New Holland LS55-19H User manual
- Category
- Lawnmowers
- Type
- User manual
This manual is also suitable for
Publication
s N
umber
: 4
264651
0
9/97
NEW HOLLAND
LS55–19H
Yard Tractor
Model No
.
715695001 – T7E0001 & Up
OPERATOR’S
MANUAL
Introduction
Thank you for purchasing a New Holland product.
All of us at New Holland want you to be completely
satisfied with your new product, so feel free to
contact your local Authorized Service Dealer for help
with service, genuine replacement parts, or other
information you may require.
Whenever you contact your Authorized Service
Dealer or the factory, always know the model and
serial numbers of your product. These numbers will
help the Service Dealer or Service Representative
provide exact information about your specific
product. You will find the model and serial number
plate located in a unique place on the product as
shown below
.
1
1202a
1. Model
and Serial Number Plate
(under the seat)
For your convenience, write the product model and
serial numbers in the space below.
Read this manual carefully to learn how to operate
and maintain your product correctly. Reading this
manual will help you and others avoid personal injury
and damage to the product. Although we design,
produce and market safe, state-of-the-art products,
you are responsible for using the product properly
and safely. You are also responsible for training
persons, who you allow to use the product, about safe
operation.
The warning system in this manual identifies
potential hazards and has special safety messages that
help you and others avoid personal injury, even death.
DANGER, WARNING and CAUTION are signal
words used to identify the level of hazard. However,
regardless of the hazard, be extremely careful.
DANGER signals an extreme hazard that will cause
serious injury or death if the recommended
precautions are not followed.
WARNING signals a hazard that may cause serious
injury or death if the recommended precautions are
not followed.
CAUTION signals a hazard that may cause minor or
moderate injury if the recommended precautions are
not followed.
Two other words are also used to highlight
information. “Important” calls attention to special
mechanical information and “Note” emphasizes
general information worthy of special attention.
The left and right side of the machine is determined
by sitting on the seat in the normal operator’s
position.
The engine exhaust from this product
contains chemicals known to the State of
California to cause cancer, birth defects,
or other reproductive harm.
1
Contents
Page
Safety 2.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safe Operating Practices 2
. . . . . . . . . . . . . .
Slope Chart 5
. . . . . . . . . . . . . . . . . . . . . . . . .
Safety and Instruction Decals 7
. . . . . . . . . .
Gasoline and Oil 8
. . . . . . . . . . . . . . . . . . . . . . . .
Recommended Gasoline
8
. . . . . . . . . . . . . .
Filling the Fuel Tank 8
. . . . . . . . . . . . . . . . .
Check Engine Oil Level 8
. . . . . . . . . . . . . . .
Operation 9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Think Safety First 9
. . . . . . . . . . . . . . . . . . .
Controls 9
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking Brake 9
. . . . . . . . . . . . . . . . . . . . . . .
Starting and Stopping the Engine 10
. . . . . . .
Operating the Power Take Off (PTO) 11
. . . .
The Safety Interlock System 11
. . . . . . . . . . .
Indicator Control Module 12
. . . . . . . . . . . . .
Hourmeter 12
. . . . . . . . . . . . . . . . . . . . . . . . .
Driving Forward or Backward 13
. . . . . . . . . .
Stopping the Machine 13
. . . . . . . . . . . . . . . .
Attachment Power Lift 14
. . . . . . . . . . . . . . . .
Adjusting Dial-A-Height 14
. . . . . . . . . . . . . .
Positioning the Seat 15
. . . . . . . . . . . . . . . . . .
Headlights 15
. . . . . . . . . . . . . . . . . . . . . . . . .
Positioning the Tilt Steering Wheel 15
. . . . . .
Using the Cruise Control 16
. . . . . . . . . . . . . .
Pushing the Machine by Hand 16
. . . . . . . . . .
Page
Maintenance 17
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Interval Chart 17
. . . . . . . . . . . . . . . .
Air Cleaner 18
. . . . . . . . . . . . . . . . . . . . . . . . .
Engine Oil 20
. . . . . . . . . . . . . . . . . . . . . . . . .
Spark Plug 22
. . . . . . . . . . . . . . . . . . . . . . . . .
Greasing and Lubrication 23
. . . . . . . . . . . . . .
Tire Pressure 24
. . . . . . . . . . . . . . . . . . . . . . . .
Brake 25
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Tank 26
. . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Filter 27
. . . . . . . . . . . . . . . . . . . . . . . . . .
Power Lift 27
. . . . . . . . . . . . . . . . . . . . . . . . .
Front Wheel Toe-In 28
. . . . . . . . . . . . . . . . . .
Transaxle Fluid 29
. . . . . . . . . . . . . . . . . . . . . .
Fuse 29
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights 30
. . . . . . . . . . . . . . . . . . . . . . . . .
Battery 31
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Diagram 34
. . . . . . . . . . . . . . . . . . . . .
Cleaning and Storage 35
. . . . . . . . . . . . . . . . .
Troubleshooting 36
. . . . . . . . . . . . . . . . . . . . . . . . .
Warranty
Back Page
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Owner Assistance
Inside Back Cover
. . . . . . . . . . . . .
2
Safety
This machine meets or exceeds the B71.1–1990
specifications of the American National Standards
Institute, in effect at the time of production.
However, improper use or maintenance by the
operator or owner can result in injury. To reduce
the potential for injury, comply with these safety
instructions and always pay attention to the safety
alert
symbol, which means CAUTION,
WARNING, or DANGER—“personal safety
instruction.” Failure to comply with the
instruction may result in personal injury or death.
Safe
Operating Practices
This product is capable of amputating hands and feet
and throwing objects. Always follow all safety
instructions to avoid serious injury or death.
POTENTIAL HAZARD
• Engine exhaust contains carbon monoxide,
which is an odorless, deadly poison.
WHAT CAN HAPPEN
• Carbon monoxide can kill you and is also
known to the State of California to cause
birth defects.
HOW TO AV
OID THE HAZARD
• Do not run engine indoors or in an enclosed
area.
General Operation
1. Read, understand, and follow all instructions in
the operator’s manual and on the machine before
starting.
2. Allow only responsible adults who are familiar
with the instructions to operate the machine.
3. Clear the area of objects such as rocks, toys,
wire, etc., which could be picked up and thrown
by the blade.
4. Be sure the area is clear of other people before
mowing. Stop the machine if anyone enters the
area.
5. Never carry passengers.
6. Do not mow in reverse unless absolutely
necessary. Always look down and behind before
and while backing.
7. Be aware of the mower discharge direction and
do not point it at anyone. Do not operate the
mower without either the entire grass catcher or
the guard in place.
8. Slow down before turning. Sharp turns on any
terrain may cause loss of control.
9. Never leave a running machine unattended.
Always turn off blades, set parking brake, stop
engine, and remove key before dismounting.
10. Turn off blades when not mowing.
11. Keep hands, feet, hair and loose clothing away
from attachment discharge area, underside of
mower and any moving parts while engine is
running.
12. Stop the engine before removing the grass
catcher or unclogging the chute.
Safety
3
13. Mow only in daylight or good artificial light.
14. Do not operate the machine while under the
influence of alcohol or drugs.
15. Watch for traffic when operating near or crossing
roadways.
16. Use extra care when loading or unloading the
machine onto a trailer or truck.
17. Do not touch equipment or attachment parts
which may be hot from operation. Allow to cool
before attempting to maintain, adjust or service.
Slope Operation
Slopes are a major factor related to loss-of-control
and tip-over accidents, which can result in severe
injury or death. All slopes require extra caution. If
you cannot back up the slope or if you feel uneasy on
it, do not mow it.
DO
• Mow up and down slopes greater than 5°, not
across.
• Mow downhill only on slopes above 10°, never
mow uphill. If a steep slope must be ascended,
back up the hill, and drive forward down the hill,
keeping the machine in gear.
• Remove obstacles such as rocks, tree limbs, etc.
from the mowing area. Watch for holes, ruts or
bumps, as uneven terrain could overturn the
machine. T
all grass can hide obstacles.
• Use slow speed. Choose a low gear so that you
will not have to stop or shift while on the slope.
• Follow the manufacturer’s recommendations for
wheel weight or counterweights to improve
stability.
• Use extra care with grass catchers or other
attachments. These can change the stability of
the machine.
• Keep all movement on slopes slow and gradual.
Do not make sudden changes in speed or
direction.
• Avoid starting or stopping on a slope. If tires
lose traction, disengage the blades and proceed
slowly straight down the slope.
DO NOT
• Do not operate machine on hillsides or slopes
exceeding 15
°.
• Avoid turning on slopes. If you must turn, turn
slowly and gradually downhill, if possible.
• Do not mow near drop-offs, ditches, or
embankments. The machine could suddenly turn
over if a wheel goes over the edge of a cliff or
ditch, or if an edge caves in.
• Do not mow on wet grass. Reduced traction
could cause sliding.
• Do not try to stabilize the machine by putting
your foot on the ground.
• Do not use a grass catcher on steep slopes.
Heavy grass bags could cause loss of control or
overturn the machine.
Safety
4
Children
Tragic accidents can occur if the operator is not alert
to the presence of children. Children are often
attracted to the machine and the mowing activity.
Never assume that children will remain where you
last saw them. The following requirements must be
followed to prevent injury to children.
1. Keep children out of the mowing area and under
the watchful care of another responsible adult.
2. Be alert and turn the machine off if children
enter the area.
3. Before and while backing, look behind and down
for small children.
4. Never carry children. They may fall off and be
seriously injured or interfere with safe machine
operation.
5. Never allow children to operate the machine.
6. Use extra care when approaching blind corners,
shrubs, trees, the end of a fence or other objects
that may obscure vision.
Service
1. Stop the engine, disconnect spark plug wire(s)
and remove key before performing any service,
repairs, maintenance or adjustments.
2. Use extra care when handling gasoline and other
fuels. They are flammable and vapors are
explosive.
A. Use only an approved container.
B. Never remove the gas cap or add fuel when
the engine is running. Allow the engine to
cool before refueling. Do not smoke.
C. Never refuel the machine indoors.
D. Never store the machine or fuel container
inside where there is an open flame, such as
near a water heater or furnace.
3. Never run a machine inside a closed area.
4. Keep nuts and bolts tight, especially the blade
attachment bolts. Keep equipment in good
condition.
5. Never tamper with safety devices. Check safety
systems for proper operation before each use.
6. Keep the machine free of grass, leaves, or other
debris build-up. Clean up oil or fuel spillage.
Allow the machine to cool before storing.
7. Stop and inspect the equipment if you strike an
object. Repair, if necessary, before restarting.
8. Grass catcher components are subject to wear,
damage and deterioration, which could expose
moving parts or allow objects to be thrown.
Frequently check components and replace with
manufacturer’s recommended parts, when
necessary.
9. Mower blades are sharp and can cut. Wrap the
blade(s) or wear gloves, and use extra caution
when servicing them.
10. Use only genuine replacement parts to ensure
that original standards are maintained.
11. Check brake operation frequently. Adjust and
service as required.
12. Battery acid is poisonous and can cause burns.
Avoid contact with skin, eyes and clothing.
Protect your face, eyes and clothing when
working with a battery.
13. Battery gases can explode. Keep cigarettes,
sparks and flames away from battery.
Safety
5
Slope
Chart
Read all safety instructions on pages 2–4.
6
Safety
7
Safety
and Instruction Decals
Safety decals and instructions are easily visible to the operator and are located near
any area of potential danger. Replace any decal that is damaged or lost.
ON STEERING T
OWER
(Part No. TR93D0302)
ON FRAME
RIGHT REAR
(Part No. TR92D6726)
ON FRAME STEP
(Part No. TR92D8946)
DASH INDICA
T
OR P
ANEL
(Part No. TR94D2872)
ON DIAL-A-HEIGHT KNOB
(Part No. TR78D9740)
ON FRAME STEP
(Part No. TR92D6725)
ON DASH
LEFT SIDE
(Part No. TR92D6738)
ON DASH
RIGHT SIDE
(Part No. TR92D6739)
ON FRAME REAR
(Part No. TR92D6727)
ON STEERING T
OWER
(Part No. TR94D1863)
8
Gasoline and Oil
Recommended
Gasoline
Use UNLEADED Regular Gasoline suitable for
automotive use (85 pump octane minimum). Leaded
regular gasoline may be used if unleaded regular is
not available.
IMPORTANT: Never use methanol, gasoline
containing methanol, or gasohol containing
more than 10% ethanol because the fuel
system could be damaged. Do not mix oil with
gasoline.
POTENTIAL HAZARD
• In certain conditions gasoline is extremely
flammable and highly explosive.
WHAT CAN HAPPEN
• A fire or explosion from gasoline can burn
you, others, and cause property damage.
HOW TO AV
OID THE HAZARD
• Use a funnel and fill the fuel tank outdoors,
in an open area, when the engine is cold.
Wipe up any gasoline that spills.
• Do not fill the fuel tank completely full.
Add gasoline to the fuel tank until the level
is 1/4” to 1/2” (6 mm to 13 mm) below the
bottom of the filler neck. This empty space
in the tank allows gasoline to expand.
• Never smoke when handling gasoline, and
stay away from an open flame or where
gasoline fumes may be ignited by a spark.
• Store gasoline in an approved container
and keep it out of the reach of children.
Never buy more than a 30-day supply of
gasoline.
Filling
the Fuel T
ank
1. Shut the engine off and raise the seat.
2. Clean around the fuel tank cap and remove the
cap. Use a funnel and add unleaded regular
gasoline to the fuel tank, until the level is 1/4 to
1/2 inch (6 mm to 13 mm) below the bottom of
the filler neck. This space in the tank allows
gasoline to expand. Do not fill the fuel tank
completely full.
3. Install the fuel tank cap securely. Wipe up any
gasoline that may have spilled.
4. Low fuel level is viewed
through frame in rear of machine.
Check
Engine Oil Level
Before you start the engine and use the machine,
check the oil level in the engine crankcase; refer to
Checking Oil Level, page 20.
9
Operation
Think
Safety First
Please carefully read all the safety instructions on
pages 2–7. Knowing this information could help you,
your family, pets or bystanders avoid injury.
Controls
Become familiar with all the controls (Fig. 1) before
you start the engine and operate the machine.
2
15
4
8
9
10
12
2326
1
6
11
5
14
7
13
3
Figure 1
1. Steering
wheel
2.
Ignition switch
3.
Brake pedal
4.
Parking brake lever
5.
Ground speed selector
6.
Throttle lever
7.
Choke lever
8.
Power take of
f (PT
O)
9.
Indicator control
module/Hourmeter
10.
Attachment power lift
switch
11. T
ilt wheel lever
12.
Hood opening
13.
Dial-a-height knob
14.
Seat adjustment lever
15.
Cruise control switch
Parking Brake
Always set the parking brake when you stop the
machine or leave it unattended.
While the ignition key is in the “RUN” or “LIGHTS”
positions and the Parking Brake is engaged, the
Parking Brake light, in the Indicator Module, will be
lit.
Setting the Parking Brake
1. Push the brake pedal (Fig. 2) down and hold it in
the depressed position.
2. Lift the parking brake lever (Fig. 2) up and
gradually take your foot off the brake pedal. The
brake pedal should stay in the depressed (locked)
position.
Releasing the Parking Brake
1. Push down on the brake pedal (Fig. 2). The
parking brake lever should release.
2. Gradually release the brake pedal.
1
2
2327
Figure 2
1. Brake
pedal
2.
Parking brake lever
Operation
10
Starting
and Stopping
the Engine
Starting
1. Sit down on the seat.
2. Set the parking brake; refer to Setting the
Parking Brake, page 9.
Note: The engine will not start unless you set
the parking brake or fully depress the
brake pedal and are seated.
3. Push the PTO (power take off) to “OFF”
(Fig. 3).
4. Move the choke lever to “ON” (Fig. 3).
Note: An engine that has been running and is
warm may not require step 4.
5. Move throttle lever to “Fast” (Fig. 4).
6. Turn the ignition key clockwise and hold it in
the “START” position (Fig. 5). When the engine
starts, release the key.
IMPORTANT: If the engine does not start
after 30 seconds of continuous cranking, turn
the ignition key to “OFF” and let the starter
motor cool; refer to Troubleshooting, page 36.
7. After the engine starts, move the choke lever to
“OFF” (Fig. 4). If the engine stalls or hesitates,
move the choke lever back to “ON” for a few
seconds. Then move the throttle lever to desired
setting. Repeat this as required.
Figure 3
1. PTO-Off
2. Choke–On
3. Choke–Off
Figure 4
1. Fast
2. Slow
1
3
1207
1
2
1206
2
Figure 5
1. Off
2. Lights
3. Run
4. Start
3
2
1
1208
4
Stopping
1. Move the throttle lever to “SLOW” (Fig. 4).
2. Turn the ignition key to “OFF” (Fig. 5).
Note: If the engine has been working hard or
is hot, let it idle for a minute before
turning the ignition key “OFF.” This
helps cool the engine before it is
stopped. In an emergency, the engine
may be stopped by turning the ignition
key to “OFF.”
Operation
11
Operating
the
Power T
ake Off (PT
O)
The power take off (PT
O) engages and disengages
power to the electric clutch.
While the ignition key is in the “RUN” or “LIGHTS”
positions and the power take off (PTO) is engaged
“ON”, the PTO light, in the Indicator Module, will be
“ON”. When this light is “ON” it is a reminder; the
starter will not crank and to turn off PTO before
getting off.
Engaging the Power Take Off (PTO)
1. Depress the brake pedal to stop the machine.
2. Pull the power take off (PTO) to “ON” (Fig. 6).
1
1206
2
Figure 6
1. Off-Disengaged 2. On-Engaged
Disengaging the Power Take Off (PTO)
1. Depress the brake pedal to stop the machine.
2. Push the power take off (PTO) to “OFF”
(Fig. 6).
The
Safety Interlock System
Understanding the Safety Interlock
System
The safety interlock system is designed to prevent the
engine from starting unless:
• You are sitting on the seat
• The brake pedal is depressed
• The power take off (PTO) is “OFF”
The safety interlock system is designed to stop the
engine if you rise from the seat when the brake pedal
is released, the power take off (PTO) is “ON”.
Testing the Safety Interlock System
Test the safety interlock system before you use the
machine each time. If the safety system does not
operate as described below, have an Authorized
Service Dealer repair the safety system immediately.
1. Set the parking brake. Move the power take off
(PTO) to “ON”. Now turn the ignition key to
“START”; the engine should not crank.
2. Push the power take off (PTO) to “OFF” and
release the parking brake. Now turn the ignition
key to “START”; the engine should not crank.
3. Set the parking brake and move the power take
off (PTO) to “OFF”(On gear drive models the
speed selector lever must be in “N” neutral).
Now start the engine. While the engine is
running, release the parking brake and rise
slightly from the seat; the engine should stop.
Operation
12
Indicator
Control Module
The indicator control module (optional on some
models) (Fig. 7) lights when the parking brake or
power take off (PTO), is actuated and when there is a
problem of low oil pressure, battery or alternator
output that needs immediate attention.
7531 4
62
Figure 7
1. PTO
(power take of
f)
2. Temperature
3. Battery
4. Hourmeter
5.
Fuel Level
6. Oil
7.
Parking brake
Following are the conditions when indicator lights
will be “ON”. At other times the lights should be off.
Parking Brake
The parking brake light will be “ON” when the key is
in the “RUN” or “LIGHTS” positions and the parking
brake is secured with the parking brake lever raised.
When this light is “ON” it is a reminder; do not drive
machine with parking brake on and set parking brake
before getting off machine.
PTO (Power Take Off)
The PTO (power take off) light will be “ON” when
the key is in the “RUN” or “LIGHTS” positions and
the PTO (power take off) is engaged “ON”. When
this light is “ON” it is a reminder; the starter will not
crank and turn off the PTO before getting off.
Oil
The oil light will be “ON” when the key is in the
“RUN” or “LIGHTS” positions and the engine is not
running, after the engine is started the light should go
out. When the engine is running if the oil pressure
drops below a safe operating level the light comes
“ON”. When the light comes on while the engine is
running, Stop engine immediately and correct the
cause of low oil pressure.
Battery
The battery light will be “ON” when the key is in the
“RUN” or “LIGHTS” positions if the battery voltage
is below 12.6 volts or when the engine is running and
the alternator output is above 14.8 volts. When this
light comes on it is important to have your battery
and electrical system checked and the problem
corrected.
Furl Level
The fuel level light will be “ON” when the key in in
the “RUN” or “LIGHTS” positions and the fuel level
is low, approximately one pint remaining.
Temperature
The temperature light will be “ON” when the key in
in the “RUN” or “LIGHTS” positions and the engine
temperature exceeds proper operating limits. Stop
engine immediately and correct the cause of high
temperature.
Hourmeter
The hourmeter (optional on some models) records the
number of hours the engine has operated (Fig. 7). It is
turned on when the ignition switch is in the “RUN”
or “LIGHTS” positions. Use the times for scheduling
regular maintenance.
