Congratulations with your new Drip table, designed in
2021 by Hee Welling. We hope you will enjoy using this
product and follow these instructions to ensure correct
assembly. If you have any questions or comments,
please do not hesitate to contact us by mail on:
Drip HW
Hee Welling
2021
User instructions
Please read these instructions carefully and retain them
for future reference to ensure that the product is used
correctly. For your own safety, please study each step of
this instruction manual first. &Tradition is not responsible
for any faults or damages caused by not following these
instructions correctly. Do not modify this product in
any way.
Contents
A Table top x 2
B Legs x 6
C Corner Brackets x 4
D T-Bracket x 2
E Long frames x 4
F Short frames x 2
G Central Frame x 1
H Flat head hex screws x 28
I Short button screws x 36
J Long button screws x 12
K Allen key x 3
L End leg cover component x 4
M Centre leg cover component x2
Safety precautions
- Dispose of plastic bag from packaging and do not allow
children to play with it.
- The table is only intended for indoor use.
- Handle tabletop with care in order not to scratch surfaces.
- Two or more adults are required when lifting the table.
Drip HW
Hee Welling
2021
I J
A
B
D
C
E
FG
H
x28 x36 x12
K
L M
Cleaning instructions
Laminate can be cleaned with a soft cloth wrung in a mild
solution of lukewarm water and an universal cleaning
detergent. Always wipe with a dry soft cloth after clean-
ing. For difficult stains such as coffee or tea use a nylon
bristle brush with mild household cleaner or detergent,
rinsing with clean water and repeating as necessary. Rinse
thoroughly with water.
Aluminium (powder coated or polished) can be cleaned
using a soft cloth wrung in lukewarm water. Always dry im-
mediately with a soft cloth. Avoid use of abrasive cleaning
products such as steel wool as this will cause damage to the
surface.
Step 1
Fit the T-Bracket (D) and top section of the
leg together with x2 long button screws (J).
The x2 small holes on the T-Brackets (D)
must be facing upwards, see illustration.
Important: Make sure you tighten these
screws properly to ensure each leg is secure.
Step 2
Insert the T-Brackets (D) into both ends of
the central frame (G) as shown, and attach
them with a flat head hex screw (H).
Important: Do not completely tighten the
screws at this stage.
Step 3
Insert the x4 long frames (E) into each side
of the two T-Brackets (D) as shown, and
attach them with the flat head hex screws
(H).
Important: Do not completely tighten the
screws at this stage.
NB! Make sure the holes on the corner (C) are facing up.
Step 4
Insert the four corner brackets (C) into the
ends of the two short frames (F). Fasten with
the flat head hex screws (H). The 2 small
holes on the corners (C) must be facing
upwards, see illustration.
Important: Do not completely tighten the
screws at this stage.
Step 5
Place the leg-section (B) on the frame upside
down and allign all four legs in each corner
(C). Install two long button screws (J) in each
corner to connect them.
NB! Make sure the holes on
the corner (C) are facing up.
Step 6
Insert the installed short frames (F) into both
sets of long frames (E). Fasten with x4 flat
head hex screws (H) in each end.
Step 7
Place the cover components (M) on each of
the 6 leg brackets (C) and attach them with
screws (K).
Step 8
Place both tabletops (A) upside down on
a soft, flat surface, making sure that the
rounded corners are facing the ends. Then
place the frame on top, upside down. Use the
short button screws (I) to secure the top to
the frame.
Important: Only install the screws (I) slightly
and then finally tighten all of them to secure
correct fit.
Step 9
Finally, double check that all screws are tight
and secure. Then flip the table and enjoy your
product.
andtradition.com
/
