Cerio ANT-10AO Installation guide

Brand
Cerio
Model
ANT-10AO
Category
Flat panel wall mounts
Type
Installation guide
Installation Guide
5GHz 2x2 Outdoor Omni 10dBi with 1M N-Plug to SMA-Plug NFC200 Low Loss RF Cables Pole/Wall Mount Antenna
1
CERIO Corporation
ANT-10AO
5GHz 2x2 Outdoor Omni 10dBi
with RF Cables Pole/Wall Mount Antenna
Installation Guide
Technical Support
E-mail: support@cerio.com.tw
TEL: +886-2-8911-6160 #222
Web Site: www.cerio.com.tw
Installation Guide
5GHz 2x2 Outdoor Omni 10dBi with 1M N-Plug to SMA-Plug NFC200 Low Loss RF Cables Pole/Wall Mount Antenna
2
Package Contents :
ANT-10AO Main Unit x1
Adjustable Pole & Wall Mounting Kit x1
RF Cables (NFC-NSP-1M) x2
Quick Installation Guide x1
Warranty Card x1
Main Unit Overview : (ANT-10AO)
RF Cable Overview : (NFC-NSP-1M)
2x2 SMA Connect
2x2 SMA Connect
Installation Guide
5GHz 2x2 Outdoor Omni 10dBi with 1M N-Plug to SMA-Plug NFC200 Low Loss RF Cables Pole/Wall Mount Antenna
3
Installation:
1. Mount the antenna on the brackets according to the Mounting diagram. Make sure
the horizontal omnidirectional of the ANT-10AO antenna with a beamwidth (H plane)
of 360 ̊ , a beamwidth (E plane) of 15 ̊and downtilt of 15 ̊.
2. Mount the ANT-10AO antenna on the antenna on the mast supplied by customer
according to the Mounting diagram.
3. Test the antenna with equipment to make sure the antenna receive the best signal first,
then lock all the screws and seal the connector between ANT-10AO antenna and NFC-NSP-
1M RF cables with a waterproof cap.
No Surge arrester installation
Installation using a Surge arrester
Installation Guide
5GHz 2x2 Outdoor Omni 10dBi with 1M N-Plug to SMA-Plug NFC200 Low Loss RF Cables Pole/Wall Mount Antenna
4
NO
DESCRIPTION
QTY
NO
DESCRIPTION
QTY
1
L-Bracket
1
6
M4 flat washer
4
2
4
＂
Hose Clamps
2
7
M6 flat washer
6
3
U-bolt
2
8
M6 spring washer
6
4
Plastic wall plug
4
9
M6 wing nuts
4
5
5/32" Self tapping screws
4
10
M6 machine screws
2
1. Pole Mount
⑵
To fix the Antenna on
the L-Bracket：
⑶
It’s available to the horizontal
pole without change the L-Bracket
orientation.：
2. Pole Mount
Pole O-Clamps: Pole Range Ø51-Ø102mm(2.0”〜4.0”)
Caution:
The antenna radiation would be
interfered if the metal pole and
antenna overlap too much.
Installation step:
①
→
②
→
③
→
④
① →②→③→④
① →②→③→④→⑤
3. Alternative wall mount
Drill 4 holes on the wall with following dimensions.
⑴
Installation step
：
Pole U-bolt: Pole Range Ø38-Ø102mm(1.5”〜4.0”)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Cerio ANT-10AO Installation guide

Brand
Cerio
Model
ANT-10AO
Category
Flat panel wall mounts
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents