Regency Fireplace Products Plateau PTO30CKT Owner's manual

Brand
Regency Fireplace Products
Model
Plateau PTO30CKT
Category
Fireplaces
Type
Owner's manual

This manual is also suitable for

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
919-108a
06/25/13
Owners &
Installation Manual
Tested by:
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
MODELS: PTO30CFT-1
PTO30IST-1
PTO30CKT-1
Regency Plateau
®
Series
Outdoor Decorative Gas Appliances
WARNING: FOR OUTDOOR USE ONLY
www.regency-fi re.com
WARNING:
If the information in these instructions
are not followed exactly, a fire
or explosion may result causing
property damage, personal injury or
loss of life.
WARNING - FOR YOUR SAFETY
What to do if you smell gas:
•Shut off gas to the appliance.
•Do not try to light any appliance.
•Extinguish any open fl ame.
•If odor continues, keep away from the appliance and im-
mediately call your gas supplier or fi re department.
•Do not touch any electrical switch: do not use any phone
in your building.
•Immediately call your gas supplier from a neighbour's
phone.
•Follow the gas supplier's instructions.
•If you cannot reach your gas supplier, call the fi re
department.
WARNING:
Improper installation, adjustment,
alteration, service or maintenance
can cause injury or property damage.
Read the installation, operating and
maintenance instructions thoroughly
before installing or servicing this
equipment.
Installation and service must be
performed by a qualifi ed installer,
service agency or the gas supplier
WARNING:
Do not store or use gasoline or other fl ammable vapours
and liquids in the vicinity of this or any other appliance.
A LP - cylinder not connected for use shall not be
stored in the vicinity of this or any other appliance.
Regency Plateau® Outdoor Firetables Video
2
Regency Plateau
®
Series Outdoor Gas Fireplace
DANGER
CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide
which has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space
such as a camper, tent, car or home.
X
X
X
To the New Owner:
Congratulations!
You are the owner of a state-of-the-art Outdoor Decorative Gas Appliance by REGENCY
®
. The
Plateau® Series Outdoor Decorative Gas Appliance has been designed to provide you with all
the warmth and charm of a fi re at the fl ick of a switch. The Plateau
®
Series Outdoor Decorative
Gas Appliance has been approved by Warnock Hersey/Intertek for both safety and effi ciency.
As it also bears our own mark, it promises to provide you with economy, comfort and security
for many trouble free years to follow. Please take a moment now to acquaint yourself with these
instructions and the many features of your Regency
®
decorative gas appliance.
PTO30CFT
PTO30IST
PTO30CKT
Regency Plateau
®
Series Outdoor Gas Fireplace
33
TABLE OF CONTENTS
SAFETY LABEL
Copy of Safety Decal .....................................................4
DIMENSIONS
Unit Dimensions - Coffee table ......................................5
Unit Dimensions - Island table .......................................6
Unit Dimensions - Cocktail table....................................7
INSTALLATION
Important Message ......................................................8
Before You Start ............................................................8
General Safety Information............................................8
Installation Checklist .....................................................9
Locating Your Outdoor decorative gas appliance ..........9
Important things to remember .....................................10
Minimum Clearances to combustibles .........................11
High Elevation .............................................................12
Gas Line Installation ....................................................12
Pilot Adjustment ...........................................................12
Gas Pipe Pressure Testing ..........................................12
886 S.I.T. Valve Description .........................................12
Aeration Adjustment ....................................................12
Wiring Diagram ............................................................13
Caster installation ........................................................14
Gas Connection ..........................................................15
Conversion from Ng to Lp............................................16
LP Tank installation - Pto30cft only ..............................18
LP Tank Installation ....................................................19
PTO30IST/PTO30CKT ONly ......................................19
LP Tank removal ........................................................19
Switch connection........................................................20
Battery Install ...............................................................20
Table top Installation - coffee table unit .......................21
Table top installation ...................................................22
(For Island and cocktail units only) ..............................22
Glass Crystal / Basalt volcanic stones installation ......23
Optional volcanic stone Installation .............................24
Optional Log Set Installation........................................25
Optional glass surround Installation ............................27
Riser Installation ..........................................................28
(to convert Island into cocktail table) ...........................28
Plateau® table cover Installations ...............................30
OPERATING INSTRUCTIONS
Operating Instructions .................................................31
Lighting Procedure ......................................................31
Shutdown Procedure ...................................................31
First Fire ......................................................................31
Copy of Lighting Plate Instructions ..............................32
Maintenance Instructions.............................................33
Switch replacement .....................................................34
Valve assembly replacement .......................................35
Digital fi replace control replacement ...........................36
Battery replacement ....................................................36
PARTS
Parts ............................................................................37
WARRANTY
Limited Warranty: ......................................................39
4
Regency Plateau
®
Series Outdoor Gas Fireplace
SAFETY LABEL
This is a copy of the label that accompanies each
Regency
®
Series Outdoor decorative gas appliance.
We have printed a copy of the contents here for
your review.
NOTE: Regency
®
units are constantly being
improved. Check the label on the unit and if there is
a difference, the label on the unit is the correct one.
COPY OF SAFETY DECAL
For the State of Massachusetts, installation and
repair must be done by a plumber or gas fi tter
licensed in the Commonwealth of Massachusetts.
For the State of Massachusetts, fl exible connec-
tors shall not exceed 36 inches in length.
For the State of Massachusetts, the appliances
individual manual shut-off must be a t-handle
type valve.
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER CETTE ÉTIQUETTE
386
386
FPI Fireplace Products International Ltd.
6988 Venture St.
Delta, BC, Canada V4G 1H4
Minimum Clearances to Combustibles /
Degagement Minimum De Materiaux Combustibles
Serial No./ No de serie
Listed:
Certified for/Certifi e pour:
Tested to:
OUTDOOR DECORATIVE GAS APPLIANCE /
CANADA and U.S.A.
EXTÉRIEUR DÉCORATIFS APPAREIL À GAZ
(US) / CR97-003 (CAN) / CAN / CGA-2.17-M91
é
ANSI Z21.97-2010
.
NOT FOR USE WITH SOLID FUELS. /
NE PAS UTILISER AVEC DES COMBUSTIBLES SOLIDE.
Made in Canada/ Fabrique au Canada
Duplicate S/N
ÉÉ
é
QUIP A L'UISINE POUR GAZ PROPANE
CONCU POUR ETRE POELE: Mod le PLATEAU SÉRIE
PROPANE GAS: Model SERIESPLATEAU
NATURAL GAS: Model SERIESPLATEAU
Minimum supply pressure
Manifold pressure high
Manifold pressure low
Orifice size
Maximum input
Minumum input
Altitude
Maximum supply pressure
Pression d'allimentation minimum
Pression à la tubulure d' chappement lev e
Grandeur de l'injecteur
D bit maximum selon
l'altitude
Pression d'allimentation maximum
Pression à la tubulure d' chappement
Calorifique
D bit Calorifique minimum selon
ééé
é
é basse
é
14” WC/C.E. (3.49 kPa)
5" WC/C.E. (1.25 kPa)
WC/C.E.
1.6" WC/C.E. (0.40 kPa)
50,000 Btu/h (14.65 kW)
30,000 Btu/h (8.79 kW)
3.5" (0.87 kPa)
#25 DMS
0-4500 ft/pi (0-1372 m)
Pression d'allimentation minimum
Pression à la tubulure d' chappement lev e
Grandeur de l'injecteur
D bit maximum selon
l'altitude
Pression d'allimentation maximum
Pression à la tubulure d' chappement
Calorifique
D bit Calorifique minimum selon
ééé
é
é basse
é
14" WC/C.E. (3.49 kPa)
11” WC/C.E. (2.74 kPa)
WC/C.E.
6.4" WC/C.E. (1.59 kPa)
49,000 Btu/h (14.36 kW)
38,000 Btu/h (11.13 kW)
10” (2.49 k Pa)
#45 DMS
0-4500 ft/pi (0-1372 m)
Minimum supply pressure
Manifold pressure high
Orifice size
Maximum input
Altitude
Maximum supply pressure
Manifold pressure low
Minumum input
Back Wall
A 17” (432mm)
B 17” (432mm)
C 45” (1143mm)
D 1” (25mm)
Side Wall
Ceiling
Floor
The installation must conform with local codes or, in the absence of local codes, with The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of
local codes, with the Canadian Electrical Code, CSA C22.1 or with the National Electrical Code, ANSI/NFPA 70. This appliance is only for use with the type of gas indicated on the rating plate . See owner's manual for details.
L'installation doit être conforme aux codes locaux ou, en l'absence de codes locaux, avec CAN/CSA-B149.1, gaz naturel et du propane ou du Code d'installation au ANSI Z223.1/NFPA54.
L'appareil, une fois installé, doit être connecté électriquement à la terre conformément aux codes locaux ou, en l'absence de codes locaux, avec le Code canadien de l'électricité, CSAC22.1 ou avec le National Electrical Code, ANSI / NFPA70.
Cet appareil est à utiliser uniquement avec le type de gaz indiqué sur la plaque signalétique. Voir le manuel du propriétaire pour les détails.
CAN/CSA-B149.1, Natural Gas and Propane Installation Code or ANSI Z223.1/NFPA 54.
APPAREIL FONCTIONNANT AU NATURAL GAS
CONCU POUR ETRE POELE: Mod leé PLATEAU SÉRIE
FOR OUTDOOR USE ONLY / POUR USAGE EXTÉRIEUR SEULEMENT
IF STORED INDOORS, DETACH AND LEAVE CYLINDER OUTDOORS /
SI VOUS LE GARDER À L'INTÉRIEUR, DETACHER LE CYLINDRE ET LAISSER À L'EXTÉRIEUR
919-015
PTO30CFT-NG
PTO30IST-NG
PTO30CKT-NG
PTO30CFT-LP
PTO30IST-LP
PTO30CKT-LP
A
C
D
B
MODEL:
4001172
Regency Plateau
®
Series Outdoor Gas Fireplace
5
DIMENSIONS
2-9/16”(64mm)
1” (25mm)
2-7/8”(73mm)
40-5/8”(1030mm)
1-3/8”(35mm)
38”(965mm)
-
FLOOR LEVEL
16-11/16”(423mm)
17-7/8”(454mm)
19-1/4”(490mm)
5-5/8”(143mm)
2-1/16”(52mm)
11LB TANK
11LB
TANK
TO
P
VIEW
SIDE VIEW
END VIEW
12-7/8"
38" (965mm)
5-1/16"
5-5/8"
48" (1219mm)
(352mm)
(143mm)
24" (610mm)
(129mm)
UNIT DIMENSIONS - COFFEE TABLE
Floor to bottom
of LP tank
NOTE: Optional glass surround shown
6
Regency Plateau
®
Series Outdoor Gas Fireplace
DIMENSIONS
28-7/8”
(733mm)
40-3/8”
(1031mm)
3-1/8”
(79mm)
Floor to
bottom of LP
tank
1”
(25mm)
1-5/8”
(39mm)
6-3/16
”
(156mm)
20-11/16”
(525mm)
Floor level
20lb tank
20lb tank
36" (914mm)
GLASS
TO
OUTER EDGE
BURNER
TO
OUTER EDGE
62" (1575mm)
14-1/4" (361mm)
12-3/16" (309mm)
GLASS
TO
OUTER EDGE
BURNER
TO
OUTER EDGE
14-1/4" (361mm)
11-3/4" (298mm)
36" (914mm)
UNIT DIMENSIONS - ISLAND TABLE
NOTE: For optional glass surround dimensions - see previous page.
Regency Plateau
®
Series Outdoor Gas Fireplace
7
DIMENSIONS
UNIT DIMENSIONS - COCKTAIL TABLE
37
15
16
"
963mm
42
3
16
"
1072mm
12
7
8
"
326.mm
49
1
8
"
1248mm
5
5
16
"
135mm
12
13
16
"
325mm
914mm
29
1
4
"
742mm
TOP VIEW
SIDE VIEW END VIEW
36" (914mm)
GLASS
TO
OUTER EDGE
BURNER
TO
OUTER EDGE
62" (1575mm)
14-1/4" (361mm)
12-3/16" (309mm)
GLASS
TO
OUTER EDGE
BURNER
TO
OUTER EDGE
14-1/4" (361mm)
1-3/4" (298mm)
36"
NOTE: Optional glass surround shown
8
Regency Plateau
®
Series Outdoor Gas Fireplace
INSTALLATION
IMPORTANT MESSAGE
SAVE THESE
INSTRUCTIONS
The Plateau
®
Series Outdoor Decorative Gas
Appliance must be installed in accordance with
these instructions. Carefully read all the instructions
in this manual fi rst. Consult the "authority having
jurisdiction" to determine the need for a permit prior
to starting the installation. It is the responsibility of
the installer to ensure this decorative gas appliance
is installed in compliance with manufacturers
instructions and all applicable codes.
BEFORE YOU START
Safe installation and operation of this appliance
requires common sense, however, we are required
by the Canadian Safety Standards and ANSI
Standards to make you aware of the following:
GENERAL SAFETY
INFORMATION
1) The installation must conform with local
codes or, in the absence of local codes, with
CAN/CSA-B149.1, Natural Gas and Propane
Installation Code or CAN/CSA-B149.2, Propane
installation code the Natural Gas Fuel Code,
ANSI Z223.1/NFPA 54.
2) See general construction and assembly
instructions. The appliance should be enclosed.
3) The LP-gas supply cylinder to be used must
be:(a)Constructed and marked in accordance
with the U.S. Department of Transportation
(D.O.T.) Specifi cations for LP-Gas Cylinders,
or the Standard for Cylinders, Spheres
and Tubes for Transportation of Dangerous
Goods and Commission, CAN/CSA-B339 as
applicable; (b)Provided with a listed overfi lling
prevention device; and(c)Provided with a
cylinder connection device compatible with the
connection for the appliance.
4) Inspect the burner before each use of the
appliance for blockage and any signs of
deterioration.
CHILDREN AND ADULTS SHOULD BE
ALERTED TO THE HAZARDS OF HIGH
SURFACE TEMPERATURES, ESPE-
CIALLY THE DECORATIVE GAS APPLI-
ANCE GLASS AND FACEPLATE, AND
SHOULD STAY AWAY TO AVOID BURNS
OR CLOTHING IGNITION.
THIS APPLIANCE SHALL BE USED
ONLY OUTDOORS IN A WELL-VENTI-
LATED SPACE AND SHALL NOT BE
USED IN A BUILDING, GARAGE OR ANY
OTHER ENCLOSED AREA.
INSTALLATION AND REPAIR SHOULD
BE DONE BY AN AUTHORIZED SERVICE
PERSON. THE APPLIANCE SHOULD
BE INSPECTED BEFORE USE AND AT
LEAST ANNUALLY BY A PROFESSIONAL
SERVICE PERSON. IT IS IMPERATIVE
THAT CONTROL COMPARTMENTS,
BURNERS AND CIRCULATING AIR
PASSAGEWAYS OF THE APPLIANCE
BE KEPT CLEAN.
ANY GUARD OR OTHER PROTECTIVE
DEVICE REMOVED FOR SERVICING
THE APPLIANCE MUST BE REPLACED
PRIOR TO OPERATING THE APPLIANCE
WARNING: FAILURE TO INSTALL THIS
APPLIANCE CORRECTLY WILL VOID
YOUR WARRANTY AND MAY CAUSE A
SERIOUS FIRE.
CLOTHING OR OTHER FLAMMABLE
MATERIAL SHOULD NOT BE PLACED
ON OR NEAR THE APPLIANCE.
SOLID FUELS SHALL NOT BE BURNED
IN THIS APPLIANCE.
DO NOT USE THIS APPLIANCE IF
ANY PART HAS BEEN UNDER WATER.
IMMEDIATELY CALL A QUALIFIED
SERVICE TECHNICIAN TO INSPECT
THE APPLIANCE AND TO REPLACE
ANY PART OF THE CONTROL SYSTEM
AND ANY GAS CONTROL WHICH HAS
BEEN SUBMERGED UNDER WATER.
YOUNG CHILDREN SHOULD BE CARE-
FULLY SUPERVISED WHEN THEY ARE
IN THE SAME AREA AS THE APPLI-
ANCE. TODDLERS, YOUNG CHILDREN
AND OTHERS MAY BE SUSCEPTIBLE
TO ACCIDENTAL CONTACT BURNS. A
PHYSICAL BARRIERS IS RECOMMEND-
ED IF THERE ARE AT RISK INDIVIDUAL
IN THE HOUSE. TO RESTRICT ACCESS
TO A DECORATIVE GAS APPLIANCE
OR STOVE, INSTALL AN ADJUSTABLE
SAFETY GATE TO KEEP TODDLERS,
YOUNG CHILDREN AND OTHER AT RISK
INDIVIDUALS OUT OF THE ROOM AND
AWAY FROM HOT SURFACES.
5) DO NOT SIT OR STAND ON DECORATIVE
GAS APPLIANCE
6) To prevent injury, do not allow anyone who
is unfamiliar with the operation to use the
decorative gas appliance.
7) Wear gloves and safety glasses for protection
while doing required maintenance.
8) Maximum gas inlet pressure = 1/2 psig.
9) Under no circumstances should this appliance
be modifi ed. Parts that have to be removed for
servicing should be replaced prior to operating
this appliance.
10) Installation and any repairs to this appliance
should be done by a qualifi ed service person.
A professional service person should be called
to inspect this appliance annually. Make it a
practice to have all of your gas appliances
checked annually.
11) Under no circumstances should any solid fuels
(wood, paper, cardboard, coal, etc.) be burned
in this appliance.
12) The appliance and its individual shutoff valve
must be disconnected from the gas supply
piping system during any pressure testing of
that system at test pressures in excess of 1/2
psi (3.5kPa).
The appliance must be isolated from the gas
supply piping system by closing its individual
manual shutoff valve during any pressure testing
of the gas supply piping system at test pressures
equal to or less than 1/2 psi (3.5 kPa).
13) The appliance area must be kept clear and
free of combustible materials, (gases and other
fl ammable vapours and liquids).
It is highly recommended to protect the
interior from moisture (rain, snow). Cover
the enclosure opening when not in use. This
decorative gas appliance is only for use
with the type of gas indicated on the rating
plate. This decorative gas appliance is not
convertible for use with other gases, unless a
certifi ed kit is used.
14) Cover must be removed when burner is in
operation.
15) When not using appliance for extended periods
of time - turn off gas supply.
16) The 4 levelling legs or optional casters on this
appliance must not be removed. These are for
safety and must remain on the appliance.
Emissions from burning wood or gas could
contain chemicals known to the State of
California to cause cancer, birth defects or
other reproductive harm.
Regency Plateau
®
Series Outdoor Gas Fireplace
9
INSTALLATION
INSTALLATION
CHECKLIST
1) Appliance is factory equipped for Natural Gas.
When using Propane, see LP conversion section
in this manual. For LP - use a maximum 11
pound tank or direct hard pipe from an external
LP supply.
2) Locate appliance:
a) Refer to "Locating Your Outdoor decorative
gas appliance" section
b) Clearances to Combustibles (Refer to
"Clearances" section)
3) Gas Connection - for ease of installation and
gas connection, remove left side panel
(one facing ON/OFF switch. Test for leaks..
4) Install 4 "AA" batteries into battery pack and
replace into battery compartment holder.
DO NOT USE A 9V battery.
