Vmac H400011 Owner's manual

www.vmacair.com

Hydraulic Driven Air Compressor

Installation and Owner’s Manual

(Includes Service Instructions)

®

H400011 | H600011

Closed Center Hydraulic Systems

VMAC - Vehicle Mounted Air Compressors

VMAC Technical Support: 888-241-2289

VMAC Knowledge Base: kb.vmacair.com

1

Table of Contents

General Information .................................................3

Safety ..............................................................4

Safety Precautions ..................................................5

Warranty ...........................................................8

Hydraulic Driven Air Compressor Installation Manual ........... 11

Installation Considerations .........................................13

Mounting Locations and Ventilation ................................14

Speed Control .....................................................16

Hydraulic Requirements ............................................ 17

Hydraulic Fluid and Line Sizing Recommendations ..................19

Hydraulic Driven Air Compressor Harness Reference ............... 22

Upﬁtter Electrical Requirements ................................... 24

Installing the Hydraulic Driven Air Compressor System ............. 26

Telematics integration..............................................27

Testing the Installation ............................................ 28

Performance Testing and System Adjustments ..................... 30

Hydraulic Driven Air Compressor Owner’s Manual ..............33

Identifying Your System ........................................... 35

System Components and Speciﬁcations ........................... 36

Display Box Operation ............................................ 43

Menus and System Adjustments ................................... 46

Menu Layout .......................................................47

System Operation (What to Expect at Start Up) ................... 50

Cold or Hot Weather Operation ................................... 53

Limp Mode ....................................................... 54

General Maintenance Information ................................. 55

Maintenance and Repair Safety ................................... 57

Service Reminders ................................................ 59

Regular Inspection Instructions .................................... 60

500 Hour / 1 Year Service ......................................... 64

Diagnostics and Troubleshooting ...................................71

Hydraulic Testing ..................................................81

Air Receiver Tank.................................................. 85

Recommended Accessories ....................................... 86

Accessory Products from VMAC ....................................87

Error Logs ........................................................ 90

Warranty Registration ............................................. 92

VMAC - Vehicle Mounted Air Compressors

VMAC Technical Support: 888-241-2289

VMAC Knowledge Base: kb.vmacair.com

2

Document: 1930468

Changes and Revisions

Revision Revision Details Revised by

Checked by

Implemented

Eng. Tech. Qual.

Mech. Elec.

AInitial release. MSP GJM CAB MSP LPH 03 Mar. 2023

Additional Application Information

This manual applies to: H400011, and H600011.

• Compatible with “load sensing” variable displacement pumps.

Registered Trademarks

All trademarks mentioned in this manual are the property of their respective

owners. VMAC’s use of manufacturers’ trademarks in this manual is for

identification of the products only and does not imply any affiliation to, or

endorsement of said companies.

Loctite®, Loctite® 242 and Loctite® 567 are registered trademarks of Henkel AG &

Company KGaA.

Eaton Aeroquip® is a registered trademark of EATON AEROQUIP INC.

Viton® is a registered trademark of The Chemours Company.

Notice

materials are provided by VMAC for informational purposes only, without

representation or warranty of any kind, and VMAC shall not be liable for errors

or omissions with respect to the materials. The only warranties for VMAC

products and services are those set forth in the express warranty statements

accompanying such products and services, if any, and nothing herein shall be

construed as constituting an additional warranty. Printing or copying of any page

in this document in whole or in part is only permitted for personal use. All other

use, copying or reproduction in both print and electronic form of any part of this

document without the written consent of VMAC is prohibited. The information

contained herein may be changed without prior notice.

Printed in Canada

Important Information

The information in this manual is intended for certified VMAC installers who

have been trained in installation and service procedures and/or for anyone with

mechanical trade certification who has the tools and equipment to properly and

safely perform the installation or service. Do not attempt installation or service

without the appropriate mechanical training, knowledge and experience.

Follow all safety precautions. Any fabrication for correct fit in modified vehicles

must follow industry standard “best practices”.

VMAC - Vehicle Mounted Air Compressors

VMAC Technical Support: 888-241-2289

VMAC Knowledge Base: kb.vmacair.com

3

Introduction

This manual provides operating instructions, specifications, adjustment,

maintenance and warranty information for the VMAC Hydraulic Driven Air

Compressor systems. Read this manual prior to servicing or operating the

compressor system.

Follow all safety precautions when servicing or operating the VMAC system as

moving fan blades and other rotating components pose an extreme hazard.

Proper service and repair are important to the safety of the operator and the safe,

reliable operation of the equipment. Always use genuine VMAC replacement parts.

The procedures described in this manual are the only approved methods of service

and operation.

Ordering Parts

To order parts, contact a VMAC dealer. The dealer will ask for the VMAC System ID

(see page 35), part number, description and quantity. Locate the nearest dealer

online at www.vmacair.com/dealer-locator or call 1-877-912-6605.

General Information

Additional Support

Additional resources such as installation manuals, illustrated parts lists, the VMAC

Knowledge Base, air tool consumption guides, etc. are available at

https://www.vmacair.com/support/.

VMAC is unable to provide hydraulic circuit designs or consult on

specific hydraulic installations. We recommend working with a local

hydraulic expert to design and/or install the hydraulic circuit that

will power the Hydraulic Driven Air Compressor system.

VMAC - Vehicle Mounted Air Compressors

VMAC Technical Support: 888-241-2289

VMAC Knowledge Base: kb.vmacair.com

4

This symbol is used to call attention to instructions concerning

personal safety. Watch for this symbol; it points out important

safety precautions, it means, “Attention, become alert! Your personal

safety is involved”. Read the message that follows and be aware

of the possibility of personal injury or death. As it is impossible

to warn of every conceivable hazard, common sense and industry

standard safety practices must be observed.

This symbol is used to call attention to instructions on a specific

procedure that if not followed may damage or reduce the useful life

of the compressor or other equipment.

This symbol is used to call attention to additional instructions or

special emphasis on a specific procedure.

Safety

Important Safety Notice

The information contained in this manual is based on sound engineering principles,

research, extensive field experience and technical information. Information

is constantly changing with the addition of new models, assemblies, service

techniques and running OEM changes. If a discrepancy is found in this manual,

contact VMAC Technical Support prior to initiating or proceeding with installation,

service or repair. Current information may clarify the issue. Anyone with knowledge

of such discrepancies, who proceeds to perform service and repair, assumes all

risks.

Only proven service procedures are recommended. Anyone who departs from the

specific instructions provided in this manual must first ensure that their safety and

that of others is not being compromised, and that there will be no adverse effects

on the operational safety or performance of the equipment.

VMAC will not be held responsible for any liability, consequential damages, injuries,

loss or damage to individuals or to equipment as a result of the failure of anyone

to properly adhere to the procedures set out in this manual or standard safety

practices.

Safety should be the first consideration when performing any service operations.

If there are any questions concerning the procedures in this manual, or more

information is required, please contact VMAC Technical Support prior to beginning

work.

Safety Messages

This manual contains various warnings, cautions and notices that must be

observed to reduce the risk of personal injury during installation, service or repair

and the possibility that improper installation, service or repair may damage the

equipment or render it unsafe.

VMAC - Vehicle Mounted Air Compressors

VMAC Technical Support: 888-241-2289

VMAC Knowledge Base: kb.vmacair.com

5

Burn Hazard

• The compressor system gets very hot during operation, contact

with the components or the oil can cause serious injury. Allow

sufficient time for the system to cool before performing service.

• Never allow any part of your body to contact the compressor

components.

Personal Safety

• Do not breathe the compressor air. Vaporized oil is a respiratory

hazard.

• Always use the appropriate personal protective equipment,

particularly eye and hearing protection when operating air powered

equipment.

As it is impossible to warn of every possible hazard that may result

from operating this system, common sense and industry standard

safety practices must be observed.

Read this information before operating the compressor for the first time. Follow the

information and procedures in this manual for operation, maintenance and repair.

Observe the following items to reduce the chance of personal injury or equipment

damage.

Follow all safety precautions for mechanical work. Moving belts and rotating

components are an extreme hazard. Stay clear of all moving parts when the system

is operating. Only qualified personnel should perform maintenance and repair on

system components and only while the system is properly shut down.

Proper service and repair are important to the safety of the service technician

and the safe, reliable operation of the equipment. Always use genuine VMAC

replacement parts.

The procedures described in this service manual are effective methods of service

and repair. Some procedures may require the use of tools specially designed for a

specific purpose. Anyone using a replacement part, service procedure or tool must

first determine that neither their safety nor the safe operation of the equipment

will be compromised by the replacement part, service procedure or tool selected.

Safety Precautions

VMAC - Vehicle Mounted Air Compressors

VMAC Technical Support: 888-241-2289

VMAC Knowledge Base: kb.vmacair.com

6

Fire and Explosion Hazard

• Vaporized oil propelled by high pressure air is an explosive mixture.

• Fire in the compressor can cause an explosion and flame projection.

Should this occur, there is potential for serious injury or death.

• Operate the compressor in a well ventilated area free of flammable

vapors, dust, or other combustible materials.

• Never place objects against or on top of the compressor.

• Never expose the Air Oil Separator Tank or compressor to extreme

heat.

Compressor Air and Oil Hazard

• The compressor system is under sufficient pressure that a leak

could force the air/oil mixture through the skin directly into your

bloodstream. This could cause serious injury or death.

• Ensure the system is completely depressurized before attempting

maintenance or repair.

• Do not use compressed air to clean off clothing or skin, compressed

air can penetrate the skin causing serious injury or death.

• Do not move or service the compressor while it is pressurized or

operating.

• Do not move the compressor by pulling on any hoses.

• Components and hoses under pressure could separate suddenly, fly

out and cause serious injury or death. If equipped, the air receiver

tank must be drained before servicing any components in the

compressor system.

• Never adjust or attempt to make any repairs to the system while

the engine is running. Components and hoses under pressure could

fail and cause serious injury or death.

Burst Hazard

• Serious injury or death may result from an air tank explosion.

• Never exceed manufacturer’s maximum air pressure rating.

• Do not repair components, only replace with approved parts.

• Do not tamper with or disable factory safety equipment.

Moving Parts Hazard

• Before performing service, disconnect the negative battery cable

and the spark plug wire to prevent unexpected engine start.

• Do not operate the compressor without guards in place. If the

guards are damaged or missing, replace them before operating the

equipment.

VMAC - Vehicle Mounted Air Compressors

VMAC Technical Support: 888-241-2289

VMAC Knowledge Base: kb.vmacair.com

7

General Warnings

• Ensure the compressor and hydraulic system are cool and

depressurized prior to servicing.

• Be attentive for unexplained changes in operation parameters and

record any changes.

• Check the compressor oil level and condition before starting the

system. Do not add or change oil while the system is running. Use

only approved oil.

• The compressor may operate anytime the hydraulic circuit is

energized. Avoid contact with the compressor, hoses, or motor

during operation.

• Keep hoses and wiring away from hot, sharp, or moving

components.

• Use only approved hoses and replacement parts.

• Do not modify the equipment.

• Do not operate the air compressor when fatigued or under the

influence of alcohol or drugs.

• Know how to operate the compressor, fully read the manual.

• Check equipment before every use.

• Never bypass or disable any of the safety equipment.

• Never adjust or attempt to make any repairs to the compressor

system while the hydraulic circuit is pressurized. Components and

hoses under pressure could fail and cause serious injury or death.

VMAC - Vehicle Mounted Air Compressors

VMAC Technical Support: 888-241-2289

VMAC Knowledge Base: kb.vmacair.com

8

VMAC Standard Warranty (Limited)

For complete warranty information, including both VMAC Standard

Warranty (Limited) and VMAC Lifetime Warranty (Limited)

requirements, please refer to our current published warranty located

at: www.vmacair.com/warranty

If you do not have access to a computer, please contact us and we will

be happy to send you our warranty.

VMAC’s warranty is subject to change without notice.

VMAC Lifetime Warranty (Limited)

A VMAC Lifetime Limited Warranty is offered

on the base air compressor only and only on

UNDERHOOD, Hydraulic Driven, Transmission

Mounted, Gas and Diesel Engine Driven Air

Compressors, Multifunction Power Systems, and

other products as defined by VMAC, provided that

(i) the purchaser fully completes and submits a

warranty registration form within 3 months of purchase, or 200 hours of operation,

whichever occurs first; (ii) services are completed in accordance with the Owner’s

Manual; (iii) proof of purchase of applicable service kits are made available to

VMAC upon request.

The VMAC Lifetime Warranty is applicable to new products shipped on or after 1

October, 2015.

Warranty Registration

The VMAC warranty registration form is located near the back of this manual. This

warranty registration form must be completed and sent to VMAC at the time of

installation for any subsequent warranty claim to be considered valid.

There are 4 ways the warranty can be registered with VMAC:

www.vmacair.com/warranty

warranty@vmacair.com

(877) 740-3202

VMAC - Vehicle Mounted Air Compressors

1333 Kipp Road, Nanaimo, BC, Canada V9X 1R3

LIFETIME

A

I

R

I

N

O

V

A

T

E

D

T

R

U

S

T

S

E

R

V

I

C

E

V

A

L

U

E

WARRANTY

Warranty

VMAC - Vehicle Mounted Air Compressors

VMAC Technical Support: 888-241-2289

VMAC Knowledge Base: kb.vmacair.com

9

VMAC warranty work must be pre-authorized by VMAC. Claims are

processed via our dealer network. If you are not a VMAC dealer,

please select one to work with via our Dealer Locator:

https://www.vmacair.com/dealer-locator/

1) Communicate with VMAC Technical Support at 1-888-241-2289 or

tech@vmacair.com to help diagnose/troubleshoot the problem prior to repair.

VMAC technical support will require the VMAC System ID, and hours on the

compressor.

2) VMAC will provide direction for repair or replacement of the failed

components.

3) If requested, failed parts must be returned to VMAC for evaluation.

4) Dealers may login to the VMAC website to view the "VMAC Labour Time

Guide" (under “Agreements”) to see the allowable warranty labour times.

5) Warranty invoices must include the Service Ticket number, VMAC System ID#,

hours on the compressor, and a detailed description of the work performed.

6) VMAC Warranty does not cover consequential damages, overtime charges,

mileage, travel time, towing/recovery, cleaning or shop supplies.

7) Dealers submit warranty claims on behalf of the Vehicle Owner/End User

aﬀected by the defective part(s). The dealer ensures that all warranty credits

are refunded back to the Vehicle Owner/End User who made the initial

warranty claim.

VMAC Warranty Claim Process

In order to qualify for Lifetime Warranty (Limited), the completed

warranty registration form must be received by VMAC within 3

months of the buyer receiving the Product(s), or 200 hours of

operation, whichever occurs first.

If the completed warranty registration form has not been received

by VMAC within 3 months of the buyer receiving the Product(s),

or 200 hours of operation, the “Standard” warranty period will be

deemed to commence 30 days from the date of shipment from

VMAC.

Failure to follow the warranty claim process may result in denial of

the warranty claim.

VMAC Product Warranty Policies & Warranty Registration can be found on the

VMAC website (see previous page for URL).

Hydraulic Driven Air Compressor

Installation Manual

®

VMAC - Vehicle Mounted Air Compressors

VMAC Technical Support: 888-241-2289

VMAC Knowledge Base: kb.vmacair.com

13

Installation Considerations

Prior to installing the system, consider the following factors:

• For proper operation, VMAC’s Hydraulic Driven Air Compressor Systems require

proper hydraulic pressure and flow, ensure the hydraulic circuit is designed

with these requirements in mind (see page 17).

• See "Hydraulic Fluid and Line Sizing Recommendations" on page 19 for

additional hydraulic circuit recommendations.

• Is the intended location convenient for electrical, hydraulic, and air

connections?

• Will the intended location require extensive plumbing for the hydraulic system

or air hoses?

• Are the wire lengths, and air/hydraulic hose lengths as short as possible, and

with the least amount of 90° fittings possible?

• Can the oil level at the sight glass be checked easily?

• Can the unit be serviced easily?

• Will there be adequate clearance around the unit to provide good air

circulation and effective cooling (see page 14)?

• Will the unit be protected from excessive exposure to the elements?

• Will the unit be protected from incidental damage from other operations?

• Will the unit be mounted away from heat sources such as engines, exhaust, or

other components that can generate heat.

• Will the unit be mounted where it will be exposed to high contamination levels,

including combustible gases?

• If the intended mounting location is constructed of thin gauge material,

consider using the VMAC Mounting Brackets (P/N: A700140).

The information in this section is critical to ensure proper operation

of the system. Read these requirements prior to beginning the

installation.

Failure to adhere to these recommendations will cause the Hydraulic

Driven Air Compressor system to operate erratically.

The integrated cooler on the Hydraulic Driven Air Compressor

system is capable of removing all of the heat generated during air

compression from the compressor oil and hydraulic fluid.

Additional hydraulic oil cooling (such as VMAC’s Hydraulic Oil Cooler

(P/N: A850001) may be required for any other hydraulic equipment

is installed on the same circuit.

VMAC - Vehicle Mounted Air Compressors

VMAC Technical Support: 888-241-2289

VMAC Knowledge Base: kb.vmacair.com

14

Enclosed mounting is not recommended due to the significant heat

generated by the Hydraulic Driven Air Compressor.

While it is not possible to make absolute recommendations regarding ventilation

due to the widely differing circumstances that are possible, duty cycle, ambient

temperature and enclosure shape are some of the important variables that must be

considered.

Top Mounting

“Top mounted” is the preferred mounting location for the Hydraulic Driven Air

Compressor. Placing the unit on top of the service body provides the best access to

cool fresh air. Maintain a minimum of 6 in between the sides of the Hydraulic Driven

Air Compressor and all other solid objects (Figure 1).

Mounting Locations and Ventilation

Mounting the Hydraulic Driven Air Compressor in an enclosure will limit access

to cool fresh air, restrict the escape of hot air from around the unit and have an

adverse effect on cooling which may reduce the unit’s duty cycle. Ensure adequate

ventilation is provided for cooling and to evacuate the heat generated by the unit.

If mounting in an enclosure, VMAC strongly recommends mounting the unit on a

pullout drawer and extending the drawer any time the unit is run.

Figure 1 — Mounting locations

Enclosure mounted

(not recommended)

Top mounted

(Preferred)

Not recommended

VMAC does not recommend mounting the unit at the back of the

vehicle as the drag created when the vehicle is moving causes debris

to be deposited (and accumulated) inside the unit.

Significant ventilation and additional cooling will be required if the

Hydraulic Driven Air Compressor is mounted in the same enclosure

as the hydraulic oil reservoir. The heat generated during operation

will continue to heat the hydraulic fluid (even with fresh ambient air

entering the cooler).

Enclosed Mounting

VMAC - Vehicle Mounted Air Compressors

VMAC Technical Support: 888-241-2289

VMAC Knowledge Base: kb.vmacair.com

15

Recommended Component Layout

Figure 2 — Recommended component layout

Battery

Fuse

Ignition

switched

relay

Hydraulic

Driven Air

Compressor

Display Box

(mounted inside weather

proof enclosure)

VMAC - Vehicle Mounted Air Compressors

VMAC Technical Support: 888-241-2289

VMAC Knowledge Base: kb.vmacair.com

16

Speed Control

The Hydraulic Driven Air Compressor has the ability to signal for a higher engine

speed under high air demand conditions and for a lower engine speed under low

air demand conditions. A built in, electrically activated idle up system or an after-

market product is required to provide 2 speed operation.

The Hydraulic Driven Air Compressor is capable of constant operation at a fixed

engine speed and hydraulic pump gpm. There are several advantages to configuring

the system for 2 speed operation:

• Lower fuel consumption.

• Lower noise when air demand is low.

• Lower wear rates on the engine, hydraulic pump and compressor.

• Faster warm up during cold start weather.

The preferred approach for speed control is to restrict the hydraulic flow to the

Hydraulic Driven Air Compressor to the minimum requirement for the system

(8 – 9 gpm), this is desirable for cold climate start-up as it keeps hydraulic pressure

low during warm up.

The system must be at, or above, the minimum hydraulic flow before

starting the Hydraulic Driven Air Compressor.

Single Speed Operation (See Figure 3 on page 17 for “gpm vs cfm” chart)

When the system is activated, the Control Box in the Hydraulic Driven Air

Compressor will signal the PTO to increase hydraulic flow to provide the desired

cfm.

2 Speed Operation (See Figure 3 on page 17 for “gpm vs cfm” chart)

When the system is enabled, “Speed 1” is activated and the Control Box in the

Hydraulic Driven Air Compressor will signal the PTO to set hydraulic flow to the

minimum desired cfm.

“Speed 2” is activated to signal the PTO to increase hydraulic flow to provide the

maximum cfm (or speed system warm up).

VMAC - Vehicle Mounted Air Compressors

VMAC Technical Support: 888-241-2289

VMAC Knowledge Base: kb.vmacair.com

17

Hydraulic Requirements

While in operation, the required system pressure will vary between 1,500 psi and

2,800 psi.

The load sensing pressure compensated hydraulic pump must be rated for 3,000 psi

(maximum continuous) and 3,800 psi (maximum) to allow for an additional 200 psi

pressure drop in the pressure lines (external to the system) during startup with cold

hydraulic fluid.

H400011

The system must maintain hydraulic flow between 9 gpm and 14 gpm (Figure 3).

H600011

The system must maintain hydraulic flow between 14 gpm and 21 gpm (Figure 3).

Figure 3 — cfm vs gpm

VMAC is unable to provide hydraulic circuit designs or consult on

specific hydraulic installations. We recommend working with a local

hydraulic expert to design and/or install the hydraulic circuit that

will power the Hydraulic Driven Air Compressor system.

This VMAC Hydraulic Driven Air Compressor is designed to be driven

by a load sensing pressure compensated variable displacement

hydraulic pump.

H40

H60

VMAC - Vehicle Mounted Air Compressors

VMAC Technical Support: 888-241-2289

VMAC Knowledge Base: kb.vmacair.com

18

The stated hydraulic flow rates are nominal values only and may change due to

variations in hydraulic system efficiency, load, and flow. Tests should be performed to

confirm that the desired cfm has been achieved.

If the Hydraulic Driven Air Compressor system is being installed into an existing

hydraulic circuit, ensure the circuit meets the requirements listed in this chapter.

See "Hydraulic Fluid and Line Sizing Recommendations" on page 19 for additional

information.

An independent hydraulic system is recommended to simplify

installation, operation, and troubleshooting of the Hydraulic Driven

Air Compressor system.

If this system is being installed in a shared hydraulic circuit, the use

of a shut off valve is advised.

Page is loading ...

Vmac H400011 Owner's manual

This manual is also suitable for

Vmac H400011 Owner's manual

Related papers

Other documents