ESi Ergo Edge Monitor Arm Assembly Instructions

Brand: ESi Ergo

Model: Edge Monitor Arm

Category: Flat panel desk mounts

Type: Assembly Instructions

ASSEMBLY AND ADJUSTMENT

EDGE Model EDGE-SLV

Model EDGE-BLK

Model EDGE-WHT

MONITOR ARM

EDGE Rev A 2/17

PLEASE REVIEW these instructions before beginning the assembly and adjustment procedures. Check that

all the parts and tools listed below were provided with your order. Contact your supplier if any materials are

your satisfaction.

EDGE MONITOR ARM PARTS AND TOOLS

Base and Monitor Arm Assembly (1) Clamp Pad (1) Grommet Mount Plate (1)

Grommet Bar (1) Grommet Bolt (1)

M4x9M4x10M4x10

Grommet Bolt Washer (1)

M10x27

Grommet Bolt Nut (2)

VESA Plate Screw (4) VESA Locking Screw (1) 180° Locking Screw (1) 14mm Wrench (1)

2mm Allen Key (1) 4mm Allen Key (1) 5mm Allen Key (1)

PARTS AND TOOLS PROVIDED

CAUTION:

Hand-tighten screws only. Do not use power tools.

ADDITIONAL TOOLS REQUIRED

• Phillips screwdriver

3x 3

/8-16”

/16 x3/8-16

Clamp Method

The base assembly is shipped with the bottom clamp in the “upper attachment position.” To change to the

“lower attachment position” for thicker work surface, follow this procedure (see illustrations):

• Use the 4mm Allen key to remove the two screws holding the bottom clamp in position.

• Reattach the bottom clamp to the lower two holes. Tighten the screws securely using the Allen wrench.

CAUTION: Do not use a power drill. Clamp screws are rated at 102 in-lbs.

Attach Clamp Pad

• Peel the backing from the adhesive side of the clamp pad and adhere the pad

to the bottom of the base, as shown. The pad protects the work surface.

Install Base Assembly

• Clamp the base assembly to the work surface. Be sure to tighten the knob

securely.

• Proceed to “Monitor Installation” on page 5.

Two Base Assembly Attachment Methods

• Clamp method. The base assembly is clamped to

a table or desk surface that is between 0.6" (15mm)

thick and 3" (76mm) thick. See below.

• Grommet method. The base assembly is secured

through a grommet hole in the work surface, with

a diameter between 0.78" (20mm) and 2" (51mm).

Surface thickness must be between 0.6" (15mm)

and 1.5" (38.1mm). See page 4.

INSTALLATION OF BASE ASSEMBLY EDGE MONITOR ARM

Bottom

Clamp

Assembly

Upper Attachment

Position (Standard)

Lower Attachment

Position (Optional)

To Change: 1) Remove

Upper Attachment Screws

2) Re-Install Screws with

Clamp in Lower Position

Bottom

Clamp

Assembly

Remove

Re-Install

Upper

Attachment Lower

Attachment

1.38" – 3"

(35mm – 76mm)

0.6" – 2.2"

(15mm – 56mm)

Grommet

Method

Clamp

Method

Grommet

Method

Clamp

Method

Peel and

Adhere

Grommet Method

This method can be used for work surfaces that have a grommet hole in an

appropriate position. Surface thickness must be between 0.6" (15mm) and

1.5" (38.1mm), and the grommet hole diameter must be between 0.78" (20mm)

and 2" (51mm).

Remove Clamp Assembly

• Remove the standard clamp assembly from the base

assembly. Use the 4mm Allen key to remove the three

screws holding the clamp assembly in position. Retain

the three screws.

Attach Grommet Assembly

• Place the grommet bolt in the large center hole on the

grommet mount plate.

• With the grommet bolt in position, fasten the grommet

mount plate and bolt to the monitor arm base with the

three screws previously removed. As before, use the

4mm Allen key.

Attach Clamp Pad

• Peel the backing from the adhesive side of the clamp pad and adhere the

pad to the bottom of the grommet mount plate, as shown. The pad protects

the work surface.

Install Base Assembly

• Place the base assembly over the grommet hole, with the bolt centered.

• The bolt must extend under the work surface a minimum of 1.3" (33mm).

• Secure the base assembly as illustrated.

— Secure the grommet bar and washer with one of the grommet bolt nuts.

Use the provided wrench to tighten the nut securely.

—

• Proceed to “Monitor Installation” on page 5.

0.6" – 1.5"

(15mm – 38.1mm)

EDGE MONITOR ARM INSTALLATION OF BASE ASSEMBLY

Remove

Clamp

Assembly

Attach

Grommet

Assembly

Peel and

Adhere

Base

Assembly

Grommet

Bar

Washer

Nuts Wrench

MONITOR INSTALLATION EDGE MONITOR ARM

Attach Monitor to VESA Mount

• Remove the VESA plate from the VESA mount by pressing

down on the plastic tab to release the lock. Pull the plate

upward to remove.

Attach VESA Plate to Monitor

• Place the monitor face down on a at surface. Align

the VESA plate holes with the holes on the back of the

monitor. Attach the VESA plate using the four VESA

plate screws provided.

— There are two sets of four holes on the VESA plate.

One set has holes 3.9" (100mm) apart, the other

set has holes 3" (75mm) apart. Use the set that

matches the holes on the monitor.

Attach Monitor and VESA plate

• Slide the VESA plate (with monitor attached) back onto the VESA mount. Make sure the VESA plate clicks

securely in place.

— Optional: Install a VESA locking screw behind the VESA plate to prevent the tab on the VESA mount

from releasing the monitors.

VESA

Plate

Screw VESA Plate

3.9"

(100mm)

(75mm)

Monitor

(Face Down)

Upward

VESA

Plate 1.

VESA

Locking

Screw

(Optional)

Cable Management

Use the cable clip and cable cover to help manage the

monitor cables.

• Pinch the cable clip to remove it from the motion arm,

and again when re-installing it with the cables captured.

•

back in with the cables captured.

Tension Adjustments

1. Monitor swivel adjustment

— Use the 2mm Allen key to adjust the set screw for the desired ease of monitor rotation.

2. Motion arm swivel adjustment

— Use the 2mm Allen key to adjust the set screw for the desired ease of motion arm rotation.

3. Fixed arm swivel adjustment

— Use the 2mm Allen key

4. Monitor tilt adjustment

— Use the 4mm Allen key to adjust the set screw for the appropriate monitor weight.

5. Monitor arm weight adjustment

— Use the 5mm Allen key to adjust the set screw for the appropriate monitor weight.

— Weight capacity per arm is 6.5 lbs to 17.6 lbs (2.95 kg to 7.98 kg). Capacity may be reduced if monitor

size is greater than 26" (66cm) or depth is greater than 2.17" (55mm).

EDGE MONITOR ARM FINAL ADJUSTMENTS

Motion

Arm

Cable Cover

Cable

Clip

Fixed

Arm

Tension Adjustment

Behind

VESA

Plate

180° Lock-Out Feature

• Use the 2mm Allen key to secure the 180° locking screw into

the base assembly, below the xed arm. The locking screw

limits arm rotation to 180°. Fully tighten the screw, then back

out one full turn.

FINAL ADJUSTMENTS EDGE MONITOR ARM

Allen Key Storage

• Insert the Allen keys into the holes behind the VESA plate to store

for future adjustment.

— Insert the two smaller Allen keys into the same hole.

Store

Allen Keys

for Future

Adjustments

180°

Locking

Screw

800.833.3746 esiergo.com

ASSEMBLY AND ADJUSTMENT

EDGE-MAX

Model EDGE-MAX-SLV

MONITOR ARM

EDGE-MAX Rev A 2/17

PLEASE REVIEW these instructions before beginning the assembly and adjustment procedures. Check that

all the parts and tools listed below were provided with your order. Contact your supplier if any materials are

missing. Do not discard the packaging until satised that the product operates to your satisfaction.

EDGE-MAX MONITOR ARM PARTS AND TOOLS

Base and Monitor Arm Assembly (1) Clamp Pad (1) Grommet Mount Plate (1)

Grommet Bar (1) Grommet Bolt (1)

3x3

/8-16

Grommet Bolt Washer (1)

M10x27 9

/16x3/8-16

Grommet Bolt Nut (2)

Plastic Screw Cover (2)

4mm Allen Key (1)2.5mm Allen Key (1) 5mm Allen Key (1)

M5x8

VESA Plate Screw (4) 180° Locking Screw (1) 14mm Wrench (1)

PARTS AND TOOLS PROVIDED

CAUTION: Hand-tighten screws only. Do not use power tools.

M4x10

ADDITIONAL TOOLS REQUIRED

• Phillips screwdriver

Clamp Method

The base assembly is shipped with the bottom clamp in the “upper attachment position.” To change to the

“lower attachment position” for thicker work surface, follow this procedure (see illustrations):

• Use the 4mm Allen key to remove the four screws holding the bottom clamp in position.

• Reattach the bottom clamp to the lower four holes. Tighten the screws securely using the Allen wrench.

CAUTION: Do not use a power drill. Clamp screws are rated at 83 in-lbs.

Attach Clamp Pad

• Peel the backing from the adhesive side of the clamp pad and adhere the

pad to the bottom of the base, as shown. The pad protects the work surface.

Install Base Assembly

• Clamp the base assembly to the work surface. Be sure to tighten the knob

securely.

• Proceed to “Monitor Installation” on page 5.

Two Base and Monitor Arm Assembly Attachment Methods

• Clamp method. The base assembly is clamped to

a table or desk surface that is between 0.32" (8mm)

thick and 3.38" (86mm) thick. See below.

• Grommet method. The base assembly is secured

through a grommet hole in the work surface, with

a diameter between 0.78" (20mm) and 2" (51mm).

Surface thickness must be between 0.6" (15mm)

and 1.5" (38.1mm). See page 4.

INSTALLATION OF BASE ASSEMBLY EDGE-MAX MONITOR ARM

Grommet

Method

Clamp

Method

Grommet

Method

Clamp

Method

Bottom

Clamp

Assembly

Upper Attachment

Position (Standard)

Lower Attachment

Position (Optional)

To Change: 1) Remove

Four Screws

2) Re-Install Screws with

Clamp in Lower Position

Bottom

Clamp

Assembly

1.1" – 3.38"

(26mm – 86mm)

0.32" – 2.67"

(8mm – 68mm)

Remove

Upper

Attachment

Re-Install

Lower

Attachment

Peel and

Adhere

Grommet Method

This method can be used for work surfaces that have a grommet hole in an

appropriate position. Surface thickness must be between 0.6" (15mm) and

1.5" (38.1mm), and the grommet hole diameter must be between 0.78" (20mm)

and 2" (51mm).

Remove Clamp Assembly

• Remove the standard clamp assembly from the base

assembly. Use the 4mm Allen key to remove the four

screws holding the clamp assembly in position (two on

top, two on the bottom). Retain the four screws.

Attach Grommet Assembly

• Place the grommet bolt in the large center hole on

the grommet mount plate.

• With the grommet bolt in position, fasten the grommet

mount plate and bolt to the monitor arm base with

the four screws previously removed. As before, use the

4mm Allen key.

Attach Clamp Pad

• Peel the backing from the adhesive side of the clamp pad and adhere the

pad to the bottom of the grommet mount plate, as shown. The pad protects

the work surface.

Install Base Assembly

• Place the base assembly over the grommet hole, with the bolt centered.

• The bolt must extend under the work surface a minimum of 1.3" (33mm).

• Secure the base assembly as illustrated.

— Secure the grommet bar and washer with one of the grommet bolt nuts.

Use the provided wrench to tighten the nut securely.

—

• Proceed to “Monitor Installation” on page 5.

0.6" – 1.5"

(15mm – 38.1mm)

EDGE-MAX MONITOR ARM INSTALLATION OF BASE ASSEMBLY

Remove

Clamp

Assembly

Attach

Grommet

Assembly

Peel and

Adhere

Base

Assembly

Grommet

Bar

Washer

Nuts Wrench

MONITOR INSTALLATION EDGE-MAX MONITOR ARM

Attach Monitor to VESA Mount

• First remove the VESA plate from the VESA mount,

— Turn the knob on the back of the VESA mount

one-half turn counterclockwise.

— Pull the plate upward to remove.

Attach VESA Plate to Monitor

• Place the monitor face down on a at surface. Align

the VESA plate holes with the holes on the back of the

monitor. Attach the VESA plate using the four VESA

plate screws provided.

— There are two sets of four holes on the VESA plate.

One set has holes 3.9" (100mm) apart, the other

set has holes 3" (75mm) apart. Use the set that

matches the holes on the monitor.

Attach Monitor and VESA plate

• Slide the VESA plate (with monitor

attached) back onto the VESA

mount.

— Turn the knob on the back of

the VESA mount one-half turn

clockwise to secure the monitor

in place.

VESA

Plate

Screw VESA Plate

3.9"

(100mm)

(75mm)

Monitor

(Face Down)

Upward

Turn Knob

to Release

VESA Plate

Turn Knob

Clockwise

to Secure

Tension Adjustments

There are three possible swivel and tilt tension adjustments:

1. Monitor tilt adjustment

— Use the lever to adjust for the appropriate monitor weight — tighten for heavier monitors (clockwise)

and loosen for lighter monitors (counterclockwise).

2. Monitor arm weight adjustment

— Use the 5mm Allen key to adjust the set screw for the appropriate monitor weight.

— Weight capacity per arm is 17.6 lbs to 44 lbs (8 kg to 20 kg). Capacity may be reduced if monitor

size is greater than 26" (66cm) or depth is greater than 2" (51mm).

3. Monitor swivel adjustment

— Use the 2.5mm Allen key to adjust the set screw for the desired ease of motion rotation.

EDGE-MAX MONITOR ARM FINAL ADJUSTMENTS

Use

Lever to

Adjust

Cable Management

Use the cable clip and cable cover to help manage the

monitor cables.

• Pinch the cable clip to remove it from the motion

arm, and again when re-installing it with the cables

captured.

• Slide the cable cover out from the xed arm. Slide it

back in with the cables captured.

180° Lock-Out Feature

• Install the 180° locking screw in the base assembly to

limit the rotation of the xed arm.

— The lock-out feature allows 90° rotation toward the

user, but prevents 90° rotation away from the user.

— Install the 180° locking screw using the 2.5mm Allen

key. Fully tighten the screw, then back it out one full

turn.

Install Plastic Screw Covers

Two plastic screw covers are provided to cover the socket

screws on top of the base assembly.

• Press the screw covers in place over the socket screws.

FINAL ADJUSTMENTS EDGE-MAX MONITOR ARM

Motion

Arm

Cable Cover

Cable

Clip

Fixed

Arm

180°

Locking

Screw

Cover

800.833.3746 esiergo.com

ASSEMBLY AND ADJUSTMENT

EDGE2 Model EDGE2-SLV

Model EDGE2-BLK

Model EDGE2-WHT

DUAL MONITOR ARM

EDGE2 Rev A 2/17

PLEASE REVIEW these instructions before beginning the assembly and adjustment procedures. Check that

all the parts and tools listed below were provided with your order. Contact your supplier if any materials are

your satisfaction.

EDGE2 DUAL MONITOR ARM PARTS AND TOOLS

Base Assembly (1) Monitor Arm Assembly (2)

Clamp Pad (1) Grommet Mount Plate (1) Grommet Bar (1) Grommet Bolt (1)

Grommet Bolt Washer (1)

M10x27

Grommet Bolt Nut (2) 14mm Wrench (1)

2mm Allen Key (1) 4mm Allen Key (1) 5mm Allen Key (1)

M4x9M4x10M4x10

VESA Plate Screw (8) VESA Locking Screw (2) 180° Locking Screw (2)

PARTS AND TOOLS PROVIDED

CAUTION: Hand-tighten

screws only. Do not use

power tools.

ADDITIONAL TOOLS REQUIRED

• Phillips screwdriver

3x 3

/8-16

/16 x3/8-16

Peel and

Adhere

Clamp Method

The base assembly is shipped with the bottom clamp in the “upper attachment position.” To change to the

“lower attachment position” for thicker work surface, follow this procedure (see illustrations):

• Use the 4mm Allen key to remove the two screws holding the bottom clamp in position.

• Reattach the bottom clamp to the lower two holes. Tighten the screws securely using the Allen wrench.

CAUTION: Do not use a power drill. Clamp screws are rated at 102 in-lbs.

Attach Clamp Pad

• Peel the backing from the adhesive side of the clamp pad and adhere the pad

to the bottom of the base, as shown. The pad protects the work surface.

Install Base Assembly

• Clamp the base assembly to the work surface. Be sure to tighten the knob

securely.

• Proceed to “Install Monitor Arm Assemblies” on page 5.

Two Base Assembly Attachment Methods

• Clamp method. The base assembly is clamped to

a table or desk surface that is between 0.6" (15mm)

thick and 3" (76mm) thick. See below.

• Grommet method. The base assembly is secured

through a grommet hole in the work surface, with

a diameter between 0.78" (20mm) and 2" (51mm).

Surface thickness must be between 0.6" (15mm)

and 1.5" (38.1mm). See page 4.

INSTALLATION OF BASE ASSEMBLY EDGE2 DUAL MONITOR ARM

Bottom

Clamp

Assembly

Upper Attachment

Position (Standard)

Lower Attachment

Position (Optional)

To Change: 1) Remove

Upper Attachment Screws

2) Re-Install Screws with

Clamp in Lower Position

Bottom

Clamp

Assembly

Remove

Re-Install

Upper

Attachment Lower

Attachment

1.38" – 3"

(35mm – 76mm)

0.6" – 2.2"

(15mm – 56mm)

Grommet

Method

Clamp

Method

Grommet

Method

Clamp

Method

Grommet Method

This method can be used for work surfaces that have a grommet hole in an

appropriate position. Surface thickness must be between 0.6" (15mm) and

1.5" (38.1mm), and the grommet hole diameter must be between 0.78" (20mm)

and 2" (51mm).

Remove Clamp Assembly

• Remove the standard clamp assembly from the

base assembly. Use the 4mm Allen key to remove

the three screws holding the clamp assembly in

position. Retain the three screws.

Attach Grommet Assembly

• Place the grommet bolt in the large center hole on

the grommet mount plate.

• With the grommet bolt in position, fasten the

grommet mount plate and bolt to the monitor arm

base with the three screws previously removed. As

before, use the 4mm Allen key.

Attach Clamp Pad

• Peel the backing from the adhesive side of the clamp pad and adhere the

pad to the bottom of the grommet mount plate, as shown. The pad protects

the work surface.

Install Base Assembly

• Place the base assembly over the grommet hole, with the bolt centered.

• The bolt must extend under the work surface a minimum of 1.3" (33mm).

• Secure the base assembly as illustrated.

— Secure the grommet bar and washer with one of the grommet bolt nuts.

Use the provided wrench to tighten the nut securely.

—

assembly.

• Proceed to “Install Monitor Arm Assemblies” on page 5.

0.6" – 1.5"

(15mm – 38.1mm)

Remove

Clamp

Assembly

Attach

Grommet

Assembly

Peel and

Adhere

Base

Assembly

Grommet

Bar

Washer

Nuts Wrench

EDGE2 DUAL MONITOR ARM INSTALLATION OF BASE ASSEMBLY

Page is loading ...

ESi Ergo Edge Monitor Arm Assembly Instructions

Brand: ESi Ergo

Model: Edge Monitor Arm

Category: Flat panel desk mounts

Type: Assembly Instructions

Download PDF

report

ESi Ergo Edge Monitor Arm Assembly Instructions

ESi Ergo Edge Monitor Arm Assembly Instructions

Related papers

Other documents