5) Connect the ON/OFF switch wires to the switch.
6) Install standard and optional features. Refer to
the following sections:
a. Tabletop Installation
b. Glass Crystals
c. Volcanic Stone Installation (optional)
d. Log Installation (optional)
e. Glass Surround Installation (optional)
f. Weather Cover Installation
7) Final check.
This includes:
1) Clocking the appliance to ensure the correct
fi ring rate (rate noted on label), after burning
appliance for 15 minutes.
2) If required, adjusting the primary air to ensure
that the fl ame does not carbon. First allow the
unit to burn for 15-20 min. to stabilize.
CAUTION: Any alteration to the product that
causes sooting or carboning that results in dam-
age is not the responsibility of the manufacturer.
LOCATING YOUR
OUTDOOR DECORATIVE GAS APPLIANCE
1) When selecting a location for your outdoor decorative gas appliance, ensure that the clearances are
met.
2) This appliance must be installed in an open-air situation with natural ventilation, without stagnant
areas, where gas leakage and products of combustion are rapidly dispersed by wind and natural
convection.
3) Certain materials or items, when placed under or near the appliance, will be subjected to radiant
heat and could become damaged.
4) Typically an outdoor space is not enclosed but, any enclosure in which the appliance is used shall
comply with one of the following:
An enclosure with walls on all sides, but at least one permanent opening at ground level and no
overhead cover.
Within a partial enclosure that includes an overhead cover and no more that two walls.
Within a partial enclosure that includes an overhead cover and more than two walls, the following
shall apply:
• At least 25% of the total wall area is completely open, and
• At least 30% of the remaining wall area is open and unrestricted
30% or more in total of the remaining wall
area is open and unrestricted.
Open side at least 25% of total wall area
*SEE IMPORTANT INSTALLATION NOTES NEXT PAGE
10
Regency Plateau
®
Series Outdoor Gas Fireplace
INSTALLATION
• Never insulate around the body of the unit
• Excessive heat retention in the fi rebox will lead to component failure
and fi replace malfunction
• Excessive heat retention will also increase the risk of fi re inside the
chase
• Heat retention can cause “Oil-canning” and damage the fi replace due
to overheating
• Do not build up a wall of any type in front or to the sides of the appli-
ance, higher than the fi rebox opening. This will create a pressure zone
at the fi rebox and will prevent the unit from venting
• This is an outdoor appliance with a built-in drain. This drain should be
installed and connected in all applications as per the instructions in
this manual
• Inadequate drainage will cause rust and reduce the life of your appli-
ance, this is not protected by warranty
• Outdoor units use the same consistent, reliable Electronic components
used in most Regency “E” units
• Installed correctly, these components will be subjected to far lower
temperatures than indoor units, which have been certifi ed as safe from
heat etc
• Working gas pressures are as critical in outdoor products as they are
in indoor products, even more important in Electronic systems
• Unit shutting down intermittently
• Overheating of components leading to failure
• Lifting fl ame
• Poor fl ame package (i.e. all to one side, lazy fl ame)
• Failure to ignite
• Excess carbon
• Safety issues and concerns created from the byproducts of combus-
tion
• Outdoor appliances must be installed in: open-air situations with natu-
ral ventilation and without stagnant areas
• Any gas leakage and products of combustion need to be rapidly dis-
persed by wind and natural convection
• Typically outdoor spaces are not enclosed, however, failure to adhere
to installation guidelines, may cause the outdoor fi replace to be af-
fected by wind or air pressure inside the enclosure
• ANY enclosure in which the appliance is used shall comply with one of
the diagrams on the previous page.
• All walls + overhead cover = 100% total area
• One of four walls or full overhead area must be totally open, plus—one
of remaining walls must have a fi xed opening
• All outdoor fi replaces/fi re tables require total natural ventilation of 50%
open space
• Correct Working Gas pressure is critical on “E” units
• Wherever possible avoid locating on a fl at wall in a tight corner
• Floor space doesn’t count as “open area”
• Install to the manual specs for framing and do not insulate unit or
enclosure
• Framing enclosure must at least meet minimum dimensional specs as
per the installation manual
• Only Regency approved media should be used in the fi rebox (i.e.
stones/glass)
• Be aware of pressure zones due to location (i.e. facing the ocean)
• Open walls and doorways to outside air are benefi cial to the perfor-
mance of an outdoor appliance
• Fixed roof/ceiling open areas count towards the total open area overall
requirement
• Screens create 40% or more air restriction
• Screened areas are restrictions and reduce open air space, calculate
area based on a closed screen
• The biggest problems are created by lack of airfl ow for the appliance
• Outdoor fi replaces are often built-in systems and incorrect installation
can result in high repair costs
• Units must not be modifi ed or altered in any way
• There is a common misconception that being outdoors, an Outdoor
Fireplace will function, regardless of circumstances,
• Outdoor fi replaces require the same amount of ventilation as indoor
units, often more
• Outdoor units require adequate ventilation to the atmosphere, which in
turn provides ongoing circulatory combustion air
• This type of Appliance Vents.
• All Outdoor Fireplace Products have the same need for Air/Oxygen,
and an ability to Vent
• Even though the appliance is outdoors, this doesn’t mean it is getting
adequate air
• Requirements are not specifi c to Regency units
• Read and follow critical location guidelines in this manual
•
• Don’t overlook the obvious
• Widen your margin for error
• Combustion always requires the same three elements
• Only the quantities and volumes change
IMPORTANT INFORMATION FOR OUTDOOR FIREPLACE INSTALLATIONS
IMPORTANT THINGS TO REMEMBER
ANTICIPATED ISSUES CAUSED BY
INCORRECT LOCATION OR INSTALLATION
OUTDOOR APPLIANCES REQUIRE VENTING
COMPONENTS IN OUTDOOR APPLIANCES
COMMON MISCONCEPTIONS REGARDING
OUTDOOR FIREPLACES
UNDERSTANDING OUTDOOR APPLIANCE
REQUIREMENTS
OUTDOOR APPLIANCE INSTALLATION SUMMARY
Regency Plateau
®
Series Outdoor Gas Fireplace
11
INSTALLATION
Caution Requirements
The top, back and sides of the decorative gas appliance
are defi ned by standoffs. The metal ends of the
standoff may NOT be recessed into combustible
construction.
WARNING
Fire hazard is an extreme risk
if these clearances (air space) to combustible materials are not
adhered to. It is of greatest importance that this decorative gas
appliance be installed only in accordance with these instructions.
MINIMUM CLEARANCES TO COMBUSTIBLES
The clearances listed below are Minimum distances unless otherwise stated:
A major cause of fi res is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this
decorative gas appliance be installed only in accordance with these instructions.
Plateau® Series Clearance Requirements
Clearance: Dimension Measured From:
A: Back wall
17" (432mm) Burner to back wall
B: Sidewall
17" (432mm) Burner to sidewall
C: Ceiling
45" (1143mm) Burner to Ceiling
D
1
: Floor
D
2
: Floor
0" When using supplied leveling legs or optional casters.
1"(25mm) Unit Base to Floor
E: Alcove Width
84"(2134mm) Wall to Wall (Minimum)
F: Alcove Depth
60" (1524mm) Front to Back Wall (Maximum)
Notes:
0" No Hearth Required
E
F
Alcove
A
C
D
B
12
Regency Plateau
®
Series Outdoor Gas Fireplace
INSTALLATION
GAS PIPE PRESSURE
TESTING
The appliance must be isolated from the gas sup-
ply piping system by closing its individual manual
shut-off valve during any pressure testing of the
gas supply piping system at test pressures equal
to or less than 1/2 psig. (3.45 kPa). Disconnect
piping from valve at pressures over 1/2 psig.
The manifold pressure is controlled by a regulator
built into the gas control, and should be checked
at the pressure test point.
Note: To properly check gas pressure, both
inlet and manifold pressures should be
checked using the valve pressure ports
on the valve.
1) Make sure the valve is in the "OFF" position.
2) Loosen the "IN" and/or "OUT" pressure tap(s),
turning counterclockwise with a
1/8" wide fl at screwdriver.
3) Attach manometer to "IN" and/or "OUT" pressure
tap(s) using a 5/16" ID hose.
4) Light the pilot and turn the valve to "ON" position.
5) The pressure check should be carried out with
the unit burning and the setting should be within
the limits specifi ed on the safety label.
6) When fi nished reading manometer, turn off the
gas valve, disconnect the hose and tighten the
screw (clockwise) with a 1/8" fl at screwdriver.
Note: Screw should be snug, but do not over
tighten.
AERATION ADJUSTMENT
The burner aeration is factory set but may need
adjusting due to either the local gas supply or
altitude. Open the air shutter for a blue fl ame or
close for a more yellow fl ame.
Minimum Air Shutter Opening:
Fully Closed NG
1/2" LP
Note: Any damage due to carboning resulting
from improperly setting the aeration
controls is NOT covered under warranty.
HIGH ELEVATION
This unit is approved for altitude 0 to 4500 ft. (CAN/
CGA 2.17-M91).
GAS LINE
INSTALLATION
Since some municipalities have additional local
codes it is always best to consult with your local
authorities and the CAN/CGA B149 installation
code.
For USA installations follow local codes and/or the
current National Fuel Gas Code, ANSI Z223.1.
When using copper or fl ex connectors use only
approved fi ttings. Always provide a union so that
gas lines can be easily disconnected for servicing.
Flare nuts for copper lines and fl ex connectors are
usually considered to meet this requirement.
NOTE: A shutoff / dante valve should be sup-
plied in or near the unit (or as per local codes)
for ease of servicing this appliance.
IMPORTANT: Always check for gas leaks with
a soap and water solution or gas leak detector.
Do not use open fl ame for leak testing.
PLATEAU
®
SERIES-NG1 SYSTEM
DATA
Max. Supply Pressure 14" WC (3.49 kpa)
Min. Supply Pressure 5" WC (1.25 kpa)
Manifold Pressure 3.5" WC (0.87 kpa)
Manifold Pressure -Low 1.6" WC (0.40 kpa)
Orifi ce Size #25 DMS
Minimum Input 30,000 Btu/h
(8.79 kW)
Maximum Input 50,000 Btu/h
(14.65 kW)
PLATEAU
®
SERIES-LP1 SYSTEM
DATA
Max. Supply Pressure 14" WC (3.49 kpa)
Min. Supply Pressure 11" WC (2.73 kpa)
Manifold Pressure 10" WC (2.49 kpa)
Manifold Pressure-Low 6.4" WC (1.59 kpa)
Orifi ce Size #45 DMS
Minimum Input 38,000 Btu/h
(11.13 kW)
Maximum Input 49,000 Btu/h
(14.36 kW)
Note: If you have an incorrect fl ame pattern,
contact your Regency
®
dealer for further
instructions.
Incorrect fl ame pattern will have small, probably
yellow fl ames, not coming into proper contact
with the rear burner or fl ame sensor.
Burner
Flame Sensor
Pilot
Ignitor
PILOT ADJUSTMENT
Periodically check the pilot fl ames. Correct fl ame
pattern has two strong blue fl ames: 1 fl owing
around the fl ame sensor and 1 fl owing across
the burner (it does not have to be touching the
burner).
886 S.I.T. VALVE
DESCRIPTION
1) Manual high/low adjustment
2) Pilot adjustment
3) Outlet Pressure Tap
4) Inlet Pressure Tap
5) Pilot Outlet
6) Main Gas Outlet
7) Main Gas Inlet
1
3
2
4
5
6
7
Regency Plateau
®
Series Outdoor Gas Fireplace
13
INSTALLATION
WIRING DIAGRAM
This appliance does not require a 120V A.C. supply for operation.
0.886.001
Proflame Valve
Standard Main On/Off Switch
or Optional Wall Switch
Important: The AA batteries in the battery pack operate the burner switch. If the batteries become weak they will need to be replaced with quality alka-
line batteries. This unit will not operate without AA batteries.
14
Regency Plateau
®
Series Outdoor Gas Fireplace
INSTALLATION
CASTER INSTALLATION
Nutsert
Allen key
2. Line up mounting plate at each corner on bottom of unit.
Secure with three self tapping screws in locations shown below.
4. Retrofi t - Thread bolt into nutsert, hand tighten and fi nish tightening
bolt with supplied allen key.
If not a retrofi t install, position caster through hole - secure
caster with lock washer and lock nut.
5. After installation, lock out all 4 casters before assembling unit.
Caster location retrofi t and new
Screw locations
Screw location
Caster location (retrofi t) - Use Nutsert
Caster location (new) - Use bolt / lock washer / nut
Screw locations
Screw location
1. Install mounting plates onto bottom of Coffee Table or Island Plateau unit.
Use diagrams below to determine orientation of the plates and locations for screws and casters.
Note: there are different caster locations for the Island unit depending on whether the casters are being retrofi tted or not.
Coffee Table mounting plate confi gurations
IslandTable mounting plate
confi gurations
3. Line up caster with existing nutsert (retrofi t) or corresponding
hole ( see above diagrams) on plate.
Bottom of Plateau Unit Bottom of Island Unit
NOTE: Casters to be installed to the bottom of the unit frame before the unit is assembled.
Remove side and end panels - place on a soft clean surface.
Regency Plateau
®
Series Outdoor Gas Fireplace
15
INSTALLATION
1) Remove end panel (end with the ON/OFF switch). Panels are held in place
by magnets. Place panel on a soft clean surface.
2) Remove long side panel (left panel if you are facing end with ON/OFF
switch) to access the 3/8" fi tting to the gas control.
3) Connect gas line..
GAS CONNECTION
4) Check all gas connections (both valve train & propane tank or NG
source) under normal operating pressure, for leaks, with soapy water.
NOTE: If soap bubbles, this would indicate a gas leak.
5) Reverse steps 1 & 2.
Gas connection
@ unit
Average LP Tank Burn Times
High Low
20lb Tank 8 Hrs 10 Hrs
11lb Tank 3.5 Hrs 4 Hrs
16
Regency Plateau
®
Series Outdoor Gas Fireplace
INSTALLATION
CONVERSION FROM NG TO LP
1) Shut off the gas and allow unit to cool to room temperature.
3) Slide the burner to the left, away from the pilot assembly and lift out.
THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER
IF IN DOUBT DO NOT DO THIS CONVERSION !!
Each Kit contains one LP Conversion Kit
Conversion Kit # 376-972 Contains:
Qty. Part # Description
1 904-655 Burner Orifi ce #45
1 904-529 5/32" Allen Key
1 910-101 LP pilot orifi ce
1 918-590 Decal "Converted
to LPG"
1 908-528 Red "LP" label
1 911-009 Hi/Lo conversion LP For 886
1 911-089 Propane Hose & Regulator 48 in.
1 919-000 Instruction Sheet
Pilot Cap
Burner orifi ce
5) Pull off the pilot cap to expose the pilot orifi ce. Using a 5/32" allen key,
remove pilot orifi ce and replace with LP pilot orifi ce.
4) Remove burner orifi ce with a 1/2" wrench. Use another wrench to hold on
to the elbow behind the orifi ce. Discard orifi ce.
2) Remove burner buy removing 6 screws in locations shown below. If glass
crystals are installed, move the crystals out of the way to reveal screws.
6) Re-install pilot cap.
7) Reinstall burner assembly.
8) Adjust aeration accordingly.- see aeration adjustment section manual for
details.
Regency Plateau
®
Series Outdoor Gas Fireplace
17
INSTALLATION
10) Remove two screws to remove valve cover panel.
12) Attach the label “This unit has been converted to LPG” near or on top of
the serial # decal.
13) Replace yellow “NG” label with red “LPG” label.
11) Remove Hi/Lo pressure regulator by removing 2 screws as shown below.
Reverse steps to install LP pressure regulator.
HI/LO pressure
regulator
9) Remove end panel (panel w/ switch) from unit.
Gas connection
@ unit
14) Remove NG gas line, if installed - replace with LP regulator and quick
connection.
15) Check all gas connections (both valve train & LP tank) under normal
operating pressure, for leaks, with soapy water.
NOTE: If soap bubbles, this would indicate a gas leak.
16) Install LP tank (see LP tank installation in this manual).
17) Check inlet and outlet pressures.
18) Check operation of fl ame control.
18
Regency Plateau
®
Series Outdoor Gas Fireplace
INSTALLATION
LP TANK INSTALLATION - PTO30CFT ONLY
Gas connection
@ tank
NOTE: Max. tank size 11lb.
1) Remove end panel (opposite end of switch panel),.
2) Remove long side panel (left panel if facing ON/OFF switch end), to ac-
cess the 3/8" fi tting to the gas control.
3) Loosen butterfl y bolt to allow LP tank to be seated on the holder.
4) Seat tank on tray and tighten butterfl y bolt to secure tank to tray.
5) Connect the LP regulator quick connect to the tank.
7) Check all gas connections (both valve train & LP tank) under normal
operating pressure, for leaks, with soapy water.
NOTE: If soap bubbles, this would indicate a gas leak.
919-031
WARNING!
When using a LP tank - a minimum 1”(25mm) gap
at all times, between the floor and base of unit.
(Refer to owners manual)
must be maintained
IMPORTANT:
PTO30 CFT (Coffee table only)
To avoid tank pressure regulator freezing - when using an 11LB LP tank,
it is recommended the appliance is run on low (turned down 30%).
Regency Plateau
®
Series Outdoor Gas Fireplace
19
INSTALLATION
LP TANK REMOVAL
LP TANK INSTALLATION
PTO30IST/PTO30CKT ONLY
2) Ensure tank is fully closed. Disconnect gas line.
3) Slide out LP gas tank by pulling from handle on slide out tray.
NOTE: DO NOT SLIDE OUT TANK BY GRASPING FROM TOP OF TANK.
4) Undo butterfl y bolt to release tank.
5) Refi ll tank and reinstall by reversing steps.
Butterfl y bolt
Butterfl y bolt
Slide out handle
1) Remove end panel (opposite end of switch panel).
1) Remove end panel (opposite end of switch panel).
2) Slide out LP gas tank by pulling from handle on slide out tray.
3) Undo butterfl y bolt to allow LP tank to be seated on the holder.
4) Place LP tank onto slide out try and screw in butterfl y bolt to secure
tank.
5) Push tank in from the bottom.
DO NOT PUSH IN FROM THE TOP OF THE TANK.
6) Connect the LP regulator quick connect to the tank
7) Check all gas connections (both valve train & propane tank) under nor-
mal operating pressure, for leaks, with soapy water.
NOTE: If soap bubbles, this would indicate a gas leak.
919-031
WARNING!
When using a LP tank - a minimum 1”(25mm) gap
at all times, between the floor and base of unit.
(Refer to owners manual)
must be maintained
Gas connection
@ tank
NOTE: Max tank size 20lb.
20
Regency Plateau
®
Series Outdoor Gas Fireplace
INSTALLATION
1) Remove the end panel (side with switch assembly mounted on it) from unit.
2) Connect 2 wires to the switch - position switch in OFF position.
3) Replace panel.
BATTERY INSTALLSWITCH CONNECTION
3) Install 4 - AA batteries and reverse steps.
Battery compartment
1) Remove left side (with switch assembly) end panel from unit.
2) Slide out battery compartment - located below the DFC panel.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Regency Fireplace Products Plateau PTO30CKT Owner's manual

Brand
Regency Fireplace Products
Model
Plateau PTO30CKT
Category
Fireplaces
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents