urban ambiance UQL2520 Installation guide

Brand
urban ambiance
Model
UQL2520
Type
Installation guide
Package Contents
1of2
B
Fixture
Body
x1
C
A
Spacer
Tube
x1
D
Check
Ring
x1
Crossbar Assembly
x1
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (3)A19 Medium Base 100W Maximum,Alternate bulb (3) 23W CFL
Estimated Assembly Time: 20-30 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
E
Nipple with
Hex Nut
x1
F
Flat
Washer
x2
G
Rubber
Washer
x2
H
I
J
Hex
Nut
x1 Cap
x1
Finial
x1
KDiffuser
x1
L
Crystal
Pendant
x44
STEP 1 Install Crossbar Assembly-
.
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Figure 1
Supply Wires with
Ground Wire
A
Outlet Box Screws
(not included)
Outlet Box
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
Mounting
Screw
A
Mounting
Ball
Ceiling
Canopy
STEP 4 Attach Fixture Body to
Mounting Screw
-
A. Remove Mounting Balls from the
Crossbar Assembly (A). Place the
Ceiling Canopy of the Fixture Body
(B) over the Mounting Screws and
secure with removed Mounting
Balls. Hand tighten until snug.
B
Figure 4
Step 2 Continued
Figure 2
STEP 2 Fit Ceiling Canopy to Crossbar Assembly-
A. Remove mounting balls from the Crossbar Assembly (AA). Fit the
Ceiling Canopy to the Crossbar Assembly (AA) and secure with
mounting balls. Note: The Ceiling Canopy should be snug against
the ceiling and the mounting balls. If Not, adjust the length of the
nipple on the Crossbar Assembly (AA) By unscrewing the
preassembled hex nut and lock washer and then screwing the
Mounting screws in or out of the crossbar until The correct length is
Achieved. Once the Ceiling Canopy is secure, remove the mounting
ball and Ceiling Canopy and proceed to Step 3.
Mounting
Screw
A
Mounting
Ball
Ceiling
Canopy
B
Hex Nut and
Lock Washer
STEP 5 Install Bulbs, Diffuser and Crystal Pendants-
A. Thread the hex nut end of the Nipple with Hex Nut (E) into the hex
coupling on the bottom center of the Fixture Body (B). By using
pliers, thread the hex nut against the hex coupling and hand tighten
until snug.
B. Pass the Spacer Tube (C), the Check Ring (D), Flat Washers (F),
Rubber Washers (G) and Diffuser (K) over the end of the Nipple (E)
as shown. Secure by threading the Hex Nut (H) onto the Nipple (E).
Tighten until snug. Note: the Sandblast side of Diffuser should up.
1pc Crystal Pendant
spare part provided
Installation Instructions: UQL2520
www.urbanambiance.com
2of2
SKU: UQL2520
15.25” Dia.
11.25”
6.75”
6”Dia.
PART NUMBER
NO. PART NUMBER REPLACEMENT PART REQ.
UQL2520DIDIFFUSER 11
(3) 100W
Bulbs
(Not Supplied)
Medium
Base UQL2520CR CRYSTAL 442
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/4"
1
2
B
Ring
Socket Bulb (not
included)
E
C
F
L
F
D
G
G
H
I
J
K
Figure 4
Step 5 Continued
C. Pass the Cap (I) over the
end of the Nipple (E) and
secure with the Finial
(J).
D. Attach Crystal Pendants
(L) to the Ring.
E. This fixture uses standard
bulbs with standard screw
base. Maximum 100 watts.
Insert bulb and screw
snugly into place.
Your fixture is now
assembled and ready to
use. Enjoy!
www.urbanambiance.com
  • Page 1 1
  • Page 2 2

urban ambiance UQL2520 Installation guide

Brand
urban ambiance
Model
UQL2520
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents