dji Tuned Propulsion System User manual

DJI E600 Multi-rotor Propulsion System

User Manual V 1.04

August, 2014 Revision

Disclaimer

Thank you for purchasing the E600. Read this disclaimer carefully before using this product. By using this

product, you hereby agree to this disclaimer and signify that you have read them fully. DJI Innovations assumes

no liability for damage(s) or injuries incurred directly or indirectly from the use of this product.

DJI is the registered trademark of DJI Innovations. Names of product, brand, etc., appearing in this manual are

trademarks or registered trademarks of their respective owner companies. This product and manual are

in any form without the prior written consent or authorization of DJI Innovations. No patent liability is assumed

with respect to the use of the product or information contained herein.

Cautions

When flying, the fast rotating propellers will cause serious damage and injury. Therefore, please fly with a high

safety consciousness.

1. Keep flying multi-rotor away from obstacles, human beings, high-voltage lines and so on.

2. Do not get close to or touch the working motors and propellers, which will cause serious injury.

3. Make sure there is no short or open circuit.

4. Check that the propellers and the motors are installed correctly and firmly before flight.

5. Check whether all parts of multi-rotor are in good condition before flight. Do not fly with old or broken

parts.

6. Use DJI parts as much as possible.

If you have any problem you cannot solve, please contact your dealer or DJI customer service.

In the Box

Motor(Clock-wise rotation)

Motor(Counter clock-wise rotation)

Propeller Pair

ESC

Accessories Pack

Power Hub,

Screws ( M2.5*Φ5*1.3*1) , Screws ( M3*Φ4.9*6.8), Screws ( M3*Φ5.5*4.5),

Wrench for propeller fix, 2.0mm hexagonal wrench, Double side tape, etc.

Tools Needed

Tool

Function

Electric Soldering Iron & Soldering Tin

Connects the ESC’s power cables to the power hub.

Soldering the ESC

1. Please solder the ESC to the power pads on the power hub as the figure shows. Make sure the welding

spot is firmly attached on the power pads and no short circuit. Do not damage the protector of the red

cable to avoid short circuit.

2. Connect the signal cable to your controller.

3. Connect the motor to the ESC. Make sure the rotation direction of each motor is the same as the way of

defined rotation direction. If not, switch any of two cables that connecting the motor and the ESC to

change its rotation direction.

The outer power pads are for the GND cables, and the

inner power pads are for the power cables. Make sure to

solder them correctly. Try to make the cables firmly

soldered on the power hub with suited length (Should not

leave any outside the power hub), and outward-facing.

To the controller

Make sure there is no short or open circuit.

It is recommended to solder a power connector on the power hub.

Assembling the Propellers

Propeller

Silver nut (1242)

Black nut (1242 R)

Diagram

Assembly Location

Motor(Counter clock-wise rotation)

Motor(Clock-wise rotation)

Fastening/Un-fastening

Instructions

Lock: Tighten the propeller in this direction.

Unlock: Remove the propeller in this direction.

1. Tighten the propellers by following the instructions. Propellers are self tightening during flight.

2. Keep the motor deadlocked in place and remove the propeller according to the instructions.

DO NOT use any thread locker on the threads.

Assembling the Motors

Assemble the motor to a frame arm according to the size of the assembly hole.

(1) The screw hole is M3. Assemble them with appropriate screws.

(2) Oversized screws may damage the motor.

1 mm9

6x M3-6H

Thread depth

3mm

16mm

25mm

12mm

4x M3-6H Thread depth 4mm

13mm

ESC Sound Description

Normal

Description

♪1234567

Ready.

Abnormal

Description

BBBBBB…

Throttle stick is not at bottom.

B--------B--------B…

Input signal is abnormal.

BB---BB---BB---BB…

Input voltage is abnormal

You can know the working status according to the sound of the ESC.

Specifications

Working Temperature

-5°C ~ 40°C

ESC

Current

20A OPTO

Signal Frequency

30Hz~450Hz

Voltage

22.2V

Battery

6S LiPo

Motor

Stator Size

35X8mm

KV

415rpm/V

Weight

90g

Propeller

Diameter / Thread Pitch

12X4.2 inch

Used Together with DJI Product

Product list and assembly diagram

Used Together with the DJI F450

DJI F450

dji Tuned Propulsion System User manual

This manual is also suitable for

dji Tuned Propulsion System User manual

Related papers

Other documents