Operator’s Manual
IMPORTANT: Read this manual carefully. It contains information about your
safety and the safety of others. Also become familiar with the controls and
their proper use before you operate the product.
FORM NO. 3321–966
Wheel
Horse
520Lxi Tractor
Model No. 73547 – 9900001 & UP
The Toro Company – 1999
All Rights Reserved
Introduction
Thank you for purchasing a Toro product.
All of us at Toro want you to be completely satisfied
with your new product, so feel free to contact your
local Authorized Service Dealer for help with service,
genuine replacement parts, or other information you
may require.
Whenever you contact your Authorized Service
Dealer or the factory, always know the model and
serial numbers of your product. These numbers will
help the Service Dealer or Service Representative
provide exact information about your specific
product. You will find the model and serial number
plate located in a unique place on the product as
shown below
.
1
m–2345
1. Model
and Serial Number Plate
For your convenience, write the product model and
serial numbers in the space below.
Model No.
Serial No.
Read this manual carefully to learn how to operate
and maintain your product correctly. Reading this
manual will help you and others avoid personal injury
and damage to the product. Although we design,
produce and market safe, state-of-the-art products,
you are responsible for using the product properly
and safely. You are also responsible for training
persons, you allow to use the product, about safe
operation.
The warning system in this manual identifies
potential hazards and has special safety messages that
help you and others avoid personal injury, even death.
DANGER, WARNING and CAUTION are signal
words used to identify the level of hazard. However,
regardless of the hazard, be extremely careful.
DANGER signals an extreme hazard that will cause
serious injury or death if the recommended
precautions are not followed.
WARNING signals a hazard that may cause serious
injury or death if the recommended precautions are
not followed.
CAUTION signals a hazard that may cause minor or
moderate injury if the recommended precautions are
not followed.
Two other words are also used to highlight
information. “Important” calls attention to special
mechanical information and “Note” emphasizes
general information worthy of special attention.
The left and right side of the machine is determined
by sitting on the seat in the normal operator’s
position.
The engine exhaust from this product
contains chemicals known to the State of
California to cause cancer, birth defects,
or other reproductive harm.
IMPORTANT: The engine in this product is
not equipped with a spark arrester muffler.
It is a violation of California Public Resource
Code Section 4442 to use or operate this
engine on any forest–covered, brush–covered
or grass–cover
ed land as defined in CPRC
4126. Other states or federal areas may have
similar laws.
1
Contents
Page
Slope Chart 5.
. . . . . . . . . . . . . . . . . . . . . . . .
Safety and Instruction Decals 7
. . . . . . . . . .
Check Before Operating 8
. . . . . . . . . . . . . . . . . .
Opening the Hood 8
. . . . . . . . . . . . . . . . . . .
Closing the Hood 9
. . . . . . . . . . . . . . . . . . . .
Removing the Side Panels 9
. . . . . . . . . . . . .
Adding Fuel 10
. . . . . . . . . . . . . . . . . . . . . . . .
Check the Engine Oil Level 11
. . . . . . . . . . . .
Check the Cooling System
12
. . . . . . . . . . . . .
Check for Debris 13
. . . . . . . . . . . . . . . . . . . .
Check the Safety Interlock System 14
. . . . . .
Check the Brake
14
. . . . . . . . . . . . . . . . . . . . .
Operation 15
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Think Safety First 15
. . . . . . . . . . . . . . . . . . .
Controls 15
. . . . . . . . . . . . . . . . . . . . . . . . . . .
“Key Choice” Key
15
. . . . . . . . . . . . . . . . . . .
Parking Brake 15
. . . . . . . . . . . . . . . . . . . . . . .
Starting and Stopping the Engine 16
. . . . . . .
Operating the Power Take Off (PTO) 17
. . . .
The Safety Interlock System 17
. . . . . . . . . . .
Operating–in–Reverse 17
. . . . . . . . . . . . . . . .
Gauges and Indicator Lights 20
. . . . . . . . . . .
Driving Forward or Backward 21
. . . . . . . . . .
Stopping the Machine 22
. . . . . . . . . . . . . . . .
Re–centering the Steering Wheel 22
. . . . . . . .
Attachment Power Lift 23
. . . . . . . . . . . . . . . .
Positioning the Seat 23
. . . . . . . . . . . . . . . . . .
Page
Headlights and Taillights 24
. . . . . . . . . . . . . .
Positioning the Tilt Steering Wheel 24
. . . . . .
Using the Cruise Control 24
. . . . . . . . . . . . . .
The Smart Turn Steering Feature 25
. . . . . .
Pushing the Machine by Hand 25
. . . . . . . . . .
Maintenance 26
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Interval Chart 26
. . . . . . . . . . . . . . . .
Air Cleaner 27
. . . . . . . . . . . . . . . . . . . . . . . . .
Engine Oil 29
. . . . . . . . . . . . . . . . . . . . . . . . .
Changing the Engine Coolant 31
. . . . . . . . . .
Spark Plugs 31
. . . . . . . . . . . . . . . . . . . . . . . .
Greasing and Lubrication 33
. . . . . . . . . . . . . .
Tire Pressure 34
. . . . . . . . . . . . . . . . . . . . . . . .
Brake 35
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Tank 36
. . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Filter 37
. . . . . . . . . . . . . . . . . . . . . . . . . .
Front Wheel Toe-In 38
. . . . . . . . . . . . . . . . . .
Transaxle Fluid 39
. . . . . . . . . . . . . . . . . . . . . .
Fuse 41
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights 41
. . . . . . . . . . . . . . . . . . . . . . . . .
Taillights 42
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery 43
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Diagram 46
. . . . . . . . . . . . . . . . . . . . .
Wiring Diagram 47
. . . . . . . . . . . . . . . . . . . . .
Cleaning and Storage 48
. . . . . . . . . . . . . . . . .
Troubleshooting 49
. . . . . . . . . . . . . . . . . . . . . . . . .
! % ! # ! !# "
$ " "" &
" !! " #" !! !&!"!
" % "&
"! % ! # %" &# #" # "!
% ! #
"& "! & " # "
#"#
2
Safety
This machine meets or exceeds the B71.1–1996
specifications of the American National Standards
Institute, in effect at the time of production.
However, improper use or maintenance by the
operator or owner can result in injury. To reduce
the potential for injury, comply with these safety
instructions and always pay attention to the safety
alert
symbol, which means CAUTION,
WARNING, or DANGER—“personal safety
instruction.” Failure to comply with the
instruction may result in personal injury or death.
Safe
Operating Practices
This product is capable of amputating hands and feet
and throwing objects. Always follow all safety
instructions to avoid serious injury or death.
POTENTIAL HAZARD
• Engine exhaust contains carbon monoxide,
which is an odorless, deadly poison.
WHAT CAN HAPPEN
• Carbon monoxide can kill you and is also
known to the State of California to cause
birth defects.
HOW TO AV
OID THE HAZARD
• Do not run engine indoors or in an enclosed
area.
General Operation
1. Read, understand, and follow all instructions in
the operator’s manual and on the machine before
starting.
2. Allow only responsible adults who are familiar
with the instructions to operate the machine.
3. Clear the area of objects such as rocks, toys,
wire, etc., which could be picked up and thrown
by the blade.
4. Be sure the area is clear of other people before
mowing. Stop the machine if anyone enters the
area.
5. Never carry passengers.
6. Do not mow in reverse unless absolutely
necessary. Always look down and behind before
and while backing.
7. Be aware of the mower discharge direction and
do not point it at anyone. Do not operate the
mower without either the entire grass catcher or
the guard in place.
8. Slow down before turning. Sharp turns on any
terrain may cause loss of control.
9. Never leave a running machine unattended.
Always turn off blades, set parking brake, stop
engine, and remove keys before dismounting.
10. Remove both the “ignition” and “Key Choice”
keys and put them in a safe place, out of the
reach of children, when not using the machine.
11. Turn off blades when not mowing.
12. Keep hands, feet, hair and loose clothing away
from attachment discharge area, underside of
mower and any moving parts while engine is
running.
13. Stop the engine before removing the grass
catcher or unclogging the chute.
14. Mow only in daylight or good artificial light.
15. Do not operate the machine while under the
influence of alcohol or drugs.
16. Watch for traffic when operating near or crossing
roadways.
Safety
3
17. Use extra care when loading or unloading the
machine into a trailer or truck.
18. Do not touch equipment or attachment parts
which may be hot from operation. Allow to cool
before attempting to maintain, adjust or service.
Slope Operation
Slopes are a major factor related to loss-of-control
and tip-over accidents, which can result in severe
injury or death. All slopes require extra caution. If
you cannot back up the slope or if you feel uneasy on
it, do not mow it.
DO
• Mow up and down slopes greater than 5°, not
across.
• Mow downhill only on slopes above 10°, never
mow uphill. If a steep slope must be ascended,
back up the hill, and drive forward down the hill,
keeping the machine in gear.
• Remove obstacles such as rocks, tree limbs, etc.
from the mowing area. Watch for holes, ruts or
bumps, as uneven terrain could overturn the
machine. T
all grass can hide obstacles.
• Use slow speed. Choose a low gear so that you
will not have to stop or shift while on the slope.
• Follow the manufacturer’s recommendations for
wheel weight or counterweights to improve
stability.
• Use extra care with grass catchers or other
attachments. These can change the stability of
the machine.
• Keep all movement on slopes slow and gradual.
Do not make sudden changes in speed or
direction.
• Avoid starting or stopping on a slope. If tires
lose traction, disengage the blades and proceed
slowly straight down the slope.
DO NOT
• Do not operate machine on hillsides or slopes
exceeding 15
°.
• Avoid turning on slopes. If you must turn, turn
slowly and gradually downhill, if possible.
• Do not mow near drop-offs, ditches, or
embankments. The machine could suddenly turn
over if a wheel goes over the edge of a cliff or
ditch, or if an edge caves in.
• Do not mow on wet grass. Reduced traction
could cause sliding.
• Do not try to stabilize the machine by putting
your foot on the ground.
• Do not use a grass catcher on steep slopes.
Heavy grass bags could cause loss of control or
overturn the machine.
Safety
4
Children
Tragic accidents can occur if the operator is not alert
to the presence of children. Children are often
attracted to the machine and the mowing activity.
Never assume that children will remain where you
last saw them. The following requirements must be
followed to prevent injury to children.
1. Keep children out of the mowing area and under
the watchful care of another responsible adult.
2. Be alert and turn the machine off if children
enter the area.
3. Before and while backing, look behind and down
for small children.
4. Never carry children. They may fall off and be
seriously injured or interfere with safe machine
operation.
5. Never allow children to operate the machine.
6. Use extra care when approaching blind corners,
shrubs, trees, the end of a fence or other objects
that may obscure vision.
Service
1. Stop the engine and disconnect spark plug
wire(s) before performing any service, repairs,
maintenance or adjustments.
2. Use extra care when handling gasoline and other
fuels. They are flammable and vapors are
explosive.
A. Use only an approved container.
B. Never remove the gas cap or add fuel when
the engine is running. Allow the engine to
cool before refueling. Do not smoke.
C. Never refuel the machine indoors.
D. Never store the machine or fuel container
inside where there is an open flame, such as
near a water heater or furnace.
3. Never run a machine inside a closed area.
4. Keep nuts and bolts tight, especially the blade
attachment bolts. Keep equipment in good
condition.
5. Never tamper with safety devices. Check safety
systems for proper operation before each use.
6. Keep the machine free of grass, leaves, or other
debris build-up. Clean up oil or fuel spillage.
Allow the machine to cool before storing.
7. Stop and inspect the equipment if you strike an
object. Repair, if necessary, before restarting.
8. Grass catcher components are subject to wear,
damage and deterioration, which could expose
moving parts or allow objects to be thrown.
Frequently check components and replace with
manufacturer’s recommended parts, when
necessary.
9. Mower blades are sharp and can cut. Wrap the
blade(s) or wear gloves, and use extra caution
when servicing them.
10. Use only genuine Toro replacement parts to
ensure that original standards are maintained.
11. Check brake operation frequently. Adjust and
service as required.
12. Battery acid is poisonous and can cause burns.
Avoid contact with skin, eyes and clothing.
Protect your face, eyes and clothing when
working with a battery.
13. Battery gases can explode. Keep cigarettes,
sparks and flames away from battery.
Safety
5
Slope
Chart
Read all safety instructions on pages 2–4.
6
Safety
7
Safety
and Instruction Decals
Safety decals and instructions are easily visible to the operator and are located near
any area of potential danger. Replace any decal that is damaged or lost.
ON DRIVE SHAFT TUNNEL
(Part No. 80–8760)
ON RADIA
T
OR F
AN
SHROUD
(Part No.95–4143)
(2) UNDER SIDE SHIELD
(Part No. 98–5014)
ON BA
TTER
Y STRAP
(Part No. 93–1265)
ON DRIVE SHAFT COVER
(Part No. 99–6090)
ON FRONT OF SEA
T
BRACKET
(Part No. 99–5339
ON FRONT OF SEA
T
BRACKET
(Part No. 99–2985
8
Check
Before Operating
Each time before operating your tractor, check the
following:
• Fuel level
• Engine oil level
• Cooling system fluid level and radiator screen
• Debris on the (3) air intake screens
• Debris in the engine area
• Debris on the rear transaxle cover
• The safety interlock system
• The brake
Some of these steps will require that you open the
hood or remove the side panels on the tractor.
Opening
the Hood
To open the hood:
1. Park the machine on a level surface, disengage
the power take off (PTO), set the parking brake,
lower the attachment lift, and turn the ignition
key to “STOP” to stop the engine. Remove the
ignition key.
2. Push the hood latch (Fig. 1), located just above
the indicator light panel, to the left.
3. Raise the hood to full height.
m–3314
1
Figure 1
1. Hood
latch
POTENTIAL
HAZARD
• Components under the hood will be hot if
the tractor has been running.
WHAT CAN HAPPEN
• Touching hot components can cause burns.
HOW TO AV
OID THE HAZARD
• Allow the tractor to cool before performing
maintenance or touching components
under the hood.
Check Before Operating
9
Closing
the Hood
The hood catch is located at the left hand corner of
the grille.
1. Press rearward on the hood catch as you begin to
lower the hood.
2. Push the hood down until the latch closes.
1
2
2
Front of tractor
Figure 2
1. Hood
catch
2.
Hood hinges
Removing
the Side Panels
1. Park the machine on a level surface, disengage
the power take off (PTO), set the parking brake,
lower the attachment lift, and turn the ignition
key to “STOP” to stop the engine. Remove the
ignition key.
2. To remove a side panel:
A. Lift up and twist each of the two side panel
latches 90
, or until they line up with the
open slot (Fig. 3).
B. Pull the top of the side panel toward you
until the side panel latches pass through the
open slot.
C. Lift the side panel from the tractor.
m–3318
1
2
Figure 3
1. Side
panel latch
2.
Open slot
POTENTIAL
HAZARD
• Rotating fan and drive shaft can cause
injury.
WHAT CAN HAPPEN
• Fingers, hands or loose clothing can get
caught by rotating fan and drive shaft.
HOW TO AV
OID THE HAZARD
• Do not operate the tractor without the side
panels and hood in place.
• Keep fingers, hands and clothing clear of
rotating fan and drive shaft.
• Shut off the engine and remove the ignition
key before performing maintenance.
Check Before Operating
10
Adding
Fuel
Use UNLEADED Regular Gasoline suitable for
automotive use (85 pump octane minimum). Leaded
regular gasoline may be used if unleaded regular is
not available.
IMPORTANT: Never use methanol, gasoline
containing methanol, or gasohol containing
more than 10% ethanol because the fuel
system could be damaged. Do not mix oil with
gasoline.
POTENTIAL HAZARD
• In certain conditions gasoline is extremely
flammable and highly explosive.
WHAT CAN HAPPEN
• A fire or explosion from gasoline can burn
you, others, and cause property damage.
HOW TO AV
OID THE HAZARD
• Use a funnel and fill the fuel tank outdoors,
in an open area, when the engine is cold.
Wipe up any gasoline that spills.
• Do not fill the fuel tank completely full.
Add gasoline to the fuel tank until the level
is 1/4” to 1/2” (6 mm to 13 mm) below the
bottom of the filler neck. This empty space
in the tank allows gasoline to expand.
• Never smoke when handling gasoline, and
stay away from an open flame or where
gasoline fumes may be ignited by a spark.
• Store gasoline in an approved container
and keep it out of the reach of children.
Never buy more than a 30-day supply of
gasoline.
IMPORTANT: Never use fuel additives
containing methanol or ethanol.
POTENTIAL HAZARD
• When fueling, under certain circumstances,
a static charge can develop, igniting the
gasoline.
WHAT CAN HAPPEN
• A fire or explosion from gasoline can burn
you and others and cause property damage.
HOW TO AV
OID THE HAZARD
• Always place gasoline containers on the
ground away from your vehicle before
filling.
• Do not fill gasoline containers inside a
vehicle or on a truck or trailer bed because
interior carpets or plastic truck bed liners
may insulate the container and slow the
loss of any static charge.
• When practical, r
emove gas–power
ed
equipment from the truck or trailer and
refuel the equipment with its wheels on the
ground.
• If this is not possible, then refuel such
equipment on a truck or trailer from a
portable container, rather than from a
gasoline dispenser nozzle.
• If a gasoline dispenser nozzle must be used,
keep the nozzle in contact with the rim of
the fuel tank or container opening at all
times until fueling is complete.
Filling the Fuel Tank
1. Park the machine on a level surface, disengage
the power take off (PTO), set the parking brake,
lower the attachment lift, and turn the ignition
key to “STOP” to stop the engine. Remove the
ignition key.
Check Before Operating
11
2. Clean around the fuel tank cap and remove the
cap. Use a funnel and add fuel until the fuel
level is 1/4 to 1/2 inch (6 mm to 13 mm) below
the bottom of the filler neck. This space in the
tank allows for expansion of the fuel. When
filling the tank, make sure that the machine is on
a level surface so that adequate air space is
allowed. Do not fill the fuel tank completely.
3. Install the fuel tank cap securely. Wipe up any
gasoline that may have spilled.
Check
the Engine Oil Level
1. Park the machine on a level surface, disengage
the power take off (PTO), set the parking brake,
lower the attachment lift, and turn the ignition
key to “STOP” to stop the engine. Remove the
ignition key.
2. Open the hood.
3. Clean around the oil dipstick (Fig. 4) so dirt
cannot fall into the dipstick hole and damage the
engine.
4. Pull out the oil dipstick and wipe the metal end
clean (Fig. 5).
5. Slide the oil dipstick fully into the tube. Pull the
dipstick out and look at the metal end. If the oil
level is near or below the “L” mark on the
dipstick, remove the filler cap and add oil only
to the “H” mark on the dipstick. (Refer to
Engine Oil, page 29, for the correct oil type and
viscosity to use in different temperature
conditions).
IMPORTANT: Do not overfill the crankcase
with oil because this may result in engine
damage.
1
2
m–3423
Figure 4
1. Dipstick 2. Filler
Cap
m–3219
1
Figure
5
1. Metal
end
Check Before Operating
12
Check
the Cooling System
Check Radiator Coolant
The cooling system is filled with a 50/50 solution of
water and permanent ethylene glycol anti–freeze.
Check the level of coolant at the beginning of each
day before starting the engine.
POTENTIAL HAZARD
• Coolant is hot and pressurized.
WHAT CAN HAPPEN
• Discharge of hot pressurized coolant can
cause sever
e burns.
HOW TO AV
OID THE HAZARD
• Do not remove the radiator cap to check
coolant. Follow the directions below for
checking coolant.
• Do not remove the radiator cap when the
engine is hot. Always allow the engine to
cool at least 15 minutes or until the
radiator cap is cool enough to touch
without burning your hand before
removing the radiator cap.
1. Park the machine on a level surface, disengage
the power take off (PTO), set the parking brake,
lower the attachment lift, and turn the ignition
key to “STOP” to stop the engine. Remove the
ignition key.
2. Open the hood.
3. Check coolant level. Coolant should be between
the two lines on the reserve tank when the
engine is cold (Fig. 6).
1
2
3
4
m–3423
Figure 6
1. Reserve
tank cap
2.
Reserve tank
3.
Maximum level line (cold)
4.
Minimum level line (cold)
4. If coolant is low, remove the reserve tank cap
and add a 50/50 mixture of water and permanent
ethylene glycol anti–freeze. DO NOT
OVERFILL.
5. Install the reserve tank cap.
Check Before Operating
13
Check
for Debris
IMPORTANT: Operating the engine with a
blocked grass scr
een and/or cooling shrouds
removed, will result in engine damage from
overheating.
1. Park the machine on a level surface, disengage
the power take off (PTO), set the parking brake,
lower the attachment lift, and turn the ignition
key to “STOP” to stop the engine. Remove the
ignition key.
2. Check for debris on the (3) air intake screens
(Fig. 7). Wipe away debris before each use
and/or during use, if required.
1
m–3412
1
Figure 7
Arrows show air intake and exhaust path
1. Air
intake screens (1 of 3
shown)
3. The radiator screen (Fig. 8) is located between
the radiator and the dash in the tractor. To
remove it, pull it up from its retention slot.
Wipe or wash off all accumulated debris from
the screen, then reinstall it.
4. In dry or dusty conditions, dust can build up on
the radiator fins and reduce cooling efficiency.
Remove the radiator screen and blow (or low
pressure wash) the radiator cooling fins.
1
m–3424
Figure 8
1. Radiator
screen
5. Debris can build up in the engine area. Clean
any debris build–up with a brush or blower
before each use.
IMPORTANT: It is preferable to blow dirt
out (Fig. 9), rather than washing it out. If
water is used, keep it away from electrical
items.
m–3615
Figure 9
IMPORTANT: DO NOT HIGH–PRESSURE
WASH. High–pressure washing can damage
the electrical system or deplete grease.
Check Before Operating
14
6. The rear transaxle cover is an air intake area for
cooling the transaxle. Clean debris from the rear
transaxle cover before operating the tractor
(Fig. 10).
1
m–3436
Figure 10
1. Rear
transaxle cover
Check
the Safety Interlock
System
Always check the interlock system before operating
the tractor. Instructions for checking the interlock
system are found in the Operation section, page 15.
Check
the Brake
Refer to Checking and Adjusting the Brake, page 35.
15
Operation
Think
Safety First
Please carefully read all the safety instructions on
pages 2–7. Knowing this information could help you,
your family, pets or bystanders avoid injury.
Controls
Become familiar with all the controls (Fig. 11) before
you start the engine and operate the machine.
m–3597
4
1
2
7
3
8
5
6
9
10
11
12
13
14
15
16
Figure 1
1
1. Throttle
2. Choke
3. PTO
switch
4.
Seat adjustment lever
5.
Engine water temperature
gauge
6.
Attachment lift lever
7.
Indicator lights
8.
Fuel gauge
9.
Hour meter
10.
Ignition switch
11.
Brake pedal
12.
Parking brake lever
13.
High–Low range lever
14.
Cruise control switch
15.
Steering wheel tilt lever
16. T
raction control pedal
“Key
Choice” Key
A turn and release key used for deactivating the
“Operating–In–Reverse” interlock feature. Located
on the seat bracket in front of and just below the seat
(Fig. 12).
m–4260
1
Figure 12
1. “Key
Choice“ Key
Parking Brake
Always set the parking brake when you stop the
machine or leave it unattended.
Setting the Parking Brake
1. Push the brake pedal (Fig. 11) down and hold it
in the depressed position.
2. Lift the parking brake lever (Fig. 11) up and
gradually take your foot off the brake pedal. The
brake pedal should stay in the depressed (locked)
position.
Operation
16
Releasing the Parking Brake
1. Push down on the brake pedal (Fig. 11). The
parking brake lever should release.
2. Release the brake pedal.
Starting
and Stopping
the Engine
Starting
1. Sit down on the seat.
2. Depress the brake pedal.
Note: The engine will not start unless you
fully depress the brake pedal.
3. Push the PTO (power take off) switch to OFF
(Fig. 13).
4. Move the choke lever to ON (if the engine is
cold) (Fig. 13).
5. Move the throttle lever halfway to FAST
(Fig. 13).
6. Turn the ignition key clockwise and hold it in
the START position (Fig. 14). When the engine
starts, release the key.
IMPORTANT: Do not run the starter motor
more than 5 seconds at a time or premature
starter failure may result. If the engine fails to
start after 5 seconds, turn the key to the OFF
position, recheck the controls and procedures,
wait 10 additional seconds and repeat the
starting operation; refer to Troubleshooting,
page 49.
7. After the engine starts, gradually move the choke
lever to OFF (Fig. 13). If the engine stalls or
hesitates, move the choke lever back to ON for a
few seconds. Then move the throttle lever to the
desired setting.
Note: Allowing the engine to warm up before
putting it under load will lengthen
engine life.
m–3257
1
2
3
Figure 13
1. Throttle
2. Choke
3. PTO
switch
m–3312
1
2
3
4
Figure
14
1. Stop
2. Run
with lights
3. Run
4. Start
Stopping
1. Move the throttle lever to SLOW (Fig. 13).
2. Allow the engine to run for a short time to cool
down.
3. Turn the ignition key to “STOP” (Fig. 14).
4. Always remove both the ignition and “Key
Choice” keys when the equipment is not in use
or unattended.
Operation
17
Operating
the
Power T
ake Off (PT
O)
The power take–off (PTO) switch engages and
disengages power to the electric clutch.
If the ignition key is in the RUN or LIGHTS position
and the power take off (PTO) is engaged, the PTO
indicator light will be on. When this light is on, it is a
reminder: the implement is being powered and the
starter will not crank while the PTO is engaged.
Always turn off the PTO before getting off the seat.
Engaging the Power Take Off (PTO)
1. Depress the brake pedal to stop the machine.
2. Move the throttle lever to FAST.
IMPORTANT: For best performance, always
use full throttle when the power take off
(PTO) switch is ON.
3. Pull the power take off (PTO) switch to ON
(Fig. 15).
m–3264
1
2
Figure 15
1. Push
(of
f-disengaged) 2.
Pull (on-engaged)
Disengaging the Power Take Off (PTO)
1. Push the power take off (PTO) switch to OFF.
The
Safety Interlock System
Understanding the Safety Interlock
System
The safety interlock system is designed to prevent the
engine from starting unless:
• You are sitting on the seat
• The brake pedal is depressed
• The power take off (PTO) is OFF
The safety interlock system is designed to stop the
engine if:
• You rise from the seat when the brake pedal is
released
• You rise from the seat when the power take off
(PTO) is “ON”.
The safety interlock system is designed to stop the
power take off (PTO) if:
• You shift into reverse with the power take off
(PTO) engaged.
Operating–in–Reverse
An interlock feature is provided that prevents the
Power Take Off (PTO) from operating while the
tractor is traveling in reverse. If the unit is shifted into
reverse while the mower blade or other PTO driven
attachment is engaged, the PTO will stop.
If you need to mow while in reverse gear or use other
PTO driven attachments (such as a snowthrower or
tiller), this operating–in–reverse interlock feature may
be temporarily deactivated. Do not mow while
backing up unless it is absolutely necessary.
Operation
18
Before deactivating this feature, be sure there are no
children present on or near the property where you are
using the tractor, and that none are likely to appear
while you are mowing or operating an attachment. Be
extra observant after you have chosen to deactivate
the interlock feature because the sound of the tractor’s
engine might prevent you from being aware that a
child or a bystander has entered the area where you
are operating the tractor.
If you are certain that you can safely mow in reverse
or operate an attachment, deactivate the
operating–in–reverse interlock feature by turning the
“Key Choice” key (Fig. 16), located on the seat
bracket in front of and just below the seat, after
engaging the blade (PTO). A red light on the front
console (Fig. 17) will turn on as a reminder that the
operating–in–reverse interlock has been deactivated.
Once the interlock is deactivated it stays in this
mode––with your mower blade or PTO–driven
attachment operating whenever you back up–– and
the console light stays on until either the blade (PTO)
is disengaged, or the engine is turned off.
Note: Do not insert the “Key Choice” key
unless it is absolutely necessary to
mow in reverse or operate an
attachment. The “Key Choice” key
should also be removed from the unit
if it will be operated by someone other
than a responsible, experienced
operator. This will prevent the PTO
from operating when the tractor is
moving in reverse. Always remove
both the ignition and the “Key Choice”
keys and put them in a safe place out
of the reach of children when leaving
the unit unattended.
POTENTIAL HAZARD
• A child or bystander could be backed over
by a riding mower with its blade(s)
engaged.
WHAT CAN HAPPEN
• Blade contact will cause serious personal
injury or death.
HOW TO AV
OID THE HAZARD
• Do not mow in r
everse unless absolutely
necessary.
• Always look backward and down before
backing up.
• Use “Key Choice” key only if you are
certain no children or other bystanders will
appear in the mowing area.
•
Always r
emove both the ignition and “Key
Choice” keys and put them in a safe place
out of the reach of children or unauthorized
users when leaving the unit unattended.
m–4260
1
Figure 16
1. “Key
Choice” key
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
