Miele 10155130 User manual

de Gebrauchsanweisung Bodenstaubsauger

en Vacuum cleaner operating instructions

fr Mode d'emploi pour aspirateur traîneau

nl Gebruiksaanwijzing stofzuigers

it Istruzioni d'uso per aspirapolvere a traino

M.-Nr. 09 878 751

HS12

Page is loading ...

de - Anmerkung zu den Euro

-

päischen Regulierungen

665/2013 und 666/2013

Sollte Ihrem Staubsauger zusätzlich ein

Abluftfilter HEPA AirClean beiliegen, so

ist dieser durchgehend für alle in den

Europäischen Regulierungen 665/2013

und 666/2013 beschriebenen Einsatz

-

fällen bestimmt.

en - Notes on Delegated

Regulation (EU) No. 665/2013

and 666/2013

If your vacuum cleaner is also fitted

with a HEPA AirClean exhaust filter, it is

intended for all applications as

specified in European Delegated

Regulations 665/2013 and 666/2013.

fr - Notes sur les directives

européennes 665/2013 et

666/2013

Le filtre d'évacuation HEPA AirClean

éventuellement fourni avec votre aspi

-

rateur est conçu pour l'utilisation décri

-

te dans les directives européennes

665/2013 et 666/2013.

nl - Informatie met betrekking

tot de Europese verordeningen

665/2013 en 666/2013

Als bij uw apparaat ook een uitblaas-

filter HEPA AirClean is geleverd, is het

doorgaans bestemd voor alle toepas

-

singen die in de Europese verordenin

-

gen 665/2013 en 666/2013 worden be

-

schreven.

it - Note sui regolamenti euro

-

pei 665/2013 e 666/2013

Se con l’aspirapolver vi fosse in dota-

zione anche un filtro aria HEPA Air-

Clean, questo è adatto all’impiego in

tutti i casi descritti dai regolamenti

665/2013 e 666/2013.

Page is loading ...

Warning and Safety instructions ....................................21

Guide to the appliance ............................................26

Caring for our environment ........................................28

Preparing for use .................................................29

Using the accessories supplied .....................................30

Use ............................................................30

Unwind the mains cable ............................................30

To switch on and off................................................30

During vacuuming .................................................31

To regulate the suction power ........................................31

To open the air inlet valve ...........................................31

Parking and storing the cleaner .....................................31

Maintenance .....................................................32

Purchasing new dustbags and filters ..................................32

Ordering the correct dustbags and filters ...............................32

When to change the dustbag ........................................33

How the dustbag change indicator works...............................33

How to replace the dustbag .........................................33

When to change the dust compartment filter (for motor protection) ...........34

How to change the dust compartment filter .............................34

When to replace the AirClean exhaust filter .............................34

How to replace the AirClean filter .....................................34

Replacing one type of exhaust filter with another .........................34

When to replace an Active AirClean 30 / HEPA AirClean 30 filter.............34

How to replace an Active AirClean 30 filter or a HEPA AirClean 30 filter .......34

When to change the thread lifters .....................................35

How to replace the thread lifters ......................................35

Problem solving guide ............................................35

After sales service ................................................35

Guarantee .......................................................35

Electrical connection for the UK ....................................36

Electrical connection AU, NZ .......................................36

en - Contents

20

This vacuum cleaner complies with statutory safety

requirements. Improper use can, however, lead to

personal injury and damage to property.

To avoid the risk of accidents and damage to the

vacuum cleaner, please read these instructions carefully

before using it for the first time. They contain important

information on its safety, operation and maintenance.

Keep these instructions in a safe place and ensure that

new users are familiar with the content. Pass them on to

any future owner.

Always disconnect the vacuum cleaner from the mains

supply when you have finished using it, before changing

over accessories, as well as for maintenance work and

cleaning. Switch the vacuum cleaner off at the wall

socket and unplug it.

Correct application

~

This vacuum cleaner is intended for cleaning flooring in

domestic households and similar residential environments.

~

This vacuum cleaner is intended for daily cleaning of

carpets, rugs and robust hard flooring.

~

This vacuum cleaner is not intended for outdoor use.

en - Warning and Safety instructions

21

~

The vacuum cleaner must only be used to vacuum dry floor

surfaces. Do not use on people or animals. Any other usage,

modification or alteration is not supported by the

manufacturer and could be dangerous.

~

This vacuum cleaner can only be used by people with

reduced physical, sensory or mental capabilities, or lack of

experience or knowledge, if they are supervised whilst

using it or have been shown how to use it in a safe way

and understand and recognise the consequences of

incorrect operation.

Safety with children

~

Children under 8 years of age must be kept away from

the vacuum cleaner unless they are constantly supervised.

~

Children 8 years and older may only use the vacuum

cleaner unsupervised if they have been shown how to use

it safely and recognise and understand the consequences

of incorrect operation.

~

Children must not be allowed to clean or maintain the

vacuum cleaner unsupervised.

~

Please supervise children in the vicinity of the vacuum

cleaner and do not let them play with it.

Technical safety

~

Before using the vacuum cleaner and its accessories,

check for any visible signs of damage. Do not use a

damaged appliance.

en - Warning and Safety instructions

22

~

Ensure that the connection data on the data plate of the

vacuum cleaner (voltage and frequency) match the mains

electricity supply exactly. The vacuum cleaner is suitable

for use with 50Hz or 60Hz without modification.

~

The mains electrical plug must be fitted with a 13 A fuse

(UK).

~

Reliable and safe operation of this vacuum cleaner can

only be assured if it has been connected to the mains

electricity supply.

~

While the vacuum cleaner is under guarantee, repairs

should only be undertaken by a Miele authorised service

technician. Otherwise the guarantee will be invalidated.

~

Do not pull or carry the vacuum cleaner by the cable,

and be careful not to damage the cable when withdrawing

the plug from the socket.

Keep the cable away from sharp edges and do not let it

get squashed, for example, under a door.

Avoid running the vacuum cleaner over the cable. This

could damage the cable, plug or socket.

The appliance must not be used if any of these have

suffered damage.

~

Do not use the vacuum cleaner if the cable is damaged.

If the cable is damaged it must be replaced together with a

complete cable rewind. For safety reasons this work must

be done by the Miele Service Department or a Miele

authorised service technician.

en - Warning and Safety instructions

23

~

When vacuuming fine dust, e.g. sawdust, sand, plaster,

flour, talcum powder etc., electrostatic charges build up

naturally. Under certain conditions these charges will be

released. To avoid the unpleasant effects of these

discharges, a metal inlay has been incorporated into the

underside of the handle. Please make sure that you keep

your hand in constant contact with this metal strip during

vacuuming.

~

Do not let the vacuum cleaner get wet. Clean only with a

dry cloth or slightly damp cloth when disconnected from

the mains supply.

~

Repairs should only be carried out by a Miele authorised

service technician. Repairs and other work by unqualified

persons can cause considerable danger to users.

Correct use

~

To avoid the risk of damage, do not use the vacuum

cleaner without the dustbag, dust compartment filter and

exhaust filter in place.

~

The dust compartment cover will not close without a

dustbag fitted. Do not force it.

~

Do not vacuum up anything which has been burning or

is still glowing e.g. cigarettes, ashes or coal, whether

glowing or apparently extinguished.

~

Do not use the vacuum cleaner to vacuum up any water,

liquid or damp dirt. Wait until any freshly cleaned or

shampooed carpets or floor coverings are completely dry

before attempting to vacuum.

en - Warning and Safety instructions

24

~

Do not use the vacuum cleaner to vacuum toner dust.

Toner, such as that used in printers and photocopiers, can

conduct electricity.

~

Do not vacuum up any inflammable or combustible

liquids or gases and do not vacuum in areas where such

substances are stored.

~

Floor attachments, accessories and tubes must not be

used at head level to avoid the risk of injury, e.g. to eyes

and ears.

Accessories

~

To avoid the risk of injury when vacuuming with a Miele

Turbobrush, do not touch the rotating roller brush.

~

It is not advisable to vacuum directly with the handle,

i.e. without an accessory attached as the rim could get

damaged and you could hurt yourself on sharp edges.

~

Only use genuine dustbags, filters and accessories with

the "Original Miele" logo on them. Otherwise the

manufacturer cannot guarantee the safety of the product.

Miele cannot be held liable for damage caused by

incorrect use or operation or by non-compliance with

these Warning and Safety instructions.

en - Warning and Safety instructions

25

en - Guide to the appliance

26

a XXL handle *

b Handle *

c Air inlet valve

d Release buttons

e Connection piece for storage *

f Telescopic tube *

g Hose connection socket

h EasyLock suction tube *

i Release button for the telescopic tube *

j Dust compartment release catch

k Suction power selector

l Floorhead *

m Carrying handle

n Dustbag

o Dust compartment filter (for motor protection)

p AirClean filter

q On/Off foot control s

r Park system

s Mains cable

t Foot switch for automatic cable rewind

u Dustbag change indicator

v Accessories holder with three accessories

w Suction hose

Underneath - suction tube holder (not illustrated)

Features marked * depend on model and may vary or not be available on your

vacuum cleaner.

Optional accessories

Miele accessories are available to order from your Miele Dealer, the Miele Spare

Parts Department or via the internet at www.miele-shop.com.

en - Guide to the appliance

27

Disposal of packing material

The packaging is designed to protect

the vacuum cleaner from damage

during transportation. The packaging

materials used are selected from

materials which are environmentally

friendly for disposal and should be

recycled.

Recycling the packaging reduces the

use of raw materials in the

manufacturing process and also

reduces the amount of waste in landfill

sites.

Ensure that any plastic wrappings,

bags, etc. are disposed of safely and

kept out of the reach of babies and

young children. Danger of suffocation.

Disposing of the dustbag and

filters

These are made from environmentally

friendly materials. The filters can be

disposed of with the normal household

waste. The dustbag can also be

disposed of in this way if it has been

used exclusively for general household

dust.

Disposing of your old

appliance

Before disposing of your old appliance

remove the dustbag and all the filters

and dispose of them with your normal

household waste.

Electrical and electronic appliances

often contain valuable materials. They

also contain materials which, if handled

or disposed of incorrectly, could be

potentially hazardous to human health

and to the environment. They are,

however, essential for the correct

functioning of your appliance. Please

do not therefore dispose of it with your

household waste.

Please dispose of it at your local

community waste collection/recycling

centre, or contact your dealer for

advice.

Ensure that it presents no danger to

children while being stored for

disposal.

en - Caring for our environment

28

The illustrations referred to in the text

are shown on the fold-out pages at

the end of these operating

instructions.

Preparing for use

Attach the suction hose (dia. 1)

a Insert the hose connector into the

suction socket on the vacuum

cleaner until it clicks into position.

To detach the suction hose

b Press the release buttons at the side

of the hose connector, and lift the

hose from the socket.

Connect the handle to the suction

hose (dia. 2)

^ Fit the connector at the other end of

the suction hose into the handle until

it clicks into position.

Your vacuum cleaner is fitted with one

of the following tubes, depending on

model (see "Description of the vacuum

cleaner"):

–

EasyLock suction tube

–

Telescopic suction tube

To assemble the EasyLock tube

(dia. 3)

^

Hold the suction tube by the

connection piece and push it into the

second suction tube, turning it

clockwise or anti-clockwise until it

clicks into position.

^

Slide the connection piece upwards

until it clicks into position.

Attach the handle to the suction tube

(dia. 4)

a Insert the handle into the suction

tube until it clicks into position. To do

this, line up the guides on the two

pieces.

To detach the handle

b Press the release button and pull the

handle out of the suction tube,

twisting it slightly as you do so.

To adjust the telescopic tube (dia. 5)

One part of this telescopic tube is

packed inside the other and can be

adjusted to suit your height for

comfortable vacuum cleaning.

^ Press the release button (see arrow)

to release the tubes and adjust to the

required height.

Attach the standard floorhead (dia. 6)

a Push the suction tube into the

floorhead and turn it clockwise or

anti-clockwise until it clicks into

position.

To detach the floorhead

b Press the release button and pull the

suction tube away from the floorhead,

twisting it slightly as you do so.

To adjust the standard floorhead

This floorhead can be used for all

normal cleaning of carpets, rugs and

robust hard flooring.

Miele offer a range of other floorheads,

brushes and accessories for other

types of flooring and special

requirements.

en

29

Please observe the flooring

manufacturer's cleaning and care

instructions.

c Vacuum carpets and rugs with the

brush retracted (Press the % foot

control). Clean hard flooring with is

not susceptible to scratching, as well

as flooring with gaps or deep

crevices in it with the brush

protruding (press the ) foot control).

AirTeQ floorhead

If the suction power of the AirTeQ

floorhead seems too high, reduce

the suction until the floorhead is

easier to manoeuvre (see "Use - To

regulate the suction power").

Using the accessories

supplied (dia.7+8)

The following accessories are supplied:

a Dusting brush

b Upholstery nozzle

c Crevice nozzle

d Accessory holder for the three

accessories supplied:

Symbols on the holder show where to

attach the different accessories.

^

Attach the accessories holder to the

hose connector socket at the top or

bottom of the suction hose. Make

sure it clicks into position.

Depending on model, your vacuum

cleaner may be supplied with an Active

AirClean 30 or HEPA AirClean 30 filter

which can be fitted instead of the

standard AirClean filter (see

"Maintenance and care - Replacing one

type of exhaust filter with another").

Floorhead (dia. 9)

For general use and also for vacuuming

the stairs.

,

For safety reasons when

vacuuming stairs it is best to start at

the bottom of the stairs and move

upwards.

Use

Unwind the mains cable (dia. 10)

a Pull the mains cable out to the

required length (max. cable length

approx. 5.5 m). Insert the plug into

the socket correctly and switch on.

,

If vacuuming for longer than

30 minutes, the mains cable must

be pulled out to its fullest extent.

Otherwise there is a danger of

overheating and damage.

To rewind the cable

^

Switch off at the wall socket and

remove the plug.

b Press the rewind foot switch. The

cable will rewind automatically.

To switch on and off (dia. 11)

^

Press the On/Off foot control s.

en

30

During vacuuming (dia. 12)

,

When vacuuming fine dust, e.g.

sawdust, sand, plaster, flour, talcum

powder etc., electrostatic charges

build up naturally. Under certain

conditions these charges will be

released. To avoid the unpleasant

effects of these discharges, a metal

inlay has been incorporated into the

underside of the handle. Please

make sure that you keep your hand

in constant contact with this metal

strip during vacuuming.

To regulate the suction power

(dia. 13)

The suction power can be regulated to

suit the type of flooring being cleaned.

Reducing the suction power reduces

the amount of effort required to

manoeuvre the floorhead.

The vacuum cleaner has symbols on

the controls which indicate the type of

use the settings are suitable for.

# - curtains, fabric

$ - upholstery, cushions

% - thick pile carpets, rugs and

runners

* - for energy-saving vacuuming

(this setting is also very quiet)

( - loop pile carpet

) - heavily soiled hard flooring and

intensive cleaning of carpets

When using the AirTeQ floorhead, if

the suction seems too high, reduce

the suction until the floorhead is

easier to manoeuvre.

^

Turn the suction power selector

manually to the suction power setting

you require.

To open the air inlet valve (dia. 14 +

15)

It is easy to reduce the suction power

for a short time, e.g. to prevent rugs or

other objects being sucked into the

vacuum cleaner.

^ Open the air inlet valve on the handle

far enough to reduce the suction

power.

The floorhead will be easier to

manoeuvre. Close the valve up again

when you are ready to use full power

again.

Parking and storing the cleaner

Park system (dia. 16)

The Park system allows you to

conveniently park the suction tube and

floorhead during pauses.

^

Slot the floorhead into the parking

attachment at the back of the

vacuum cleaner.

If your vacuum cleaner is on a

sloping surface, e.g. a ramp,

- retract the telescopic tube fully

- do not use the park system if your

vacuum cleaner has an EasyLock

suction tube!

en

31

Storage (dia. 17 + 18)

^

Stand the vacuum cleaner upright.

^

Slot the floorhead downwards into the

parking attachment on the side of the

vacuum cleaner.

If your vacuum cleaner has a

telescopic tube, retract the tubes fully

so that it takes up less room for

storage.

If your vacuum cleaner has an

EasyLock suction tube you can

separate the two sections for storage

purposes.

^ Press the release button on the lower

section and pull the top section out.

^ Push the connection piece attached

to the upper tube into the lower tube.

Maintenance

,

Always disconnect the vacuum

cleaner from the electrical supply for

maintenance work and for cleaning.

Switch off at the wall socket and

unplug it.

The Miele filtration system consists of

three filters.

–

Dustbag

–

Dust compartment filter (for motor

protection)

–

Exhaust filter

These will need to be replaced from

time to time to ensure that your vacuum

cleaner performs efficiently.

Only use genuine dustbags, filters

and accessories with the "Original

Miele" logo on them. This will ensure

that the suction power of the

vacuum cleaner is maintained,

giving the best possible cleaning

results.

,

The use of dustbags made from

paper or paper-based materials, or

dustbags with a cardboard collar,

or dustbags that do not carry the

"Original Miele" logo, can seriously

damage the vacuum cleaner and

invalidate the warranty.

Purchasing new dustbags and filters

Original Miele dustbags and filters can

be ordered from Miele, your Miele

dealer or online at:

Ordering the correct dustbags and

filters

Only use original Miele G/N dustbags

with a blue collar and original Miele

filters. These are identified by the

"Original Miele" logo on the packaging

or directly on the dustbag.

en

32

An Air Clean filter and a dust

compartment filter are supplied with

every packet of Miele dustbags.

These can also be purchased

separately from your Miele Dealer, from

Miele or from the online shop. Please

quote the model number of your

vacuum cleaner when ordering to make

sure you get the correct filter.

When to change the dustbag (dia. 19)

Change the dustbag when the colour

marker in the dustbag change indicator

turns red, or sooner if it is no longer

effective (see possible reasons for this

below).

Miele dustbags are disposable and

designed for single use only.

Dispose of the dustbag when full.

Do not attempt to reuse. Blocked

pores in used dustbags will reduce

the suction power of the vacuum

cleaner.

Checking the dustbag change

indicator

^

Attach the standard floorhead to the

suction tube.

^

Switch the vacuum cleaner on and

select the highest power setting.

^

Lift the floorhead off the floor a little.

How the dustbag change indicator

works

The dustbag change indicator is set for

normal household dust. This generally

contains a mixture of: dust, hair,

threads, carpet fluff, grit etc.

However, if the cleaner has been used

to vacuum up fine dust, such as

plaster, brick dust, cement or flour, the

pores of the dustbag will become

blocked very quickly. This affects the

air permeability of the bag, and the

marker will indicate that the bag is "full"

even when it is not. If this happens you

must still change the dustbag because

suction power will be greatly reduced

by blocked pores in the dustbag.

If, on the other hand, a large amount of

hair and carpet fluff which typically

contains a lot of air is vacuumed up, the

indicator may fail to react even though

the bag is full. You should still change

it. Both these extremes can occur.

How to replace the dustbag (dia. 20 +

21)

^ Press the release catch for the dust

compartment lid and raise the lid as

far as it will go.

The dustbag has a closing flap which

closes automatically when the dust

compartment lid is raised to prevent

any dust escaping.

a Pull the dustbag out by the grip on

the collar.

b Fit the new dustbag into the holder

as far as it will go. Leave it folded up

when you take it out of the box.

^

It should be unfolded as far as

possible in the dust compartment.

^

Close the dust compartment lid

securely, making sure it clicks into

position. Take care not to trap the

dustbag when doing so.

The lid will not close without a

dustbag in place. Do not force it!

en

33

When to change the dust

compartment filter (for motor

protection)

Replace this filter every time you start a

new packet of dustbags. A dust

compartment filter is supplied with

every packet of Miele dustbags.

How to change the dust

compartment filter (dia. 22)

^

Open the dust compartment lid.

^

Unclip the filter frame and replace

the dust compartment filter.

^ Close the filter frame.

^ Close the dust compartment lid.

When to replace the AirClean

exhaust filter

Replace this filter every time you start a

new packet of Miele dustbags. An

AirClean exhaust filter is supplied with

every packet of Miele dustbags.

How to replace the AirClean filter

(dia. 23)

Do not use more than one exhaust

filter at a time.

^

Open the dust compartment lid.

a Release the filter grille and raise it

upwards. Grasp the used AirClean

filter by the clean, unsoiled section

(see arrow) and take it out.

b Replace it with a new filter.

^

Close the filter grille.

^

Close the dust compartment lid.

Replacing one type of exhaust filter

with another

Depending on model, your vacuum

cleaner may also be supplied with an

Active AirClean 30 or HEPA AirClean 30

filter which can be fitted instead of the

standard AirClean filter.

In order to use either of these filters you

first have to remove the AirClean filter

and the filter grille and replace these

with the new filter. You will also need to

active the exhaust filter change

indicator ~ (dia. 24).

After approx. 10 - 15 seconds a thin red

stripe will appear in the left hand side of

the display (dia. 25).

When to replace an Active AirClean

30 / HEPA AirClean 30 filter (dia. 26)

Replace if the display for the exhaust

filter change indicator is completely

filled with red.

This occurs after approx. 50 hours of

operation which is equivalent to about a

year of average use. The vacuum

cleaner can still be used. However, the

suction power will be reduced as will

the effectiveness of the filter if it is not

replaced in good time.

How to replace an Active AirClean 30

filter or a HEPA AirClean 30 filter

(dia. 27)

a Lift out the old exhaust filter.

b Replace it with a new filter.

en

34

When to change the thread lifters

The thread lifters on the suction inlet to

the floorhead can be replaced.

Check them from time to time and

replace them if the pile has worn down.

How to replace the thread lifters (dia.

28)

^

Use a suitable screwdriver to remove

the thread lifters from the slots.

^

Fit new thread lifters.

Replacement parts are available from

your Miele Dealer or from Miele (see

end of booklet for contact details).

Problem solving guide

The vacuum cleaner switches off

automatically.

A temperature limiter switches the

vacuum cleaner off automatically if it

gets too hot.

This can occur if, for instance, large

articles block the suction tube or when

the dustbag is full or contains particles

of fine dust. A heavily soiled exhaust or

dust compartment filter can also be the

cause of overheating. Switch the

vacuum cleaner off immediately using

the On/Off foot control s. Disconnect

from the electricity supply. Switch off at

the wall socket and unplug it.

After removing the cause, wait for

approximately 20 - 30 minutes to allow

the vacuum cleaner to cool down. It

can then be switched on again.

After sales service

In the event of a fault that you cannot

easily remedy, please contact

–

your Miele Dealer, or

–

Miele (see end of booklet for contact

details)

Please note that telephone calls may

be monitored or recored for training

purposes (UK only).

Guarantee

This appliance is guaranteed for 2

years from the date of purchase. In the

UK you must activate your cover by

calling 0845 365 6640 or registering

online at www.miele.co.uk.

For information on the appliance

guarantee specific to your country

please contact Miele. See end of

booklet for contact details.

en

35

Electrical connection for the

UK

All electrical work should be carried out

by a suitably qualified and competent

person in strict accordance with current

national and local safety regulations

(BS 7671 in the UK).

The voltage and frequency are given on

the data plate located underneath the

vacuum cleaner. Please ensure that

these match the household mains

supply. The fuse rating is quoted on the

plug.

The appliance is supplied with a cable

and moulded plug ready for connection

to a 230-240 V/50 Hz a.c. single phase

supply.

Non-rewireable plugs BS 1363

The fuse cover must be re-fitted when

changing the fuse, and if the fuse cover

is lost the plug must not be used until a

suitable replacement is obtained. The

colour of the correct replacement cover

is that of the coloured insert in the base

of the plug, or the colour that is

embossed in words on the base of the

plug, (as applicable to the design of

plug fitted).

Replacement fuses should be ASTA

approved to BS1362 and have the

correct rating. Replacement fuses and

fuse covers may be purchased from

your local electrical supplier.

Electrical connection AU, NZ

All work should be carried out by a

suitably qualified and competent

person in strict accordance with

national and local safety regulations.

The voltage and rated load are given

on the data plate located underneath

the vacuum cleaner. Please ensure that

these match the household mains

supply. The fuse rating is quoted on the

plug.

The appliance is supplied with a cable

and moulded plug ready for connection

to a 230V/50Hz AC single phase

supply.

Test Marks Electrical safety

RCM Mark

Electrically suppressed

according to AS/NZS 1044

en

36

Page is loading ...

en - Alteration rights reserved

United Kingdom

Miele Co. Ltd.

Fairacres, Marcham Road

A

bingdon, Oxon, OX14 1TW

Customer Contact Centre Tel: 0330 160 6600

E-mail: [email protected]

Internet: www.miele.co.uk

A

ustralia

Miele Australia Pty. Ltd.

A

CN 005 635 398

A

BN 96 005 635 398

1 Gilbert Park Drive, Knoxfield, VIC 3180

T

el: 1300 464 353

Internet: www.miele.com.au

Miele (Shanghai) Trading Ltd.

1-3 Floor, No. 82 Shi Men Yi Road

Jing' an District

200040 Shanghai, PRC

T

el: +86 21 6157 3500, Fax: +86 21 6157 3511

E-mail: [email protected], Internet: www.miele.cn

China

41/F - 4101, Manhattan Place

23 Wang Tai Road

Kowloon Bay, Hong Kong

T

el: (852) 2610 1331, Fax: (852)2610 1013

Email: [email protected]

Miele (Hong Kong) Limited

Miele India Pvt. Ltd.

Ground Floor, Copia Corporate Suites

Plot No. 9, Jasola

New Delhi - 110025

T

el: 011-46 900 000, Fax: 011-46 900 001

E-mail: [email protected], Internet: www.miele.in

India

Miele Ireland Ltd.

2024 Bianconi Avenue

Citywest Business Campus, Dublin 24

T

el: (01) 461 07 10, Fax: (01) 461 07 97

E-Mail: [email protected], Internet: www.miele.ie

Ireland

Malaysia

Miele Sdn Bhd

Suite 12-2, Level 12

Menara Sapura Kencana Petroleum

Solaris Dutamas No. 1, Jalan Dutamas 1

50480 Kuala Lumpur, Malaysia

Phone: +603-6209-0288

Fax: +603-6205-3768

Miele New Zealand Limited

IRD 98 463 631

Level 2, 10 College Hill

Freemans Bay, Auckland 1011, NZ

Tel: 0800 464 353

Internet: www.miele.co.nz

New Zealand

Miele Pte. Ltd.

163 Penang Road

# 04 - 03 Winsland House II

Singapore 238463

Tel: +65 6735 1191, Fax: +65 6735 1161

E-Mail: [email protected]

Internet: www.miele.sg

Singapore

Miele (Pty) Ltd

63 Peter Place, Bryanston 2194

P.O. Box 69434, Bryanston 2021

Tel: (011) 875 9000, Fax: (011) 875 9035

E-mail: [email protected]

Internet: www.miele.co.za

South Africa

Miele Appliances Ltd.

P.O. Box 11 47 82

Gold & Diamond Park, Sheikh Zayed Road

Building 6 / Offices Nos. 6-214 to 6-220

Dubai

Tel: +971-4-341 84 44

Fax: +971-4-341 88 52

E-Mail: [email protected]

Internet: www.miele.ae

United Arab Emirates

Carl-Miele-Straße 29, 33332 Gütersloh, Germany

Manufacturer:

Miele & Cie. KG

Page is loading ...

Miele 10155130 User manual

This manual is also suitable for

Miele 10155130 User manual

in other languages

Related papers

Other documents