Sony SLV-SF900G User manual

filename[01GB02COV-NP0.fm] model name1[SLV-SF900G] model name2[]

[3-062-327-

11

(1)]

3-062-327-

11

(1)

Video Cassette

Recorder

Operating Instructions

The SmartFile function in this model meets the requirements of EU, EFTA,

Central and Eastern Europe

SLV-SF900G

PAL NTSC 4.43

Chlorine free paper

2

WARNING

filename[01GB03GET-NP0.fm] model name1[SLV-SF900G] model name2[]

[3-062-327-

11

(1)]

WARNING

To prevent fire or shock hazard, do not expose the

unit to rain or moisture.

To avoid electrical shock, do not open the cabinet.

Refer servicing to qualified personnel only.

Mains lead must only be changed at a qualified

service shop.

Notice for customers in the United

Kingdom

A moulded plug complying with BS1363 is fitted to

this equipment for your safety and convenience.

If the 13A fitted plug does not match the outlet

socket in your home, please refer to your Appointed

Sony Dealer for advice.

Should the fuse in the plug supplied need to be

replaced, a 5 AMP fuse approved by ASTA or BSI

to BS1362, (i.e., marked with

or

mark)

must be used.

If the plug supplied with this equipment has a

detachable fuse cover, be sure to attach the fuse

cover after you change the fuse. Never use the plug

without the fuse cover. If you should lose the fuse

cover, please contact your nearest Sony service

station.

Precautions

Safety

• This unit operates on 220 – 240 V AC, 50 Hz.

Check that the unit’s operating voltage is

identical with your local power supply.

• If anything falls into the cabinet, unplug the unit

and have it checked by qualified personnel before

operating it any further.

• The unit is not disconnected from the mains as

long as it is connected to the mains, even if the

unit itself has been turned off.

• Unplug the unit from the wall outlet if you do not

intend to use it for an extended period of time. To

disconnect the cord, pull it out by the plug, never

by the cord.

Installing

• Allow adequate air circulation to prevent internal

heat buildup.

• Do not place the unit on surfaces (rugs, blankets,

etc.) or near materials (curtains, draperies) that

may block the ventilation slots.

• Do not install the unit near heat sources such as

radiators or air ducts, or in a place subject to

direct sunlight, excessive dust, mechanical

vibration or shock.

• Do not install the unit in an inclined position. It is

designed to be operated in a horizontal position

only.

• Keep the unit and cassettes away from equipment

with strong magnets, such as microwave ovens or

large loudspeakers.

• Do not place heavy objects on the unit.

• If the unit is brought directly from a cold to a

warm location, moisture may condense inside the

VCR and cause damage to the video head and

tape. When you first install the unit, or when you

move it from a cold to a warm location, wait for

about three hours before operating the unit.

Caution

Television programmes, films, video tapes and other

materials may be copyrighted. Unauthorized

recording of such material may be contrary to the

provisions of the copyright laws. Also, use of this

recorder with cable television transmission may

require authorization from the cable television

transmitter and/or programme owner.

Compatible colour systems

This VCR is designed to record using the PAL

colour system and play back using the PAL and

NTSC 4.43 colour systems. Recording of video

sources based on other colour systems cannot be

guaranteed.

VIDEO Plus + is a registered trademark of Gemstar

Development Corporation. VIDEO Plus + system is

manufactured under license from Gemstar

Development Corporation.

SmartFile is a trademark of Sony Corporation.

ASA

3

Table of contents

Getting Started

filename[306232711SF900GTOC.fm] model name1[SLV-SE700G] model name2[SLV-SE700I]

model name3[SLV-SE800G] model name4[SLV-SE800I]

[3-062-327-

11

(1)]

Table of contents

Getting Started

4

Step 1 : Unpacking

5

Step 2 : Setting up the remote commander

9

Step 3 : Connecting the VCR

15

Step 4 : Tuning your TV to the VCR

18

Step 5 : Setting up the VCR with the Auto Set Up function

19

Step 6 : Setting the clock

24

Selecting a language

25

Presetting channels

28

Setting/changing the station names

30

Changing/disabling programme positions

34

Setting your personal code

Basic Operations

37

Playing a tape

40

Recording TV programmes

44

Recording TV programmes using the

VIDEO Plus + system

49

Setting the timer manually

Additional Operations

52

Playing/searching at various speeds

54

Setting the recording duration time

55

Synchronized Recording

57

Checking/changing/cancelling timer

settings

59

Recording stereo and bilingual

programmes

61

Searching using the index function

62

Adjusting the picture

64

Changing menu options

Editing

67

Connecting to a VCR or stereo

system

69

Basic Editing

SmartFile function

70

About the SmartFile function

72

Recording using the SmartFile

function

77

Selecting and playing a programme

78

Checking the contents of a tape

80

Labelling a recorded programme and

tape

88

Registering the contents of a

recorded tape in the SmartFile label

90

Protecting a recorded programme

92

Erasing the data of an unwanted

programme

Additional Information

94

Troubleshooting

100

Specifications

101

Index to parts and controls

106

Menu chart

Back cover

Index

4

Unpacking

filename[01GB04GET-NP0.fm] model name1[SLV-SF990G(ENG)] model name2[]

[3-062-324-

11

(1)]

Getting Started

Step 1 : Unpacking

Check that you have received the following items with the VCR :

• Remote commander

• R6 (size AA) batteries

• Aerial cable

• SmartFile labels

Getting Started

5

Setting up the remote commander

filename[01GB04GET-NP0.fm] model name1[SLV-SF990G(ENG)] model name2[]

[3-062-324-

11

(1)]

Step 2 : Setting up the remote commander

Inserting the batteries

Insert two R6 (size AA) batteries

by matching the + and – on the

batteries to the diagram inside the

battery compartment.

Insert the negative (–) end first,

then push in and down until the

positive (+) end clicks into

position.

Using the remote commander

You can use this remote

commander to operate this VCR

and a Sony TV. Buttons on the

remote commander marked with a

dot (

•

) can be used to operate your

Sony TV. If the TV does not have

the symbol near the remote

sensor, this remote commander

will not operate the TV.

123

g

Remote sensor

[TV]

/

[VIDEO ]

To operate Set

[TV]

/

[VIDEO]

to

the VCR

[VIDEO]

and point at the remote sensor on the VCR

a Sony TV

[TV]

and point at the remote sensor on the TV

continued

6

Setting up the remote commander

filename[01GB04GET-NP0.fm] model name1[SLV-SF990G(ENG)] model name2[]

[3-062-324-

11

(1)]

TV control buttons

To Press

Set the TV to standby mode

?

/

1

Select an input source: aerial in or line in

t

TV/VIDEO

Select the TV’s programme position Programme number buttons,

–/– –, PROG +/–

Adjust the TV’s volume

2

+/–

Switch to TV (Teletext off)

a

(TV)

Switch to Teletext

/

(Teletext)

123

456

789

0

Programme

number

buttons

WIDE

PROG +/–

c

/

C

?

/

1

AUDIO MONITOR

t

TV/VIDEO

2

+/–

/

FASTEXT buttons

–/– –

a

DISPLAY

Getting Started

7

Setting up the remote commander

filename[01GB04GET-NP0.fm] model name1[SLV-SF990G(ENG)] model name2[]

[3-062-324-

11

(1)]

Notes

• With normal use, the batteries should last about three to six months.

• If you do not use the remote commander for an extended period of time, remove the batteries

to avoid possible damage from battery leakage.

• Do not use a new battery with an old one together.

• Do not use different types of batteries together.

• Some buttons may not work with certain Sony TVs.

Controlling other TVs with the remote commander

The remote commander is preprogrammed to control non-Sony TVs. If your TV is

listed in the table below, set the appropriate manufacturer’s code number.

* These buttons may not work with all TVs.

Tip

• When you set your TV’s code number correctly while the TV is turned on, the TV turns off

automatically.

Select the sound AUDIO MONITOR

Use FASTEXT FASTEXT buttons

Call up the on-screen display

DISPLAY

Change the Teletext page

c

/

C

Switch to/from wide mode of a Sony wide TV (For other

manufactures’ wide TVs, see “Controlling other TVs with

the remote commander”.)

WIDE

To Press

1

Set TV/VIDEO at the top of the remote commander to TV.

2

Hold down

?

/

1

, and enter your TV’s code number(s) using the programme

number buttons.Then release

?

/

1

.

Now you can use the following TV control buttons to control your TV:

?

/

1

, TV/VIDEO, programme number buttons, –/– – (ten’s digit), PROG +/–,

2

+/–,

a

(TV),

/

(Teletext), FASTEXT buttons, WIDE

*

, MENU

*

,

M

*

/

m

*

/

<

*

/

,

*

, and OK

*

.

continued

8

Setting up the remote commander

filename[01GB04GET-NP0.fm] model name1[SLV-SF990G(ENG)] model name2[]

[3-062-324-

11

(1)]

Code numbers of controllable TVs

If more than one code number is listed, try entering them one at a time until you find

the one that works with your TV.

To switch to wide mode, see the footnotes below this table for the applicable code

numbers.

*1

Press WIDE to switch to the wide picture mode you want.

*2

Press WIDE, then press

2

+/– to select the wide picture mode you want.

*3

Press WIDE. The menu appears on the TV screen.Then, press

M

/

m

/

<

/

,

to select the wide picture you

want and press OK.

Notes

• If the TV uses a different remote control system from the one programmed to work with the VCR, you

cannot control your TV with the remote commander.

• If you enter a new code number, the code number previously entered will be erased.

• If you remove the batteries of the remote commander for more than a few minutes, the code number may

be reset to 01 (Sony). In this case, reset the appropriate code number.

Manufacturer Code number

Sony

01

*1

, 02

Akai 68

Blaupunkt 10

C.G.M 09

Ferguson 52

Goldstar 03, 04, 17

Grundig

10

*1

, 11

*1

Hitachi 24

ITT

15, 16, 69

*3

JVC 33

Loewe 45

Mivar 09

NEC 66

Nokia

15, 16, 69

*3

Panasonic

17

*1

, 49

Philips

06

*1

, 07

*1

, 08

*1

Saba 12, 13

Samsung 22, 23

Sanyo 25

Sharp 29

Thomson

43

*2

Toshiba 38

Manufacturer Code number

Getting Started

9

Connecting the VCR

filename[01GB04GET-NP0.fm] model name1[SLV-SF990G(ENG)] model name2[]

[3-062-324-

11

(1)]

Step 3 : Connecting the VCR

We recommend connecting your VCR to your TV using a Scart (EURO-

AV) cable. You must still connect your VCR to your TV with an aerial

cable as well.

If you use the Scart (EURO-AV) cable for connecting, you will improve

the picture and sound quality playback of your VCR and make the set up

easier.

• Connection to your TV with an aerial cable only, see page 12.

• Connection to your TV and Set-Top Box, see page 13.

Connection to your TV with a Scart (EURO-AV) connector

1

Disconnect the aerial cable from your

TV and connect it to AERIAL IN on

the rear panel of the VCR.

2

Connect AERIAL OUT of the VCR

and the aerial input of your TV using

the supplied aerial cable.

Mains lead

i

LINE-1

(TV)

AERIAL IN

Scart

(EURO-AV)

to mains

Aerial cable (supplied)

AERIAL OUT

: Signal flow

Scart (EURO-AV) cable

(not supplied)

AERIAL IN

AERIAL

ANTENNE

IN

ENTREE

OUT

SORTIE

AERIAL

ANTENNE

IN

ENTREE

OUT

SORTIE

continued

10

Connecting the VCR

filename[01GB04GET-NP0.fm] model name1[SLV-SF990G(ENG)] model name2[]

[3-062-324-

11

(1)]

Notes

• If the TV is connected to the LINE-1 (TV) connector, setting the RF channel to OFF is

recommended (see page 17). In the OFF position, only the signal from the aerial is output

through the AERIAL OUT connector.

• For a correct SmartLink connection, you will need a Scart cable which the 21 pins are

completely connected (for example a Sony cable reference VMC-2121HG). Please refer to

your TV’s instruction manual as well for this connection.

3

Connect LINE-1 (TV) on the VCR

and the Scart (EURO-AV) connector

on the TV with the optional EURO-

AV cable.

This connection improves picture and

sound quality.Whenever you want to

watch the VCR picture, press

t

TV/

VIDEO to display the VIDEO

indicator in the display window.

4

Connect the mains lead to the mains.

You can now tune your TV to the VCR (see page 15).

LIGNE-1

(

TV

)

LINE-1

(

TV

)

Getting Started

11

Connecting the VCR

filename[01GB04GET-NP0.fm] model name1[SLV-SF990G(ENG)] model name2[]

[3-062-324-

11

(1)]

About the SMARTLINK features

If the connected TV complies with

SMARTLINK, NexTView Link,

MEGALOGIC

*1

, EASYLINK/

CinemaLink

*2

, Q-Link

*3

or T-V

LINK

*4

, you can use the

SMARTLINK function after you complete the steps on the previous page (the SMARTLINK

indicator appears in the VCR’s display window when you turn on the TV).You can enjoy the

following SMARTLINK features.

• Preset Download

You can download your TV tuner preset data to this VCR and tune the VCR according to that

data in Auto Set Up. This greatly simplifies the Auto Set Up procedure. Be careful not to

disconnect the cables or exit the Auto Set Up function during the procedure.

See “Setting up the VCR with the Auto Set Up function” on page 18.

• TV Direct Rec

You can easily record what you are watching on the TV (other than tapes being played on this

VCR). For details, see “Recording what you are watching on the TV (TV Direct Rec)” on

page 43.

• One Touch Play

With One Touch Play, you can start playback automatically without turning on the TV. For

details, see “Starting playback automatically with one button (One Touch Play)” on page 39.

• One Touch Menu

You can turn on the VCR and TV, set the TV to the video channel, and display the VCR’s on-

screen display automatically by pressing MENU on the remote commander.

• One Touch Timer

You can turn on the VCR and TV, set the TV to the video channel, and display the timer

recording menu (the TIMER METHOD menu, the TIMER menu or the VIDEO Plus + menu)

automatically by pressing TIMER on the remote commander. You can set which timer

recording menu is displayed using TIMER OPTIONS in the OTHER OPTIONS menu (see

page 66).

• Automatic Power off

You can have the VCR turn off automatically, if the VCR is not used for about 1 minute, after

you turn off the TV.

• NexTView Download

You can easily set the timer by using the NexTView Download function on your TV. Please

refer to your TV’s instruction manual.

*1

“MEGALOGIC” is a registered trademark of Grundig Corporation.

*2

“EASYLINK/CinemaLink” is a trademark of Philips Corporation.

*3

“Q-Link” is a trademark of Panasonic Corporation.

*4

“T-V LINK” is a trademark of JVC Corporation.

Note

• Not all TVs respond to the functions above.

TV

STEREO

AUTO SET UP

SMH

LP

EP

SP

VIDEO

EDIT

NICAM

VPS

PDC

OPC

SMARTLINK

continued

12

Connecting the VCR

filename[01GB04GET-NP0.fm] model name1[SLV-SF990G(ENG)] model name2[]

[3-062-324-

11

(1)]

Connection to your TV with an aerial cable only

1

Disconnect the aerial cable from your

TV and connect it to AERIAL IN on

the rear panel of the VCR.

2

Connect AERIAL OUT of the VCR

and the aerial input of your TV using

the supplied aerial cable.

3

Connect the mains lead to the mains.

You can now tune your TV to the VCR (see page 15).

Mains lead

AERIAL IN

to mains

Aerial cable (supplied)

AERIAL OUT

: Signal flow

AERIAL IN

AERIAL

ANTENNE

IN

ENTREE

OUT

SORTIE

AERIAL

ANTENNE

IN

ENTREE

OUT

SORTIE

Getting Started

13

Connecting the VCR

filename[01GB04GET-NP0.fm] model name1[SLV-SF990G(ENG)] model name2[]

[3-062-324-

11

(1)]

Connection to your TV and Set-Top Box (STB)

If you don’t use a STB, skip to page 15.

If your STB has a Scart (EURO-AV) connector

The illustration below shows an example of connecting the STB to LINE-3 IN.

You can watch programmes from the Set-Top Box connected to this VCR on your TV even

when the VCR is turned off using the Line Through function. When you turn on the STB, this

VCR automatically sends the signal from the STB to the TV without turning itself on.

Note

• You cannot watch programmes from your STB on the TV while recording unless you record

a programme from your STB.

1

Connect the STB to the LINE-3IN connector as shown above.

2

Set POWER SAVE to OFF in the OTHER OPTIONS menu.

3

Turn off the VCR.

To watch a programme from the STB, turn on the STB and the TV.

AERIAL

OUT

Scart cable (supplied with

the STB)

Scart cable (not supplied)

Aerial cable (supplied)

STB

i

LINE-

1 (TV)

t

LINE

- 3 IN

: Signal flow

Scart

(EURO-AV)

AERIAL

IN

AERIAL IN

Scart

(EURO-AV)

continued

14

Connecting the VCR

filename[01GB04GET-NP0.fm] model name1[SLV-SF990G(ENG)] model name2[]

[3-062-324-

11

(1)]

If your STB does not have a Scart (EURO-AV) connector.

* If your TV doesn’t have a Scart (EURO-AV) connector, the Scart cable connected to the

VCR is not required.

Additional connections

To a stereo system

You can improve sound quality by

connecting a stereo system to the AUDIO

OUT R/L jacks as shown on the right.

AERIAL

IN

Aerial cable

(not supplied)

Scart cable* (not supplied)

Aerial cable (supplied)

AERIAL

OUT

STB

i

LINE-

1 (TV)

: Signal flow

Scart

(EURO-AV)

AERIAL IN

AUDIO OUT

R/L

LINE IN

Audio cable (not supplied)

Getting Started

15

Tuning your TV to the VCR

filename[01GB04GET-NP0.fm] model name1[SLV-SF990G(ENG)] model name2[]

[3-062-324-

11

(1)]

Step 4 : Tuning your TV to the VCR

If you have connected your VCR to the TV with an aerial

cable only

1

Turn on your TV and press

?

/

1

(on/standby) to turn on the VCR.

Pull down the drop down panel.

2

Press briefly RF CHANNEL on the VCR.

The factory-preset RF (Radio Frequency) channel appears in the display

window..

3

Turn on your TV and select an unused programme position for the VCR

picture (for ex. programme position "0").

This programme position will be referred to as the video channel (for

watching your VCR on the TV) after tuning is completed.

g

RF CHANNEL

PROGRAM +/–

?

/

1

•

AUTO SET UP

RF CHANNEL

TV

STEREO

AUTO SET UP

S

M

H

LP

EP

SP

VIDEO

EDIT

NICAM

VPS

PDC

OPC

SMARTLINK

continued

16

Tuning your TV to the VCR

filename[01GB04GET-NP0.fm] model name1[SLV-SF990G(ENG)] model name2[]

[3-062-324-

11

(1)]

To check if the TV tuning is correct

Set the TV to the video channel (for ex. programme position "0") and press

PROGRAM +/– on the VCR. If the TV screen changes to a different programme each

time you press PROGRAM +/–, the TV tuning is correct.

To obtain a clear picture from the VCR

If the screen does not appear clearly in step 4 above, press PROGRAM +/–, so that

another RF channel appears.Then tune the TV to the new RF channel until a clear

picture appears.

4

Tune in the programme position you have

selected (for ex. programme position "0")

until the picture shown on the right appears

clearly on the TV screen (background must

be green).

Refer to your TV manual for tuning

instructions.

If the picture does not appear clearly, see

“To obtain a clear picture from the VCR”

below.

5

Press RF CHANNEL.

You have now tuned your TV to the VCR. From now on, whenever you

want to play a tape, set the TV to the video channel (for ex. programme

position "0").

You can now set your VCR with the Auto Set Up function (see page 18).

SONY VIDEO CASSETTE RECORDER

AUTO SET UP

RF CHANNEL

Getting Started

17

Tuning your TV to the VCR

filename[01GB04GET-NP0.fm] model name1[SLV-SF990G(ENG)] model name2[]

[3-062-324-

11

(1)]

If you have connected your VCR to the TV with a Scart

(EURO-AV) connector and an aerial cable as well

In order to avoid any interferences with existing broadcasts, we recom-

mend you to set RF channel to the OFF position.

Note

• If in step 3 the green screen does not appear, select the "AV/EXTERNAL" source on your TV

(please refer to your TV instruction manual).

1

Turn on your TV and press

?

/

1

(on/standby) to turn on the VCR.

Pull down the drop down panel.

2

Press briefly RF CHANNEL on the VCR.

The factory-preset RF (Radio Frequency) channel appears in the display

window.

3

Press PROGRAM +/- until the OFF indication appears in the display

window. The RF channel is then switched off.

The picture shown below appears clearly on the TV screen (background

must be green).

4

Press RF CHANNEL again.

You can now set your VCR with the Auto Set Up function (see page 18).

g

RF CHANNEL

PROGRAM +/–

•

AUTO SET UP

RF CHANNEL

TV

STEREO

AUTO SET UP

S

M

H

LP

EP

SP

VIDEO

EDIT

NICAM

VPS

PDC

OPC

SMARTLINK

TRACKING

- PROGRAM +

TV

STEREO

AUTO SET UP

SMH

LP

EP

SP

VIDEO

EDIT

NICAM

VPS

PDC

OPC

SMARTLINK

SONY VIDEO CASSETTE RECORDER

AUTO SET UP

RF CHANNEL

18

Setting up the VCR with the Auto Set Up function

filename[01GB04GET-NP0.fm] model name1[SLV-SF990G(ENG)] model name2[]

[3-062-324-

11

(1)]

Step 5 : Setting up the VCR with the Auto

Set Up function

Before using the VCR for the first time, set up the VCR using the Auto Set Up

function.With this function, you can set the language for the on-screen display, TV

channels, guide channels for the VIDEO Plus + system, and VCR clock

automatically.

Before you start ...

• Turn on the set -top box if it is connected to the VCR only by the aerial cable and not to the

Scart cable.

To cancel the Auto Set Up function

Press AUTO SET UP.

Notes

• Do not cancel the Auto Set Up function during step 3. If you do, repeat Auto Set Up from the

beginning.

• When you operate the Auto Set Up function, some of the settings (VIDEO Plus +, timer

etc...) will be reset. In this case, you have to set them again.

g

PROGRAM +/–

AUTO SET UP

Hold down AUTO SET UP on the VCR for more than 3 seconds.

The VCR automatically turns on, and starts searching for all of the

receivable channels and presets them in the appropriate order for your local

area.

If you use the SMARTLINK connection, the Preset Download function

starts and the SMARTLINK indicator flashes in the display window during

download.

After the search or download is complete, the current time appears in the

display window for any stations that transmit a time signal.

AUTO SET UP

RF CHANNEL

TV

STEREO

AUTO SET UP

SMH

LP

EP

SP

VIDEO

EDIT

NICAM

VPS

PDC

OPC

SMARTLINK

Getting Started

19

Setting the clock

filename[01GB04GET-NP0.fm] model name1[SLV-SF990G(ENG)] model name2[]

[3-062-324-

11

(1)]

Step 6 : Setting the clock

You must set the time and date on the VCR to

use the timer recording features properly.

If the VCR clock was not set in the Auto Set

Up procedure, you need to set it manually.

The Auto Clock Set function works only if a

station in your area is broadcasting a time

signal. If the Auto Set Up function did not set

the clock correctly for your local area, try

another station for the Auto Clock Set

function.

Setting the clock manually

Before you start

…

• Turn on the VCR and the TV.

• Set the TV to the video channel.

MENU

M/m/</,

OK

1

Press MENU, then press

M

/

m

to

highlight SETTINGS and press OK.

2

Press

M

/

m

to highlight CLOCK, then

press OK.

MENU

OK

PLAY

SET :

SELECT :

OK

MENUEXIT :

SETTINGS

TUNER

CLOCK

LANGUAGE

RETURN

TV GUIDE PAGE

OK

PLAY

SET :

SELECT :

OK

MENUEXIT :

CLOCK

OFFAUTO ADJUST

MANUAL ADJUST

.1 1 . 20 00 SAT 0 : 0 0

continued

20

Setting the clock

filename[01GB04GET-NP0.fm] model name1[SLV-SF990G(ENG)] model name2[]

[3-062-324-

11

(1)]

3

Press

M

/

m

to highlight MANUAL

ADJUST, then press OK.

4

Press

M

/

m

to set the date.

5

Press

,

to highlight the month and set

the month pressing

M

/

m

.

6

Set the year, hour, and minutes in

sequence, pressing

,

to highlight the

item to be set, and press

M

/

m

to select

the digits.

The day of the week is set automatically.

7

Press OK to confirm the setting and start

the clock.

8

Press MENU to exit the menu.

OK

PLAY

CONFIRM :

SET :

OK

MENUEXIT :

CLOCK

OFFAUTO ADJUST

MANUAL ADJUST

1.1.2000 SAT 0:00

SELECT :

OK

PLAY

CONFIRM :

SET :

OK

MENUEXIT :

CLOCK

OFFAUTO ADJUST

MANUAL ADJUST

28 . 1 . 2 000 FRI 0 : 0 0

SELECT :

OK

PLAY

CONFIRM :

SET :

OK

MENUEXIT :

CLOCK

OFFAUTO ADJUST

MANUAL ADJUST

8.9.2000 THU 0:00

SELECT :

2

OK

PLAY

CONFIRM :

SET :

OK

MENUEXIT :

CLOCK

OFFAUTO ADJUST

MANUAL ADJUST

8.9.2000 THU 8:00

SELECT :

21

OK

PLAY

MENUEXIT :

CLOCK

OFFAUTO ADJUST

MANUAL ADJUST

8.9.2000 THU 8:00

21

SET :

SELECT :

OK

MENU

Page is loading ...

Sony SLV-SF900G User manual

Sony SLV-SF900G User manual

Related papers

Other documents