Operation
13
Driving
Forward or Backward
The throttle control regulates the engine speed as
measured in rpm (revolutions per minute). Place the
throttle control in the “FAST” position for best
performance.
To go forward or backward, release the parking brake:
refer to Releasing the Parking Brake, page 9. Place
your foot on the traction control pedal and slowly
press on the top of the traction control pedal to move
forward or on the bottom of the traction control pedal
to move backward (Fig. 8). The farther you move the
traction control pedal in either direction, the faster the
machine will move in that direction.
To slow down, release the pressure on the traction
control pedal.
IMPORTANT: To avoid transmission
damage, always release the parking brake
before moving the traction control pedal.
1
2
1210
Figure 8
1. Forward 2. Backward
Stopping
the Machine
To stop the machine, release the traction control
pedal, disengage the power take off (PTO), and turn
the ignition key to “OFF” to stop the engine. Also set
the parking brake if you leave the machine
unattended; refer to Setting the Parking Brake,
page 9. Remember to remove the key from the
ignition switch.
POTENTIAL HAZARD
• Someone could move or attempt to operate
the tractor while it is unattended.
WHAT CAN HAPPEN
• Children or bystanders may be injured if
they use the tractor.
HOW TO AV
OID THE HAZARD
•
Always r
emove the ignition key and set the
parking brake when leaving the machine
unattended, even if just for a few minutes.
Operation
14
Attachment
Power Lift
The attachment power lift (optional on some models)
(Fig. 9) is used to raise and lower attachments.
Raising Attachments
1. Turn key to the “ON” or “RUN” position
(Fig. 9).
2. Push the lift switch in the “UP” direction to raise
the attachment lift (Fig. 9). This will lift and
hold the attachment in the up, or raised position.
Lowering Attachments
1. Turn key to the “ON” or “RUN” position
(Fig. 9).
2. Push the lift switch in the “DOWN” direction to
lower the attachment lift (Fig. 9). This will lower
the attachment lift.
2266
2
1
3
Figure 9
1. Key
2. Lift
switch UP
3.
Lift switch DOWN
Adjusting
Dial-A-Height
The Dial-A-Height control (Fig. 9) is used to limit the
downward travel of the attachment. The
Dial-A-Height knob is rotated to change the location
of this stop, up or down.
1. Raise the attachment lift lever: Refer to Raising
Attachments. In the raised position the
Dial-A-Height knob (Fig. 9) can be rotated to
change the stop location. Turn clockwise to raise
and counterclockwise to lower the height of the
attachment.
2. The Dial-A-Height indicator (Fig. 9) will show
the change, high to low, in attachment lift height
as adjustment is made.
Operation
15
Positioning
the Seat
The seat can move forward and backward. Position
the seat where you have the best control of the
machine and are most comfortable.
1. Pull the seat adjustment lever toward the rear to
release the lock (Fig. 10).
2. Slide the seat to the desired position and release
the lever to engage lock.
1
1200
2
1229
Figure 10
1. Release
2. Lock
Headlights
The headlights are turned on with a separate position,
“LIGHTS”, of the ignition switch (Fig. 11). The
lights are on while the ignition switch is in the
“LIGHTS” position even with the engine off.
Remove the key when the machine is left unattended
so lights can not be turned on discharging the battery.
1208
1
Figure 1
1
1. Lights
Positioning
the
T
ilt Steering Wheel
The steering wheel has four tilt locations. Position the
steering wheel where you have the best control of the
machine and are most comfortable.
1. Lift the tilt lever to release the lock (Fig. 12).
2. Move the steering wheel to a comfortable
position; then release the lever to lock.
1
2
1203b
Figure 12
1. Tilt
lever
2.
Steering wheel
Operation
16
Using
the Cruise Control
The cruise control is optional on some models. A 3
position: Set-Lock (spring loaded), On and
Off-Unlock dash switch (Fig. 13) controls the
engagement. Cruise control maintains the traction
control position without foot pressure. Cruise control
is intended for operation in the forward direction
only. Do not use cruise control in reverse.
Engaging the Cruise Control
1. Begin driving tractor: Refer to Driving Forward
or Backward, Page 13. While holding your foot
steady on the traction control, push the cruise
control switch (Fig. 13) to the “SET”–“LOCK”
position.
1
2
1641t
Figure 13
1. Lock-Set 2. Unlock-Off
2. This locks the traction control in position and
your foot can then be removed from the traction
control. A constant pedal position will be
maintained.
Disengaging the Cruise Control
1. While holding your foot steady on the traction
control, move the cruise control switch (Fig. 13)
to the “UNLOCK”–“OFF” position.
2. This unlocks the traction control and your foot
then operates the traction control.
3. For quick stops, just press on the bake pedal.
This automatically disengages the cruise control
and applies the brake at the same time.
Pushing
the Machine by Hand
IMPORTANT: Always push the machine by
hand. Never tow the machine because
transaxle damage may occur.
To Push the Machine
1. Disengage the power take off (PTO) and turn the
ignition key to “OFF” to stop the engine.
2. Move the drive control rod to the “PUSH”
position. This disengages the drive system and
allows the wheels to turn freely (Fig. 14).
IMPORTANT: Drive control rod moves to the
“OPERATE” position when the brake is
applied.
To Operate the Machine
1. Apply the brake, this moves the drive control rod
to “OPERATE” and engages the drive system, or
move the drive control to the “OPERATE”
position (Fig. 14).
Note: The machine will not drive unless the
drive control rod is in the “OPERATE”
position.
1
2
1209
Figure 14
1. Operate
position
2.
Push position
17
Maintenance
Service
Interval Chart
Service
Operation
Each
Use
5
Hours
25
Hours
50
Hours
100
Hours
Storage
Service
Spring
Service
Oil—check level
X
Oil—change* Initial X
Oil Filter—change* (200 hours, every
other oil change or yearly)
X X
Safety System—check
X X
Brake—check X X X X
Chassis—grease* X X
Foam Air Cleaner—service*
X X
Paper Air Cleaner—replace*
X X
Spark Plug(s)—check 200 hours
X X
Belts—check for wear/cracks
X X
Gasoline—drain X
Engine—clean outside
X X X
Chipped Surfaces—paint
X
Battery—check electrolyte
X X X X
Battery—charge, disconnect cables
X
Fuel Filter—replace
X X
T
ires—check pressure
X X X
Front Wheels–check toe-in
X X
Power Lift–check fluid
X X X
T
ransaxle Fluid–check level
X X X
*
More often in dusty
, dirty conditions
POTENTIAL HAZARD
• If you leave the key in the ignition switch, someone could start the engine.
WHAT CAN HAPPEN
• Accidental starting of the engine could seriously injure you or other bystanders.
HOW TO AV
OID THE HAZARD
• Remove the key from the ignition switch and pull the wire(s) off the spark plug(s)
before you do any maintenance. Also push the wire(s) aside so it does not
accidentally contact the spark plug(s).
Maintenance
18
Air
Cleaner
Service Interval/Specification
Foam Element: Clean and re-oil after every 25
operating hours, or yearly, whichever occurs first.
Paper Element: Replace after every 100 operating
hours or yearly, whichever occurs first.
Note: Service the air cleaner more frequently
(every few hours) if operating
conditions are extremely dusty or
sandy.
Removing the Foam and Paper Elements
1. Disengage the power take off (PTO), set the
parking brake, and turn the ignition key to
“OFF” to stop the engine. Remove the key.
2. Open the hood.
3. Clean around the air cleaner to prevent dirt from
getting into the engine and causing damage.
Remove knob and the air cleaner cover (Fig. 15).
1
2
3
4
5
6
8
7
1213
Figure 15
1. Air
cleaner cover
2. Latches
3.
Cover nut
4. Cover
5.
Foam element
6.
Paper element
7.
Rubber seal
8.
Air cleaner base
4. Carefully slide the foam element off the paper
element (Fig. 15).
5. Unscrew the cover nut and remove the cover and
paper element (Fig. 15).
Cleaning the Foam and Paper Elements
1. Foam Element
A. Wash the foam element in liquid soap and
warm water. When the element is clean,
rinse it thoroughly.
B. Dry the element by squeezing it in a clean
cloth.
C. Put one or two ounces of oil on the element
(Fig. 16). Squeeze the element to distribute
the oil.
IMPORTANT: Replace the foam element if it
is torn or worn.
2
1213
1
Figure 16
1. Foam
element
2. Oil
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
New Holland LS55-19H User manual
- Category
- Lawnmowers
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI