparable
Figure201(sheet3)
STRUCTURALREPAIRMANUAL
Page213
53−00−13
Printed in Germany Jul01/04
Useof5/32in.Fastenerinsteadof3/16in.Fastener
Figure201(sheet4)
STRUCTURALREPAIRMANUAL
Page214
53−00−13
Printed in Germany Jul01/04
CAUTION: THISREPAIRINFORMATIONISAPPLICABLEASFOLLOWS:
−BEFOREMODIFICATION48827D42881
FORTHEEFFECTIVITYOFTHEGIVENMODIFICATIONREFERTOTHEMODIFI
CATION/SERVICEBULLETINLISTGIVENINChapter53−40−00 PageBlock
001.
B. BondingDefectsatStringer
NOTE: Thisrepairisapplicabletobondingdefectsatstringer.
(1) RepairMaterials
ITEM NOMENCLATURE QTY MATERIAL/REMARKS
− SpecialMaterial AR MaterialNo.05−027,(Referto
Chapter51−35−00)
− Sealant AR MaterialNo.09−013,(Referto
Chapter51−35−00)
− CleaningAgent AR MaterialNo.11−003,(Referto
Chapter51−35−00)
− CleaningAgent AR MaterialNo.11−004,(Referto
Chapter51−35−00)
− StructurePaint AR MaterialNo.16−001,(Referto
Chapter51−35−00)
− StructurePaint AR MaterialNo.16−002,(Referto
Chapter51−35−00)
− StructurePaint AR MaterialNo.16−003,(Referto
Chapter51−35−00)
− StructurePaint AR MaterialNo.16−020,(Referto
Chapter51−35−00)
(2) RepairInstructions,refertoFigure202.
(a) Determineareaofthedefectivebondingatthestringerusinga
bondtester.
WARNING: CLEANINGAGENT(MATERIALNO.11−003)ISDANGEROUS.
WARNING: CLEANINGAGENT(MATERIALNO.11−004)ISDANGEROUS.
(b) Removetheremainingsealantandcleantherepairareawith
cleaningagent(MaterialNo.11−003)orcleaningagent(Materi
alNo.11−004).
(c) Checktherepairareaforcorrosion.
NOTE: Ifcorrosionisfoundbetweenthestringerandtheskin,
thestringermustberepaired,refertoFigure201.
NOTE: ForremovalofcorrosionrefertoChapter51−74−00.
STRUCTURALREPAIRMANUAL
Page215
53−00−13
Printed in Germany Jul01/04
(d) Markoutthefastenerspacing,refertoFigure202.
NOTE: Selectthefastenerdiameterandthefastenerspacing,de
pendingontheareaintheaircraftandtheskinthickness,
refertoFigure202.Thehighervaluesoffastenerspacing
withinthegivenlimitsarepreferred.Rivetthedebonded
stringertotheskinwithinentireframebayandfourfas
tenersbeyondeachframe.
(e) Deburrthefastenerholes.
WARNING: CLEANINGAGENT(MATERIALNO.11−003)ISDANGEROUS.
WARNING: CLEANINGAGENT(MATERIALNO.11−004)ISDANGEROUS.
WARNING: STRUCTUREPAINT(MATERIALNO.16−020)ISDANGEROUS.
(f) Degreasethefastenerholeswithcleaningagent(Materi
alNo.11−003)orcleaningagent(MaterialNo.11−004)andapply
structurepaint(MaterialNo.16−020).
WARNING: SEALANT(MATERIALNO.09−013)ISDANGEROUS.
(g) Ifthebondedjointbetweenthestringerandtheskinhassepa
ratedcompletely,applysealant(MaterialNo.09−013),referto
Chapter51−76−00.
(h) Installthefastenerswetwithsealant(MaterialNo.09−013),re
fertoChapter51−76−00.
NOTE: Ensurethattheprocessofrivetingisfinishedduringthe
curingtimeofthesealant.
(i) Rivetthebondedstringer.
WARNING: STRUCTUREPAINT(MATERIALNO.16−003)ISDANGEROUS.
(j) Sealtheedgesofthestringerandthefastenerheadswithseal
ant(MaterialNo.09−013),refertoChapter51−76−00.
NOTE: Applystructurepaint(MaterialNo.16−003)tothesealant
beadinthelowershell,refertoChapter51−23−00.
WARNING: STRUCTUREPAINT(MATERIALNO.16−001)ISDANGEROUS.
(k) Applystructurepaint(MaterialNo.16−001)tothesurfaceofthe
internalrepairarea.
WARNING: STRUCTUREPAINT(MATERIALNO.16−002)ISDANGEROUS.
(l) Applystructurepaint(MaterialNo.16−002)totheinternalsur
faceoftherepairarea.
STRUCTURALREPAIRMANUAL
Page216
53−00−13
Printed in Germany Jul01/04
WARNING: DONOTAPPLYSPECIALMATERIAL(MATERIALNO.05−027)INAREA
ADJACENTTOOXYGENEQUIPMENTOROXYGENPIPES.
WARNING: SPECIALMATERIAL(MATERIALNO.05−027)ISDANGEROUS.
(m) Applyspecialmaterial(MaterialNo.05−027)orequivalenttothe
repairareainsidethelowershell,refertoChapter51−23−00.
STRUCTURALREPAIRMANUAL
Page217
53−00−13
Printed in Germany Jul01/04
BondingDefectsatStringers
Figure202
STRUCTURALREPAIRMANUAL
Page218
53−00−13
Printed in Germany Jul01/04
CAUTION: THISREPAIRMUSTBEINSPECTEDATDEFINEDINTERVALS.THEACCORDING
INSPECTIONINSTRUCTIONREFERENCEISIIR53−00−13−2−002−00ANDIS
DESCRIBEDINCHAPTERSTRUCTURALREPAIRINSPECTIONS(SRI)OFTHE
SRM.INFORMYOURPLANNINGDEPARTMENTANDPROVIDETHEMWITHTHE
NECESSARYINFORMATION.
CAUTION: OBEYTHEREPAIREFFECTIVITYPERWEIGHTVARIANTANDAIRCRAFTTYPE
GIVENINTABLE203.
C. StringerOuterFlangeRepair
Therepairisapplicabletoformedandextrudedstringersasfollows:
− ifastringerouterflangeisdamagedoraskinrepairrequiresa
stringerouterflangecutout(Figure203)
− iftheouterflangeofthestringeriscorroded(Figure204).
NOTE: Therepairisapplicableonlyintheareasindicatedontherele
vantFigure.Therepaireffectivityofthisrepairisshownin
Table
AIRCRAFT WEIGHTVARIANT
A340−2XX 000,001,002,
A340−2XX 021
A340−3XX 000,001,002,003,004
A340−3XX 020,021,024,026,027
RepairEffectivityperWeightVariantandAircraftType
Table203
NOTE: RefertotheWeightVariantIdentificationListgiveninthe
IntroductionoftheSRM.ThisTableshowsallnecessaryinformation
relatedtotheweightvariantandtheirmaximumvaluesandthe
modificationassociatedtotheaircrafttype.
STRUCTURALREPAIRMANUAL
Page219
53−00−13
Printed in Germany Jul01/04
(1) RepairMaterials
ITEM NOMENCLATURE QTY MATERIAL/REMARKS
1 Coupling − RefertoFigure203or204
2 FillerorShim − RefertoFigure203or204
− Sealant AR MaterialNo.09−013(Referto
Chapter51−35−00)
− CleaningAgent AR MaterialNo.11−003or11−004
(RefertoChapter51−35−00)
− Pretreatmentforpainting
(Chemicalconversioncoat
ing)
AR MaterialNo.13−002(Referto
Chapter51−35−00)
− Storagepreservation(Cor
rosionpreventivetemporary
protectivecompound)
AR MaterialNo.15−005A(Referto
Chapter51−35−00)
− Storagepreservation(Cor
rosionpreventivetemporary
protectivecompound)
AR MaterialNo.15−007(Referto
Chapter51−35−00)
− StructurePaint(Polyure
thaneprimer)
AR MaterialNo.16−001(Referto
Chapter51−35−00)
− StructurePaint(Polyure
thanetopcoat,grey)
AR MaterialNo.16−002(Referto
Chapter51−35−00)
− StructurePaint(Washprim
er)
AR MaterialNo.16−020(Referto
Chapter51−35−00)
− StructurePaint(flexible
polyurethane)
AR MaterialNo.16−021(Referto
Chapter51−35−00)
(2) RepairInstruction(RefertoFigure203and/or204)
(a) Removeallfastenersasnecessaryfortherepair.
(b) Reworkthedamagedpartofstringerouterflangeanddeburrthe
edges.
NOTE: Makesurenottodamagetheadjacentstructure.
(c) Ifthereiscorrosion(RefertoFigure204):
1 Examinetherepairareaandremoveallsignsofcorrosion(Re
fertoChapter51−74−00.
2 Checkremainingthicknessoftheareafromwhichthecorrosion
hasbeenremoved.Ifthethicknessislessthan0.8mm(0.03
in.)cutouttheouterflange.
(d) Preparetherepairpartsanddeburrtheedges(Refertothe
relevantFigure).
STRUCTURALREPAIRMANUAL
Page220
53−00−13
Printed in Germany Jul01/04
(e) Attachtherepairpartsintheircorrectposition.Transferdrill
existingfastenerholesfromtheouterflangetotherepair
parts.Markanddrilladditionalholes.
NOTE: UsetransitionfitforHi−Lokfastenerinstallation(Refer
toChapter51−44−11).
(f) Removetherepairpartsanddeburrallfastenerholes.
WARNING: CLEANINGAGENT(MATERIALNO.11−003)ISDANGEROUS.
WARNING: CLEANINGAGENT(MATERIALNO.11−004)ISDANGEROUS.
(g) Cleantherepairpartsandtherepairareawithcleaningagent
(MaterialNo.11−003or11−004).
WARNING: STRUCTUREPAINT(MATERIALNO.16−020)ISDANGEROUS.
(h) Applywashprimer(MaterialNo.16−020)totherepairarea(Refer
toChapter51−23−00).
WARNING: CHROMICACIDANODIZING(CAA)ISDANGEROUS.
WARNING: PRETREATMENTFORPAINTING(MATERIALNO.13−002)ISPOISON
OUS.
(i) PretreattherepairpartsbyChromicAcidAnodizing(CAA)oruse
chemicalconversioncoating(MaterialNo.13−002).
NOTE: ForprotectionbyCAAandtheapplicationofchemicalcon
versioncoatingrefertoChapter51−21−11.
WARNING: STRUCTUREPAINT(MATERIALNO.16−001)ISDANGEROUS.
(j) Applypolyurethaneprimer(MaterialNo.16−001)totherepair
parts.
WARNING: STRUCTUREPAINT(MATERIALNO.16−002)ISDANGEROUS.
(k) Applypolyurethanetopcoat(MaterialNo.16−002)totherepair
parts.
WARNING: SEALANT(MATERIALNO.09−013)ISDANGEROUS.
(l) Applysealant(MaterialNo.09−013)tothematingsurfacesofthe
repairparts(RefertoChapter51−76−11).
STRUCTURALREPAIRMANUAL
Pages221/222
53−00−13
Printed in Germany Jul01/04
WARNING: SEALANT(MATERIALNO.09−013)ISDANGEROUS.
(m) Attachtherepairpartsintheircorrectpositionandinstallall
fastenerswetwithsealant(MaterialNo.09−013).
NOTE: Installthefastenerswithintheapplicationlifeofthe
sealant.Ifthisisnotpossible,installatleastevery
thirdfastenerwithintheapplicationlifeofthesealant
(RefertoChapter51−76−00).
(n) Applyabeadofsealant(MaterialNo.09−013)totheedgesofthe
repairparts.
(o) Ifnecessary,applyflexiblepolyurethane(MaterialNo.16−021)to
thesealantbeads.
NOTE: RefertoChapter51−23−12forinformationaboutareasof
application.
WARNING: STRUCTUREPAINT(MATERIALNO.16−001)ISDANGEROUS.
WARNING: STRUCTUREPAINT(MATERIALNO.16−002)ISDANGEROUS.
(p) Restorethepaintfinisharoundtherepairarea.Usepolyurethane
primer(MaterialNo.16−001)andafterthatpolyurethanetopcoat
(MaterialNo.16−002).
WARNING: DONOTAPPLYSTORAGEPRESERVATION(MATERIALNO.15−005A)IN
AREAOFOXYGENEQUIPMENTANDOXYGENPIPES.
WARNING: STORAGEPRESERVATION(MATERIALNO.15−005A)ISDANGEROUS.
(q) Ifnecessary,applyacorrosionpreventivetemporaryprotective
compoundtotherepairarea.FirstapplyMaterialNo.15−005Aand
afterthatMaterialNo.15−007.
NOTE: BeforeapplicationofMaterialNo.15−007let
MaterialNo.15−005Adryforapproximately1hour.
NOTE: Thisisasupplementandmeanstopreventcorrosionin
areaswherespecialprotectionisrequired.RefertoChapter
51−23−12forinformationabouttheseareas.
STRUCTURALREPAIRMANUAL
Pages223/224
53−00−13
Printed in Germany Jul01/04
StringerOuterFlangeRepair−Cutout
Figure203(sheet1)
STRUCTURALREPAIRMANUAL
Pages225/226
53−00−13
Printed in Germany Jul01/04
StringerOuterFlangeRepair−Cutout
Figure203(sheet2)
STRUCTURALREPAIRMANUAL
Pages227/228
53−00−13
Printed in Germany Jul01/04
StringerOuterFlangeRepair−Cutout
Figure203(sheet3)
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/