Philips GC3640/07 User manual

Brand: Philips

Model: GC3640/07

Category: Irons

Type: User manual

Page is loading ...

Introduction

Congratulations on your purchase and welcome to Philips! To fully benet

from the support that Philips offers, register your product at www.philips.

com/welcome.

This user manual contains information about the surprising features of this

iron and some tips to make ironing easier and more enjoyable.

This iron is equipped with a special sensor-controlled handle and automatic

energy-saving technology.

While you iron, the sensor in the handle ensures that the iron produces the

optimal amount of steam. As 90% of the energy consumption of an iron

is used to create steam, energy consumption is optimised by optimising

the steam output. When you intuitively put more force on the handle to

remove stubborn creases, the iron automatically produces more steam.

When you do not press the handle, when you lift the iron and when the

iron is standing on its heel or on its soleplate without any movement, the

automatic energy-saving technology limits the steam output to reduce

energy consumption.

We hope you enjoy using this iron.

Important

Read this user manual carefully before you use the appliance and save it for

future reference.

Danger

- Never immerse the iron in water.

Warning

- Check if the voltage indicated on the appliance corresponds to the local

mains voltage before you connect the appliance.

- Do not use the appliance if the plug, the mains cord or the appliance

itself shows visible damage, or if the appliance has been dropped

or leaks.

- If the mains cord is damaged, you must have it replaced by Philips, a

service centre authorised by Philips or similarly qualied persons in

order to avoid a hazard.

- Never leave the appliance unattended when it is connected to the

mains.

- This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for

their safety.

- Children should be supervised to ensure that they do not play with the

appliance.

- Do not let the mains cord come into contact with the hot soleplate of

the iron.

- Do not use the appliance if the exible rubber handle parts show visible

damage.

Caution

- Only connect the appliance to an earthed wall socket.

- Check the mains cord regularly for possible damage.

- The soleplate of the iron can become extremely hot and may cause

burns if touched.

- When you have nished ironing, when you clean the appliance, when

you ll or empty the water tank and also when you leave the iron even

for a short while: set the steam control to position 0, put the iron on its

heel and remove the mains plug from the wall socket.

- Always place and use the iron on a stable, level and horizontal surface.

- Do not put perfume, vinegar, starch, descaling agents, ironing aids or

other chemicals in the water tank.

- This appliance is intended for household use only.



This Philips appliance complies with all standards regarding electromagnetic

elds (EMF). If handled properly and according to the instructions in this

user manual, the appliance is safe to use based on scientic evidence

available today.



A Spray nozzle

B Filling opening

C Cap of lling opening

D Steam boost button ( 9)

E Steam control

- CALC CLEAN = Calc-Clean function

- 0 = no steam

- l = minimum steam

- ; = maximum steam

F Spray button ( 8)

G Red auto-off light (GC3660 only)

H Temperature dial

I Temperature light

J Mains cord

K Flexible rubber handle part

L Anti-Calc tablet

M Water tank

N Heel

Not shown: lling cup

Before first use

1 Remove any sticker, protective foil or plastic from the

soleplate (Fig. 2).

Preparing for use



Do not put perfume, vinegar, starch, descaling agents, ironing aids or other

chemicals in the water tank.

1 Make sure the appliance is unplugged.

2 Set the steam control to position 0 (= no steam) (Fig. 3).

3 Openthecapofthellingopening.

4 Usethellingcuptollthewatertankwithtapwateruptothe

maximum level. Tilt the iron backwards to check if the water level has

reached the MAX indication (Fig. 4).

Do not ll the water tank beyond the MAX indication.

5 Closethecapofthellingopening(‘click’).

Setting the temperature

Temperature and steam settings

Fabric type Temperature

setting

Steam setting Steam boost

Linen MAX

;

Yes

Cotton 3

;

Yes

Wool 2

N.A.

Silk 1 0 N.A.

Synthetic fabrics

(e.g. acrylic, nylon,

polyamide, polyester)

1 0 N.A.

Check the laundry care label for the required ironing temperature.

If you do not know what kind or kinds of fabric an article is made of,

determine the right ironing temperature by ironing a part that is not visible

when you wear or use the article.

Silk, woolen and synthetic materials: iron the reverse side of the fabric to

prevent shiny patches. To prevent stains, do not use the spray function.

Start ironing the articles that require the lowest ironing temperature, such

as those made of synthetic bers.

1 Put the iron on its heel.

2 To set the required ironing temperature, turn the temperature dial to

the appropriate position (Fig. 5).

See table ‘Temperature and steam settings’.

3 Put the mains plug in an earthed wall socket.

, The temperature light goes on (Fig. 6).

4 When the temperature light goes out, wait a while before you

start ironing.

Note: The temperature light goes on from time to time during ironing.

Using the appliance

Note: The iron may give off some smoke when you use it for the rst time. This

stops after a short while.



- While you iron, the sensor in the handle ensures that the iron produces

the optimal amount of steam. As 90% of the energy consumption of

an iron is used to create steam, energy consumption is optimised by

optimising the steam output. When you intuitively put more force on

ENGLISH

4239.000.7182.2

Note: If the temperature light does not go on after you move the iron, the

soleplate still has the right temperature and the iron is ready for use.

Cleaning and maintenance

Cleaning

1 Set the steam control to position 0, remove the mains plug from the

wall socket and let the iron cool down.

2 Wipeakesandanyotherdepositsoffthesoleplatewithadamp

cloth and a non-abrasive (liquid) cleaning agent.

To keep the soleplate smooth, avoid hard contact with metal objects.

Never use a scouring pad, vinegar or other chemicals to clean the

soleplate.

3 Clean the upper part of the iron with a damp cloth.

4 Regularly rinse the water tank with water. Empty the water tank after

you have rinsed it (Fig. 14).

Double-Active Calc System

The Double-Active Calc System consists of an Anti-Calc tablet inside the

water tank combined with the Calc-Clean function.

1 The Anti-Calc tablet prevents scale from clogging the steam vents. This

tablet is constantly active and does not need to be replaced (Fig. 15).

2 The Calc-Clean function removes the scale particles from the iron.

Calc-Clean function

Use the Calc-Clean function once every two weeks. If the water in your

area is very hard (i.e. when akes come out of the soleplate during ironing),

use the Calc-Clean function more frequently.

1 Set the steam control to position 0 and remove the mains plug from

the wall socket.

2 Fill the water tank to the maximum level.

Do not pour vinegar or other descaling agents in the water tank.

3 Set the temperature dial to MAX.

4 Put the mains plug in an earthed wall socket.

5 Unplug the iron when the temperature light goes out.

6 Hold the iron over the sink. Push the steam control to the CALC

CLEAN position and hold it. Gently shake the iron to and fro (Fig. 16).

, Steam and boiling water come out of the soleplate. Impurities and

akes(ifany)areushedout.

7 Release the steam control as soon as all the water in the tank has

been used up.

8 Repeat the Calc-Clean process if the iron still contains a lot of

impurities.

After the Calc-Clean process

1 Put the plug back into the wall socket and let the iron heat up to let

the soleplate dry.

2 Unplug the iron when the temperature light goes out.

3 Move the iron gently over a piece of used cloth to remove any water

stains that may have formed on the soleplate.

4 Let the iron cool down before you store it.

Storage

1 Set the steam control to position 0, remove the mains plug from the

wall socket and let the iron cool down.

2 Wind the mains cord round the cord storage facility (Fig. 17).

Note: Make sure that the mains cord does not press down the handle during

storage.

3 Store the iron on its heel in a safe and dry place.

Environment

- Do not throw away the appliance with the normal household waste

at the end of its life, but hand it in at an ofcial collection point for

recycling. By doing this, you help to preserve the environment (Fig. 18).

Guarantee & service

If you need service or information or if you have a problem, please visit

the Philips website at www.philips.com or contact the Philips Consumer

Care Centre in your country (you nd its phone number in the worldwide

the handle to remove stubborn creases, the iron automatically produces

more steam.

- When you do not press the handle, when you lift the iron and

when the iron is standing on its heel or on its soleplate without any

movement, the automatic energy-saving technology limits the steam

output to reduce energy consumption (Fig. 7).

Steam ironing

1 Make sure that there is enough water in the water tank.

2 Settherecommendedironingtemperature(seechapter‘Preparing

foruse’,table‘Temperatureandsteamsettings’).

3 Set the appropriate steam setting. Make sure that the steam setting is

suitableforthesetironingtemperature(seechapter‘Preparingfor

use’,table‘Temperatureandsteamsettings’)(Fig.8).

Note: The iron is ready for steam ironing as soon as it has reached the

set ironing temperature.

Note: If the set ironing temperature is too low (MIN to 2), water may drip

from the soleplate (see chapter ‘Features’, section ‘Drip stop’).



1 Set the steam control to position 0 (= no steam) (Fig. 3).

2 Settherecommendedironingtemperature(seechapter‘Preparing

foruse’,table‘Temperatureandsteamsettings’).



Spray function

You can use the spray function to remove stubborn creases at any

temperature.

1 Make sure that there is enough water in the water tank.

2 Press the spray button several times to moisten the article to be

ironed (Fig. 9).

Steam boost

A powerful steam boost helps to remove very stubborn creases.

The steam boost function can only be used at temperature settings

between 3 and MAX.

1 Press and release the steam boost button (Fig. 10).

Concentrated steam boost from the special Steam Tip



The concentrated steam boost from the long vents in the Steam

Tip enhances the distribution of steam into every part of your garment.

The concentrated steam boost function can only be used at temperature

settings between 3 and MAX.

1 Press and release the steam boost button (Fig. 11).

Vertical steam boost

You can also use the steam boost function when you hold the iron in

vertical position. This is useful for removing creases from hanging clothes,

curtains etc.

1 Hold the iron in vertical position and press and release the steam

boost button (Fig. 12).

Never direct the steam at people.

Drip stop

This iron is equipped with a drip-stop function: the iron automatically stops

producing steam when the temperature is too low, to prevent water from

dripping out of the soleplate. When this happens, you may hear a sound.



The automatic shut-off function automatically switches off the iron if it has

not been moved for a while.

, Theredauto-offlightashestoindicatethattheironhasbeen

switched off by the automatic shut-off function (Fig. 13).

To let the iron heat up again:

1 Pick up the iron or move it slightly

, The red auto-off light goes out.

, If the temperature of the soleplate has dropped below the set ironing

temperature, the temperature light goes on.

2 If the temperature light goes on after you have moved the iron, wait

for it to go out before you start ironing.

4239.000.7182.2

Problem Possible cause Solution

The red

auto-off light

ashes

(specic

types only).

The automatic shut-

off function has

switched off the

iron (see chapter

‘Features’).

Move the iron slightly to deactivate

the automatic shut-off function. The

red auto-off light goes out.

guarantee leaet). If there is no Consumer Care Centre in your country, go

to your local Philips dealer.

Troubleshooting

This chapter summarises the most common problems you could encounter

with the appliance. If you are unable to solve the problem with the

information below, contact the Consumer Care Centre in your country.

Problem Possible cause Solution

The iron

is plugged

in, but the

soleplate

stays cold.

There is a

connection

problem.

Check the mains cord, the plug and

the wall socket.

The temperature

dial is set to MIN.

Set the temperature dial to the

required position.

The iron

does not

produce any

steam.

There is not

enough water in the

water tank.

Fill the water tank (see chapter

‘Preparing for use’, section ‘Filling

the water tank).

The steam control

is set to position 0.

Set the steam control to l or ;

(see chapter ‘Preparing for use’,

table ‘ Temperature and steam

settings’).

The iron is not hot

enough and/or the

drip-stop function

has been activated.

Set an ironing temperature that is

suitable for steam ironing ( 2 to

MAX). Put the iron on its heel and

wait until the temperature light

goes out before you start ironing.

The steam

boost

function

does not

work

properly.

You used the steam

boost function too

often within a short

period.

Continue ironing in horizontal

position and wait a while before

you use the steam boost function

again..

The iron is not hot

enough.

Set an ironing temperature at which

the steam boost function can be

used ( 3 to MAX). Put the

iron on its heel and wait until the

temperature light goes out before

you use the steam boost function.

Water

droplets drip

onto the

fabric during

ironing

You have not closed

the cap of the lling

opening properly.

Press the cap until you hear a click.

You have put an

additive in the

water tank.

Rinse the water tank and do not

put any additive in the water tank.

You have used

the steam boost

function at a

temperature setting

below 3.

Set the temperature dial to a

setting between 3 and MAX

You have set a too

low temperature

for steam ironing.

Set an ironing temperature that is

suitable for steam ironing ( 2 to

MAX). Put the iron on its heel and

wait until the temperature light

goes out before you start ironing

Water drips

from the

soleplate

after the iron

has cooled

down or has

been stored.

You have put the

iron in horizontal

position with water

still left in the water

tank.

Empty the water tank before you

store the iron. Store the iron on

its heel.

Flakes and

impurities

come out of

the soleplate

during

ironing.

Hard water forms

akes inside the

soleplate.

Use the Calc-Clean function one or

more times (see chapter ‘Cleaning

and maintenance’, section ‘Calc-

Clean function’).

4239.000.7182.2

Page is loading ...

Philips GC3640/07 User manual

Brand: Philips

Model: GC3640/07

Category: Irons

Type: User manual

Download PDF

report

in other languages

italiano: Philips GC3640/07 Manuale utente
français: Philips GC3640/07 Manuel utilisateur
Deutsch: Philips GC3640/07 Benutzerhandbuch

Philips GC3640/07 User manual

Philips GC3640/07 User manual

in other languages

Related papers

Other documents