Toro 21in Heavy-Duty Recycler/Rear Bagger Lawn Mower User manual

21in Heavy-Duty Recycler/Rear Bagger Lawn Mower
Toro
Brand
Toro
Model
21in Heavy-Duty Recycler/Rear Bagger Lawn Mower
Category
Lawnmowers
Type
User manual
FormNo.3401-798RevB
21inHeavy-DutyRecycler
®
/Rear
BaggerLawnMower
ModelNo.22297—SerialNo.316000001andUp
Registeratwww.Toro.com.
OriginalInstructions(EN)
*3401-798*B
WARNING
CALIFORNIA
Proposition65Warning
Thisproductcontainsachemicalorchemicals
knowntotheStateofCaliforniatocausecancer,
birthdefects,orotherreproductiveharm.
Theengineexhaustfromthisproduct
containschemicalsknowntotheStateof
Californiatocausecancer,birthdefects,
orotherreproductiveharm.
Introduction
Thisrotary-blade,walk-behindlawnmowerisintended
tobeusedbyresidentialhomeownersorprofessional,
hiredoperators.Itisdesignedprimarilyforcuttinggrass
onwell-maintainedlawnsonresidentialorcommercial
properties.Itisnotdesignedforcuttingbrushorfor
agriculturaluses.
Readthisinformationcarefullytolearnhowtooperateand
maintainyourproductproperlyandtoavoidinjuryand
productdamage.Youareresponsibleforoperatingthe
productproperlyandsafely.
YoumaycontactTorodirectlyatwww .Toro.comforproduct
andaccessoryinformation,helpndingadealer,ortoregister
yourproduct.
Wheneveryouneedservice,genuineToroparts,oradditional
information,contactanAuthorizedServiceDealerorToro
CustomerServiceandhavethemodelandserialnumbersof
yourproductready.Figure1identiesthelocationofthe
modelandserialnumbersontheproduct.Writethenumbers
inthespaceprovided.
Figure1
1.Modelandserialnumberlocation
ModelNo.
SerialNo.
Thismanualidentiespotentialhazardsandhassafety
messagesidentiedbythesafety-alertsymbol(Figure2),
whichsignalsahazardthatmaycauseseriousinjuryordeath
ifyoudonotfollowtherecommendedprecautions.
Figure2
1.Safety-alertsymbol
Thismanualuses2wordstohighlightinformation.
Importantcallsattentiontospecialmechanicalinformation
andNoteemphasizesgeneralinformationworthyofspecial
attention.
ItisaviolationofCaliforniaPublicResourceCode
Section4442or4443touseoroperatetheengineonany
forest-covered,brush-covered,orgrass-coveredlandunless
theengineisequippedwithasparkarrester,asdenedin
Section4442,maintainedineffectiveworkingorderorthe
engineisconstructed,equipped,andmaintainedforthe
preventionofre.
ThissparkignitionsystemcomplieswithCanadianICES-002.
Theenclosed
Engine Owner's Man ual
issuppliedfor
informationregardingtheUSEnvironmentalProtection
Agency(EPA)andtheCaliforniaEmissionControl
Regulationofemissionsystems,maintenance,and
warranty.Replacementsmaybeorderedthroughthe
enginemanufacturer.
NetTorque
Thegrossornettorqueofthisenginewaslaboratoryrated
bytheenginemanufacturerinaccordancewiththeSociety
ofAutomotiveEngineers(SAE)J1940.Asconguredto
meetsafety,emission,andoperatingrequirements,theactual
enginetorqueonthisclassofmowerwillbesignicantly
lower.Gotowww .Toro.comtoviewspecicationsonyour
mowermodel.
©2016—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
2
Contactusatwww.Toro.com.
PrintedintheUSA
AllRightsReserved
Contents
Safety...........................................................................3
GeneralSafety.........................................................3
SafetyandInstructionalDecals.................................5
Setup............................................................................7
1InstallingtheHandle.............................................7
2InstallingtheRecoil-StartRope...............................8
3FillingtheCrankcasewithOil.................................9
4AdjustingtheSelf-PropelDrive..............................10
5AssemblingtheGrassBag.....................................10
ProductOverview.........................................................11
Operation....................................................................11
CheckingtheEngine-OilLevel.................................11
FillingtheFuelTankwithGasoline...........................12
AdjustingtheCuttingHeight....................................12
StartingtheEngine.................................................12
ShuttingOfftheEngine..........................................13
OperatingtheSelf-PropelDrive...............................13
RecyclingtheClippings...........................................14
BaggingtheClippings.............................................14
OperatingTips......................................................15
Maintenance.................................................................16
RecommendedMaintenanceSchedule(s)......................16
EngineMaintenance..................................................17
ServicingtheAirCleaner.........................................17
ChangingtheEngineOil.........................................17
ChangingtheEngine-OilFilter.................................17
ServicingtheSparkPlug..........................................18
DriveSystemMaintenance.........................................19
AdjustingtheSelf-PropelDrive................................19
BrakeMaintenance....................................................19
AdjustingtheBlade-BrakeCable...............................19
BladeMaintenance.....................................................20
MaintainingtheBlade.............................................20
Cleaning...................................................................22
CleaningundertheMachine.....................................22
CleaningundertheBeltCover..................................22
CleaningtheWheels...............................................23
Storage........................................................................24
PreparingtheFuelSystem.......................................24
PreparingtheEngine..............................................24
GeneralInformation...............................................24
RemovingtheMachinefromStorage.........................24
Troubleshooting...........................................................25
Safety
ThismachinemeetsorexceedstheCPSCbladesafety
requirementsforwalk-behindrotarylawnmowers.
Improperlyusingormaintainingthislawnmowercan
resultininjury.Toreducethepotentialforinjury,
complywiththesesafetyinstructions.
Torodesignedandtestedthislawnmowerforreasonably
safeservice;however,failuretocomplywiththefollowing
instructionsmayresultinpersonalinjury.
WARNING
Engineexhaustcontainscarbonmonoxide,an
odorless,deadlypoisonthatcankillyou.
Donotruntheengineindoorsorinanenclosed
area.
Toensuremaximumsafety,bestperformance,andto
gainknowledgeoftheproduct,itisessentialthatyou
andanyotheroperatorofthelawnmowerreadand
understandthecontentsofthismanualbeforetheengine
iseverstarted.Payparticularattentiontothesafety-alert
symbol(Figure2)whichmeansCaution,Warning,or
Danger.Readandunderstandtheinstructionbecause
ithastodowithsafety.Failuretocomplywiththe
instructionmayresultinpersonalinjury.
GeneralSafety
Thismachineiscapableofamputatinghandsandfeetand
ofthrowingobjects.Failuretoobservethefollowingsafety
instructionscouldresultinseriousinjuryordeath.
Thefollowinginstructionshavebeenadaptedfromthe
ANSI/OPEIB71.4-2012standard.
Training
•ReadtheOperator'sManualandothertrainingmaterial.If
theoperator(s)ormechanic(s)cannotreadEnglish,itis
theowner'sresponsibilitytoexplainthismaterialtothem.
•Becomefamiliarwiththesafeoperationoftheequipment,
operatorcontrols,andsafetysigns.
•Alloperatorsandmechanicsshouldbetrained.The
ownerisresponsiblefortrainingtheusers.
•Neverletchildrenoruntrainedpeopleoperateorservice
theequipment.Localregulationsmayrestricttheageof
theoperator.
•Theowner/usercanpreventandisresponsiblefor
accidentsorinjuriesoccurringtothemselves,other
people,orproperty.
Preparation
•Useonlyaccessoriesandattachmentsapprovedbythe
manufacturer.
3
•Wearappropriateclothingincludingeyeprotection,
slip-resistant,substantialfootwear,andhearingprotection.
Tiebacklonghair.Donotwearjewelry.
•Inspecttheareawheretheequipmentistobeusedand
removeallobjects,suchasrocks,toys,andwire,which
canbethrownbythemachine.
•Checkthatoperator'spresencecontrols,safetyswitches,
andshieldsareattachedandfunctioningproperly.Donot
operatethemachineunlesstheyarefunctioningproperly.
SafeHandlingofFuels
•Toavoidpersonalinjuryorpropertydamage,use
extremecareinhandlinggasoline.Gasolineisextremely
ammableandthevaporsareexplosive.
•Extinguishallcigarettes,cigars,pipes,andothersources
ofignition.
•Useonlyanapprovedfuelcontainer.
•Neverremovethefuelcaporaddfuelwiththeengine
running.
•Allowtheenginetocoolbeforerefueling.
•Neverrefuelthemachineindoors.
•Neverstorethemachineorthefuelcontainerwherethere
isanopename,spark,orpilotlight,suchasonawater
heateroronotherappliances.
•Neverllcontainersinsideavehicleoronatruckor
trailerbedwithaplasticliner.Alwaysplacecontainerson
thegroundawayfromyourvehiclebeforelling.
•Removetheequipmentfromthetruckortrailerand
refuelitontheground.Ifthisisnotpossible,thenrefuel
suchequipmentwithaportablecontainerratherthan
fromafueldispensernozzle.
•Keepthenozzleincontactwiththerimofthefueltank
orcontaineropeningatalltimesuntilfuelingiscomplete.
•Donotuseanozzlelock-opendevice.
•Ifyouspillfuelonclothing,changetheclothing
immediately.
•Neveroverllthefueltank.Replacethefuelcapand
tightenitsecurely.
Operation
•Neverrunanengineinanenclosedarea.
•Operatethemachineonlyingoodlight,keepingaway
fromholesandhiddenhazards.
•Starttheengineonlyfromtheoperatingposition.
•Besureofyourfooting,especiallywhenbackingup.
Walk,don'trun.Neveroperatethemachineonwetgrass.
Reducedfootingcouldcauseslipping.
•Slowdownanduseextracareonhillsides.Besureto
travelsidetosideonhillsides.Turfconditionscanaffect
thestabilityofthemachine.Usecautionwhileoperating
themachineneardrop-offs.
•Donotoperatethemachinewithouteitherthegrass
catcherortheguardinplace.
•Donotchangetheenginegovernorsettingoroverspeed
theengine.
•Stopthemachineonlevelgroundandshutofftheengine
beforeleavingtheoperatingpositionforanyreason,
includingemptyingthecatcheroruncloggingthechute.
•Stopthemachineandinspectthebladeafterstriking
objectsorifanabnormalvibrationoccurs.Make
necessaryrepairstothemachinebeforeresuming
operation.
•Keephandsandfeetawayfromthecuttingunits.
•Lookbehindanddownbeforebackinguptobesureof
aclearpath.
•Keeppetsandbystandersaway.
•Slowdownandusecautionwhencrossingroadsand
sidewalks.Stopthebladeifyouarenotmowing.
•Beawareofthemachinedischargedirectionanddonot
pointitatanyone.
•Donotoperatethemachinewhiletired,ill,orunderthe
inuenceofalcoholordrugs.
•Usecarewhenloadingorunloadingthemachineintoa
trailerortruck.
•Usecarewhenapproachingblindcorners,shrubs,trees,
orotherobjectsthatmayobscurevision.
MaintenanceandStorage
•Shutofftheengineanddisconnectthespark-plugwire.
Waitforallmovementtostopbeforeadjusting,cleaning,
orrepairingthemachine.
•Cleangrassanddebrisfromthecuttingunit,drive,
mufer,andenginetohelppreventres.Cleanupoil
orfuelspills.
•Lettheenginecoolbeforestoringthemachine,anddo
notstoreitnearaame.
•Shutoffthefuelwhilestoringortransportingthe
machine.Donotstorefuelnearamesordrainfuel
indoors.
•Neverallowuntrainedpersonneltoservicethemachine.
•Removethespark-plugwirebeforemakinganyrepairs.
•Usecarewhencheckingtheblade.Wrapthebladeor
weargloves,andusecautionwhenservicingtheblade.
Onlyreplacetheblade;neverstraightenorweldit.
•Keephandsandfeetawayfrommovingparts.Ifpossible,
donotmakeadjustmentstothemachinewhiletheengine
isrunning.
•Keepallpartsingoodworkingconditionandallhardware
tightened.Replaceallwornordamageddecals.
•Tobestprotectyourinvestmentandmaintainoptimal
performanceofyourToroequipment,countonToro
genuineparts.Whenitcomestoreliability,Torodelivers
replacementpartsdesignedtotheexactengineering
specicationsofourequipment.Forpeaceofmind,insist
onTorogenuineparts.
4
Hauling
•Usecarewhenloadingorunloadingthemachineintoa
trailerortruck.
•Usefull-widthrampsforloadingthemachineintoa
traileroratruck.
•Tiethemachinedownsecurelyusingstraps,chains,cable,
orropes.Boththefrontandtherearstrapsshouldbe
directeddownandoutwardfromthemachine.
SafetyandInstructionalDecals
Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaofpotential
danger.Replaceanydecalthatisdamagedorlost.
Manufacturer'sMark
1.Indicatesthebladeisidentiedasapartfromtheoriginal
machinemanufacturer.
94-8072
116-7583
1.Warning–ReadtheOperator’sManual.Donotoperatethis
machineunlessyouaretrained.
4.Cutting/dismembermenthazardofhandorfoot,mower
blade—stayawayfrommovingparts;keepallguardsinplace.
2.Thrownobjecthazard—keepbystandersasafedistancefrom
themachine.
5.Warning—wearhearingprotection.
3.Thrownobjecthazard—Donotoperatethemowerwithoutthe
reardischargeplugorbaginplace.
6.Cutting/dismembermenthazardofhandorfoot,mower
blade—Donotoperateupanddownslopes;operateside
tosideonslopes;shutofftheenginebeforeleavingthe
operatingposition—pickupobjectsthatcouldbethrownby
theblades;andlookbehindyouwhenbackingup.
117–2718
5
125-8404
1.Pushtheprimeronce.2.Pulltherecoil-starthandle.
130-6722
1.Attention—readtheOperator'sManual.
130-9670
1.Severinghazardofhandorfoot;mowerblade—keepaway
frommovingparts;keepallguardsandshieldsinplace.
6
Setup
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescription
Qty.
Use
Handle1
Hex-head-angebolt(5/16x1-1/2
inches)
2
Carriagebolt(5/16x1-1/2inches)
2
1
Flangenut(5/16inch)
4
Installthehandle.
2
Nopartsrequired
–
Installthestarterrope.
3
Nopartsrequired
–
Fillthecrankcasewithoil.
4
Nopartsrequired
–
Adjusttheself-propeldrive.
5
Nopartsrequired
–
Assemblethegrassbag.
Note:Determinetheleftandrightsidesofthemachine
fromthenormaloperatingposition.
1
InstallingtheHandle
Partsneededforthisprocedure:
1Handle
2
Hex-head-angebolt(5/16x1-1/2inches)
2
Carriagebolt(5/16x1-1/2inches)
4
Flangenut(5/16inch)
Procedure
1.Removethecableguardfromthehandle(Figure3)by
removingthe2carriageboltsand2locknutsthathold
thecableguardtothehandle.
Figure3
1.Cableguard4.Flangenut—5/16inch(2)
2.Locknut(2)5.Hex-head-ange
bolt—5/16x1-1/2inches
(2)
3.Carriagebolt—1/4x1-1/2
inches(2)
Note:Savetheguard,thecarriagebolts,andthe
locknutssothatyoucaninstallthemontothehandle
laterinthisprocedure.
2.Installthehandleendsontothemowerhousingwith
2hex-head-angebolts(5/16x1-1/2inches)and2
angenuts(5/16inch)asshowninFigure3.
7
3.Setthemachinetothedesiredcuttingheight;referto
AdjustingtheCuttingHeight(page12).
4.Routethecontrolcablesbetweenthedeckandthe
handletoprotectthecablesfrombeingdamaged
(Figure4).
Figure4
1.Cableguard3.Cable(s)
2.Handle
5.Standintheoperatingpositiontodeterminethehandle
heightthatismostcomfortableforyou(Figure5).
Figure5
1.Handle4.Mediumhandleheight
2.Handlebracket(2)
5.Lowesthandleheight
3.Highesthandleheight
6.Securethehandleontothehandlebracketsatyour
desiredhandleheightwith2carriagebolts(5/16x
1-1/2inches)and2angenuts(5/16inch)asshown
inFigure6.
Important:Ensurethattheboltheadsareon
theinsideofthehandleandthenutsareonthe
outsideofthehandle.
Figure6
1.Carriagebolt—5/16x
1-1/2inches(2)
3.Flangenut—5/16inch(2)
2.Handlebracket(2)
7.Positionthecableguardontothehandlewiththe
cable(s)insidetheguard,andsecuretheguardtothe
handlewiththe2carriageboltsandthe2locknutsthat
youpreviouslyremoved(Figure3).
Important:Ensurethatyoudonotpinchthe
cable(s)tothehandlewhenyouinstallthecable
guardsontothehandle.
2
InstallingtheRecoil-Start
Rope
NoPartsRequired
Procedure
Pulltherecoil-startropethroughtheropeguideonthe
handle(Figure7).
8
Figure7
1.Recoil-startrope2.Ropeguide
Note:Tomaketheropeeasiertoinstall,squeezethe
blade-controlbaronthehandle.
3
FillingtheCrankcasewithOil
NoPartsRequired
Procedure
Theenginecrankcaseisshippedwithoutoil.Before
startingtheengine,llthecrankcasewithoil.Theengine
crankcase(withoillter)canhold0.85L(29oz)ofoil.Use
onlyhigh-qualitySAE10W-30weightdetergentoilthathas
theAmericanPetroleumInstitute(API)serviceclassication
SH,SJ,orequivalent.
Beforeeachuse,ensurethattheoillevelisbetweentheAdd
andtheFullmarksonthedipstick(Figure8).
Figure8
1.Dipstick3.Addmark
2.Fullmark
Note:Whenthecrankcaseisempty,pourabout3/4ofthe
crankcasecapacityofoilinthecrankcase,thenfollowthe
procedureinthissection.
1.Movethemachineontoalevelsurface.
2.Cleanaroundthedipstick(Figure8).
3.Removethedipstickbyrotatingthecap
counterclockwiseandpullingitout.
4.Wipethedipstickcleanwithacleancloth.
5.Insertthedipstickintothellerneck,thenremovethe
dipstick.
6.Readtheoillevelonthedipstick.
•IftheoillevelisbelowtheAddmarkonthe
dipstick,slowlypourasmallamountofoilinto
theoil-lltube,wait3minutes,andrepeatsteps4
9
through6untiltheoillevelisattheFullmarkon
thedipstick.
•IftheoillevelisabovetheFullmarkonthe
dipstick,draintheexcessoiluntiltheoillevelon
thedipstickisattheFullmark.
Important:Iftheoillevelinthecrankcaseis
toolowortoohighandyouruntheengine,
youmaydamagetheengine.
7.Insertthedipstickintothellerneckandrotatethecap
clockwiseuntilitistight.
4
AdjustingtheSelf-PropelDrive
NoPartsRequired
Procedure
Important:Youmustadjusttheself-propel-drivecable
beforeyouoperatethemachineforthersttime.Refer
toAdjustingtheSelf-PropelDrive(page19).
5
AssemblingtheGrassBag
NoPartsRequired
Procedure
1.SlipthegrassbagovertheframeasshowninFigure9.
1
2
3
g027289
Figure9
1.Handle
3.Grassbag
2.Frame
Note:Donotslipthebagoverthehandle(Figure9).
2.Hookthebottomchannelofthebagontothebottom
oftheframe(Figure10).
g027290
Figure10
3.Hookthetopandsidechannelsofthebagontothetop
andsidesoftheframe,respectively(Figure10).
10
ProductOverview
Figure11
1.Handle
7.Sparkplug
2.Blade-controlbar
8.Cutting-heightlever(4)
3.Reardoor
9.Oilll/dipstick
4.Fuel-tankcap
10.Grassbag
5.Aircleaner11.Recoil-starthandle
6.Primer
Operation
Note:Determinetheleftandrightsidesofthemachine
fromthenormaloperatingposition.
Eachtimebeforeyoumow,ensurethattheself-propeldrive
andtheblade-controlbaroperateproperly.Whenyourelease
theblade-controlbar,thebladeandtheself-propeldrive
shouldstop.Iftheydonot,contactanAuthorizedService
Dealer.
CAUTION
Thismachineproducessoundlevelsinexcessof
85dBAattheoperator'searandcancausehearing
lossthroughextendedperiodsofexposure.
Wearhearingprotectionwhenoperatingthis
machine.
Figure12
1.Warning—wearhearingprotection.
CheckingtheEngine-OilLevel
ServiceInterval:Beforeeachuseordaily—Checkthe
engine-oillevel.
Beforeyouusethemachine,ensurethattheoillevelis
betweentheAddandtheFullmarksasshownonthedipstick
(Figure13).
Figure13
1.Dipstick3.Addmark
2.Fullmark
11
IftheoillevelisbelowtheAddmark,addoil.Referto3
FillingtheCrankcasewithOil(page9).
FillingtheFuelTankwith
Gasoline
DANGER
Gasolineisextremelyammableandexplosive.A
reorexplosionfromgasolinecanburnyouand
others.
•Topreventastaticchargefromignitingthe
gasoline,placethecontainerand/ormachine
directlyonthegroundbeforelling,notina
vehicleoronanobject.
•Fillthetankoutdoorswhentheengineiscold.
Wipeupspills.
•Donothandlegasolinewhensmokingoraround
anopenameorsparks.
•Storegasolineinanapprovedfuelcontainer,out
ofthereachofchildren.
•Forbestresults,useonlyclean,fresh(lessthan30days
old),unleadedgasolinewithanoctaneratingof87or
higher((R+M)/2ratingmethod).
•Oxygenatedfuelwithupto10%ethanolor15%MTBE
byvolumeisacceptable.
•Ethanol:Gasolinewithupto10%ethanol(gasohol)
or15%MTBE(methyltertiarybutylether)byvolume
isacceptable.EthanolandMTBEarenotthesame.
Gasolinewith15%ethanol(E15)byvolumeisnot
approvedforuse.Neverusegasolinethatcontains
morethan10%ethanolbyvolume,suchasE15
(contains15%ethanol),E20(contains20%ethanol),or
E85(containsupto85%ethanol).Usingunapproved
gasolinemaycauseperformanceproblemsand/orengine
damagewhichmaynotbecoveredunderwarranty.
•Donotusegasolinecontainingmethanol.
•Donotstorefueleitherinthefueltankorinfuel
containersoverthewinterunlessyouuseafuelstabilizer.
•Donotaddoiltogasoline.
Important:Toreducestartingproblems,addfuel
stabilizertothefuelallseason,mixingitwithgasoline
lessthan30daysold.
Note:Thecapacityofthefueltankis3.8L(1.0USgallon).
AdjustingtheCuttingHeight
Youcanchangethecuttingheightateachwheelbyadjusting
acutting-heightlever.Cuttingheightsare25mm(1inch),38
mm(1-1/2inches),51mm(2inches),64mm(2-1/2inches),
76mm(3inches),89mm(3-1/2inches),102mm(4inches),
114mm(4-1/2inches).
DANGER
Adjustingthecutting-heightleverscouldbringyour
handsintocontactwithamovingbladeandresult
inseriousinjury.
•Shutofftheengineandwaitforallmovementto
stopbeforeadjustingthecuttingheight.
•Donotputyourngersunderthehousingwhen
adjustingthecuttingheight.
1.Pullthecutting-heightlevertowardthewheel(Figure
14)andmovethelevertothedesiredsetting.
Figure14
1.Rearcutting-heightlever(2)
2.Frontcutting-heightlever(2)
2.Releasethecutting-heightleverandseatitsecurelyin
thenotch.
3.Adjustallthewheelstothesamecutting-heightsetting.
StartingtheEngine
1.Connectthespark-plugwiretothesparkplug.
2.Openthefuelvalve(Figure15).
Figure15
1.Fuelvalve
3.Firmlypushintheprimer(Figure16),holdingthe
primerbulbinfor1second.
12
Figure16
1.Primer
4.Holdtheblade-controlbarintheRun/Shiftposition,
about2.5cm(1inch)belowthehandle(Figure17).
Figure17
1.Handle3.Blade-controlbarinthe
Run/Shiftposition—about
2.5cm(1inch)belowthe
handle
2.Blade-controlbarinthe
Run/Driveposition
4.Blade-controlbarinthe
Stopposition
5.Pullthestarterhandlelightlyuntilyoufeelresistance,
pullitsharply,thenallowittoreturnslowlytotherope
guideonthehandle.
Note:Iftheenginedoesnotstart,repeatsteps3
through5.
ShuttingOfftheEngine
Releasetheblade-controlbar.Boththeengineandtheblade
shouldstopwithin3seconds.Iftheydonot,contactan
AuthorizedServiceDealer.
Note:Closethefuelvalve(Figure15)ifyouwillnotbe
startingtheenginesoonafterward.
OperatingtheSelf-Propel
Drive
Thismachinehas3groundspeeds:1(slow),2(medium),
and3(fast);italsohasaNeutral(N)position.The
self-propel-driveleverislocatedbelowandbehindthefuel
tank(Figure18).
Figure18
1.Self-propel-drivelever
1.Movetheself-propel-drivelevertothedesiredground
speed.
2.Starttheengine.
3.Squeezetheblade-controlbaragainstthehandletothe
Run/Driveposition(Figure19).
Figure19
1.Handle3.Blade-controlbarinthe
Run/Shiftposition—about
2.5cm(1inch)belowthe
handle
2.Blade-controlbarinthe
Run/Driveposition
4.Blade-controlbarinthe
Stopposition
Important:Shiftingspeedswhilesqueezing
theblade-controlbaragainstthehandlein
theRun/Drivepositioncoulddamagethe
transmission.Movetheblade-controlbartothe
13
Run/Shiftposition(Figure19)wheneveryou
changethegroundspeed.
Note:Youcanvarythegroundspeedbyincreasingor
decreasingthedistancebetweentheblade-controlbar
andthehandle.Lowerthebartodecreasetheground
speedwhenyouaremakingaturnorifthemachine
ismovingtoofastforyou.Ifyoulowerthebartoo
far,themachinestopsself-propelling.Squeezethe
barclosertothehandletoincreasethegroundspeed.
Whenyouholdthebartightagainstthehandle,the
machineself-propelsatthemaximumgroundspeed.
Movetheself-propel-drivelevertotheNEUTRAL
positionwhenyouusethemachinefortrimming.
RecyclingtheClippings
Thismachinecomesfromthefactoryreadytorecyclegrass
andleafclippingsbackintothelawn.Topreparethemachine
torecycle:
•Ifthegrassbagisonthemachine,removeit;referto
RemovingtheGrassBag(page15).
•Iftherear-dischargeplugisnotinstalled,gripitby
thehandle,raisethereardoor,andinsertitintothe
rear-dischargechuteuntilthelatchlocksintoplace
(Figure20).
Figure20
1.Rear-dischargeplug2.Reardoor
WARNING
Operatingthemachinetorecyclelawnclippings
withoutthepluginplaceallowsobjectstobe
throwntowardyouorbystanders.Also,contactwith
thebladescouldoccur.Thrownobjectsorblade
contactcancauseseriousinjuryordeath.
Ensurethattherear-dischargeplugisinplace
beforeyourecycletheclippings.Neverengagethe
bladeswithouteithertherear-dischargeplugorthe
grassbaginstalledonthemachine.
BaggingtheClippings
Usethegrassbagwhenyouwanttocollectgrassandleaf
clippingsfromthelawn.
WARNING
Aworngrassbagcouldallowsmallstonesand
othersimilardebristobethrowntowardyouor
bystanders,resultinginseriouspersonalinjuryor
death.
Checkthegrassbagfrequently.Ifitisdamaged,
installanewTororeplacementbag.
WARNING
Thebladesaresharp;contactingthebladescan
resultinseriouspersonalinjury.
Shutofftheengineandwaitforallmovingpartsto
stopbeforeleavingtheoperatingposition.
InstallingtheGrassBag
1.Shutofftheengineandwaitforallmovingpartsto
stop.
2.Raiseandholdupthereardoor(Figure21).
Figure21
1.Reardoor
3.Notch(2)
2.Bag-rodend(2)
3.Removetherear-dischargeplugbypushinginthelatch
withyourthumbandpullingtheplugoutfromthe
machine(Figure20).
4.Installthebag-rodendsintothenotchesatthebaseof
thehandle,androckthebagbackandforthtoensure
thatthebag-rodendsareseatedatthebottomofboth
notches(Figure21).
5.Lowerthereardooruntilitrestsonthegrassbag.
14
RemovingtheGrassBag
DANGER
Themachinecanthrowgrassclippingsandother
objectsthroughanopeninginthemowerhousing.
Objectsthrownwithenoughforcecouldcause
seriouspersonalinjuryordeathtoyouorto
bystanders.
•Neverremovethegrassbagandthenstartthe
enginewithoutthedischargepluginstalledon
themachine.
•Neveropenthereardooronthemachinewhen
theengineisrunning.
1.Shutofftheengineandwaitforallmovingpartsto
stop.
2.Raisethereardoor.
3.Removethebagrodonthegrassbagfromthenotches
atthebaseofthehandle(Figure21).
4.Installthedischargeplug;refertoRecyclingthe
Clippings(page14).
5.Lowerthereardoor.
OperatingTips
GeneralTips
•Reviewthesafetyinstructionsandreadthismanual
carefullybeforeoperatingthemachine.
•Cleartheareaofsticks,stones,wire,branches,andother
debristhatthebladecouldhitandthrow.
•Keepeveryone,especiallychildrenandpets,awayfrom
theareaofoperation.
•Avoidstrikingtrees,walls,curbs,orothersolidobjects.
Neverdeliberatelymowoveranyobject.
•Ifthemachinestrikesanobjectorstartstovibrate,
immediatelyshutofftheengine,disconnectthewirefrom
thesparkplug,andexaminethemachinefordamage.
•Maintainasharpbladethroughoutthecuttingseason.
Periodicallyledownnicksontheblade.
•ReplacethebladewhennecessarywithanoriginalToro
replacementblade.
•Mowonlydrygrassorleaves.Wetgrassandleavestend
toclumpontheyardandcancausethemachinetoplug
ortheenginetostall.
WARNING
Wetgrassorleavescancauseseriousinjuryif
youslipandcontacttheblade.
Mowonlyindryconditions.
•Cleanunderthemachineaftereachmowing;referto
CleaningundertheMachine(page22).
•Keeptheengineingoodrunningcondition.
•Cleantheairlterfrequently.Mulchingstirsupmore
clippingsanddustwhichclogstheairlterandreduces
engineperformance.
•Settheenginespeedtothefastestpositionforthebest
cuttingresults.
WARNING
Operatingamachinewithitsenginerunning
ataspeedgreaterthanthefactorysettingcan
causethemachinetothrowapartoftheblade
orenginetowardyouorbystanders,resultingin
seriouspersonalinjuryordeath.
–Donotchangetheenginespeedsetting.
–Ifyoususpecttheenginespeedisfaster
thannormal,contactanAuthorizedService
Dealer.
CuttingGrass
•Grassgrowsatdifferentratesatdifferenttimesofthe
year.Inthesummerheat,itisbesttocutgrassatthe64
mm(2-1/2inch),76mm(3inch),or89mm(3-1/2inch)
cutting-heightsettings.Cutonlyaboutathirdofthegrass
bladeatatime.Donotcutbelowthe64mm(2-1/2inch)
settingunlessthegrassissparseoritislatefallwhen
grassgrowthbeginstoslowdown.
•Whencuttinggrassover15cm(6inches)tall,rstmow
atthehighestcuttingheightsettingandwalkslower;then
mowagainatalowersettingforthebestlawnappearance.
Ifthegrassistoolongandtheleavesclumpontopofthe
lawn,themachinemayplugandcausetheenginetostall.
•Alternatethemowingdirection.Thishelpsdispersethe
clippingsoverthelawnforevenfertilization.
Ifthenishedlawnappearanceisunsatisfactory,try1or
moreofthefollowing:
•Sharpentheblade.
•Walkataslowerpacewhilemowing.
•Raisethecuttingheightonyourmachine.
•Cutthegrassmorefrequently.
•Overlapcuttingswathsinsteadofcuttingafullswath
witheachpass.
CuttingLeaves
•Aftercuttingthelawn,ensurethathalfofthelawnshows
throughthecutleafcover.Youmayneedtomakemore
thanasinglepassovertheleaves.
•Forlightleafcoverage,setallthewheelsatthesame
cuttingheightsetting.
•Slowdownyourmowingspeedifthemachinedoesnot
cuttheleavesnelyenough.
15
Maintenance
Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.
RecommendedMaintenanceSchedule(s)
MaintenanceService
Interval
MaintenanceProcedure
Aftertherst8hours
•Changetheengineoilandtheoillter.
Aftertherst25hours
•Tightenanyloosefasteners.
Beforeeachuseordaily
•Checktheengine-oillevel.
•Inspectthemowerbladesforwearordamage.
•Inspecttheacceleratorforwearordamage.
•Removegrassclippingsanddirtfromunderthemachine.
•Checkthestoppingtimeofthebladebrake.Theblademuststopwithin3seconds
ofreleasingtheblade-controlbar;ifitdoesnot,contactanAuthorizedService
Dealerforrepair.
•Checkforlooseormissingfastenersontheengine.
•Checkforfueloroilleaks.
•Checkorcleantherecoilstarterandtheair-intakescreen.
Every25hours
•Cleanthefoampre-cleaner(morefrequentlyindustyconditions).
Every40hours
•Cleanthewheelsandgears.
Every50hours
•Sharpenorreplacetheblade.Maintainitmorefrequentlyiftheedgedullsquicklyin
roughorinsandyconditions.
•Removegrassclippingsanddebrisfromunderthebeltcover.
Every100hours
•Changetheengineoil.
•Inspect,clean,andadjustthesparkpluggap;replacethesparkplugifnecessary.
•Tightenanyloosefasteners.
•Checkorcleantherecoilstarterandtheair-intakescreen.
Every200hours
•Changetheengine-oillter.
•Haveanauthorizedengineservicingdealercheckforleaksinthefuelsystemand/or
adeterioratingfuelhose.Replacepartsifnecessary.
Every300hours
•Replacethepaperairlter(morefrequentlyindustyconditions).
•Cleanthecylinderandthecylinder-headns.
•Haveanauthorizedengineservicingdealercheckandadjusttheengineidlespeed.
•Haveanauthorizedengineservicingdealercleanthecombustionchamber.
•Haveanauthorizedengineservicingdealercheckandadjustthevalveclearance.
•Haveanauthorizedengineservicingdealercleanandlapthevalveseatingsurface.
Important:Refertoyourengineowner'smanualforadditionalmaintenanceprocedures.
CAUTION
Ifyouleavethewireonthesparkplug,someonecouldaccidentlystarttheengineandseriouslyinjure
youorbystanders.
Disconnectthewirefromthesparkplugbeforeyoudoanymaintenance.Setthewireasidesothatitdoes
notaccidentlycontactthesparkplug.
16
EngineMaintenance
ServicingtheAirCleaner
ServiceInterval:Every25hours—Cleanthefoam
pre-cleaner(morefrequentlyindusty
conditions).
Every300hours—Replacethepaperairlter(more
frequentlyindustyconditions).
Important:Donotoperatetheenginewithoutthe
airlterassemblyinplace;otherwise,extremeengine
damagewilloccur.
1.Shutofftheengineandwaitforallmovingpartsto
stop.
2.Disconnectthewirefromthesparkplug.
3.Removethecoverandcleanitthoroughly(Figure22).
Figure22
1.Cover
3.Air-cleanerbase
2.Foampre-cleanerand
paperairlter
4.Removeandthefoampre-cleanerandthepaper-air
lterfromtheair-cleanerbase(Figure22)
5.Removethefoampre-cleanerfromthepaperairlter,
andwashthefoampre-cleanerwithamilddetergent
andwater,thenblotitdry.
6.Inspectthepaperairlter,andreplaceitifitis
excessivelydirty.
Important:Donottrytocleanapaperlter.
7.Installthefoampre-cleanerontothepaperairlter.
8.Installthefoampre-cleanerandpaperairlteronto
theair-cleanerbase.
9.Installthecover.
ChangingtheEngineOil
ServiceInterval:Aftertherst8hours
Every100hours
OilCapacity
Withoillter0.85L(29oz)
Withoutoillter0.65L(22oz)
1.Runtheenginetowarmtheengineoil.
Note:Warmoilowsbetterandcarriesmore
contaminants.
WARNING
Oilmaybehotafterenginehasbeenrun,and
contactwithhotoilcancauseseverepersonal
injury.
Avoidcontactingthehotengineoilwhenyou
drainit.
2.Shutofftheengineandwaitforallmovingpartsto
stop.
3.Disconnectthewirefromthesparkplug.
4.Closethefuelvalve(Figure15).
5.Drainthegasolinefromthefueltank.
6.Placeasuitabledrainpanunderthedipstick/oildrain.
7.Cleanaroundthedipstick.
8.Removethedipstickbyrotatingthecap
counterclockwiseandpullingitout.
9.Tipthemachineontoitsrightside(airlterup)to
draintheoilintothedrainpan.
10.Afterdrainingtheoil,returnthemachinetothe
operatingposition.
11.FillthecrankcasetotheFullmarkonthedipstickwith
freshoil;refertoChangingtheEngineOil(page17).
12.Insertthedipstickintothellerneckandrotatethecap
clockwiseuntilitistight.
13.Wipeupanyspilledoil.
14.Recycletheusedoilaccordingtolocalcodes.
ChangingtheEngine-OilFilter
ServiceInterval:Every200hours
1.Runtheenginetowarmtheoil.
WARNING
Oilmaybehotaftertheenginehasbeenrun,
andcontactwithhotoilcancausesevere
personalinjury.
Avoidcontactingthehotengineoilwhenyou
drainit.
17
2.Shutofftheengineandwaitforallmovingpartsto
stop.
3.Disconnectthewirefromthesparkplug.
4.Drainthegasolinefromthefueltank.
5.Draintheengineoil;refertoChangingtheEngineOil
(page17).
6.Placearagundertheoillter(Figure23)tocatchany
oilthatmayleakoutasyouremovetheoillter.
Figure23
1.Oillter
7.Removetheoillter.
8.Useyourngertocoatthegasketonthenewoillter
withoil(Figure26).
Figure24
1.Gasket
9.Installthenewlterbyrotatingitclockwiseuntilthe
sealcontactsthelterhousing,thenrotatethelteran
additional3/4turnbyhand.
10.FillthecrankcasetotheFulllineonthedipstickwith
freshoil;refertoChangingtheEngineOil(page17).
11.Connectthewiretothesparkplug.
12.Runtheengineforabout3minutes.
13.Shutofftheengine,waitforallmovingpartstostop,
andcheckforoilleakagearoundthelter.
14.Addoiltocompensatefortheoilintheoillter.Refer
toCheckingtheEngine-OilLevel(page11).
15.Recycletheusedoillterproperly.
ServicingtheSparkPlug
ServiceInterval:Every100hours—Inspect,clean,and
adjustthesparkpluggap;replacethe
sparkplugifnecessary.
UseanNGKBPR5ESsparkplugorequivalent.
1.Shutofftheengineandwaitforallmovingpartsto
stop.
2.Disconnectthewirefromthesparkplug.
3.Cleanaroundthesparkplug.
4.Removethesparkplugfromthecylinderhead.
Important:Replaceacracked,fouled,ordirty
sparkplug.Donotcleantheelectrodesbecause
gritenteringthecylindercandamagetheengine.
5.Setthegapontheplugto0.76mm(0.030inch);refer
toFigure25.
Figure25
1.Center-electrodeinsulator
2.Sideelectrode
3.Airgap(nottoscale)
6.Carefullyinstallthesparkplugbyhand(toavoidcross
threading)untilitishandtight.
7.Tightenthesparkplugto23N∙m(2.3kgf-m,17ft-lb).
Important:Aloosesparkplugcanbecomevery
hotandcandamagetheengine;overtighteninga
sparkplugmaydamagethethreadsinthecylinder
head.
8.Connectthewiretothesparkplug.
18
DriveSystem
Maintenance
AdjustingtheSelf-PropelDrive
Ifthemachineisnew,doesnotself-propel,orittendsto
creepforward,adjustthedrivecable.
1.Movethemachineoutsideandontoapavedsurface
nearasolidwalltosafelypreventthemachinefrom
movingforwardwhiletheengineisrunning.
2.Positionthemachinewiththefronttiresagainstthe
wall.
Note:Ensurethattheareaiswellventilatedandclear
ofdebristhatcouldbethrownbythemachine.
3.Shiftthetransmissiontothirdgear.
4.Starttheengine;refertoStartingtheEngine(page12).
5.Pulltheself-propel-drivebartothehandle.
Note:Thewheelsshouldstarttoturnasthe
self-propel-drivebarjusttouchesthehandle.
6.Shutofftheengine.
7.Ifyoumustadjustthemachine,dothefollowing:
•Ifthewheelsdonotspinwhenyouengagethe
self-propel-drivebar,thetractionbeltistooloose.
Rotatethewheel-drive-controlknob(Figure26)
clockwise1turnandrepeatsteps4through6.
Figure26
1.Wheel-drive-controlknob
•Ifthewheelsspinbeforeyoufullyengagethe
self-propel-drivebar,thetractionbeltistootight.
Rotatethewheel-drive-controlknob(Figure26)
counterclockwise1turnandrepeatsteps4through
6.
8.Foranewtractionbelt,rotatethedrivecable
adjustmentknobclockwise1additionalturntoallow
forthenormalstretchingofthebeltduringthebreak-in
period.
Note:Youcanskipthisstepifyouareadjustinga
usedbelt.
BrakeMaintenance
AdjustingtheBlade-Brake
Cable
Ifthebladebrakecableneedstobereplacedorisnotadjusted
properly,adjustthebladebrakecable.
1.Shutofftheengineandwaitforallmovingpartsto
stop.
2.Disconnectthewirefromthesparkplug.
3.Holdtheblade-controlbarat19cm(7-5/8inches)
fromthetopofthehandleasshowninFigure27.
Figure27
1.Handlebar3.Blade-controlbar
2.Cable-anchornut4.19cm(7-5/8inches)
4.Loosenthecable-anchornut.
5.Pulldownonthecableconduittoremovetheslack
fromthebrakecable.
6.Tightenthecable-anchornut.
7.Releasetheblade-controlbarandverifythereisslack
inthebrakecable.
19
BladeMaintenance
MaintainingtheBlade
Alwaysmowwithasharpblade.Asharpbladecutscleanly
andwithouttearingorshreddingthegrassblades.
1.Shutofftheengineandwaitforallmovingpartsto
stop.
2.Disconnectthewirefromthesparkplug.
3.Closethefuelvalvebymovingthefuel-valveleverto
theleft(Figure15).
4.Drainthegasolinefromthefueltank.
5.Tipthemachineontoitsrightside(aircleanerup)as
showninFigure28.
Figure28
1.Blade3.Bladeboltandlockwasher
2.Accelerator
InspectingtheBlade
ServiceInterval:Beforeeachuseordaily—Inspectthe
mowerbladesforwearordamage.
Carefullyexaminethebladeforsharpnessandwear,especially
wheretheatandthecurvedpartsmeet(Figure29A).
Becausesandandabrasivematerialcanwearawaythemetal
thatconnectstheatandcurvedpartsoftheblade,check
thebladebeforeusingthemachine.Ifyounoticeaslotor
wear(Figure29BandFigure29C),replacetheblade;referto
RemovingtheBlade(page21).
Figure29
1.Sail
3.Wear
2.Flatpartoftheblade4.Slotformed
Note:Forthebestperformance,installanewbladebefore
themowingseasonbegins.Duringtheyear,ledownany
smallnickstomaintainthecuttingedge.
DANGER
Awornordamagedbladecanbreak,andapieceof
thebladecouldbethrowntowardyouorbystanders,
resultinginseriouspersonalinjuryordeath.
•Inspectthebladeperiodicallyforwearor
damage.
•Replaceawornordamagedblade.
InspectingtheAccelerator
ServiceInterval:Beforeeachuseordaily—Inspectthe
acceleratorforwearordamage.
Carefullyexaminetheacceleratorforexcessivewear(Figure
30).Becausesandandabrasivematerialcanwearawaythe
metal(especiallyintheareashownasitem2inFigure30),
checktheacceleratorbeforeusingthemachine.Ifyounotice
thatatabontheacceleratorhasbeenworndowntoasharp
edgeorthereisacrack,replacetheaccelerator.
1 2
3
4
g027496
Figure30
1.Accelerator3.T ab
2.Weararea
4.Crackformed
20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Toro 21in Heavy-Duty Recycler/Rear Bagger Lawn Mower User manual

21in Heavy-Duty Recycler/Rear Bagger Lawn Mower
Toro
Brand
Toro
Model
21in Heavy-Duty Recycler/Rear Bagger Lawn Mower
Category
Lawnmowers
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents