3com S9508V Installation guide

H3C S9500 Series Routing Switches

Installation Manual

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Manual Version: T2-08048H-20071025-C-2.03

Product Version: S9500-CMW520-R2127

No part of this manual may be reproduced or transmitted in any form or by any means

without prior written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H

3

Care,

, TOP G, , IRF, NetPilot,

Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware,

Storware, NQA, VVG, V

2

G, V

n

G, PSPT, XGbus, N-Bus, TiGem, InnoVision and

HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their

respective owners.

Notice

The information in this document is subject to change without notice. Every effort has

been made in the preparation of this document to ensure accuracy of the contents, but

all statements, information, and recommendations in this document do not constitute

the warranty of any kind, express or implied.

To obtain the latest information, please access:

http://www. h3c.com

Technical Support

customer_service@h3c.com

http://www. h3c.com

About This Manual

Related Documentation

The related manuals are listed in the following table.

Manual Description

H3C S9500 Series Routing

Switches Operation Manual

It provides an operation guide. It consists of access

volume, IP service volume, IP routing volume, IP

multicast volume, MPLS/VPN volume, QoS/ACL

volume, security volume, system volume, and

acronyms.

H3C S9500 Series Routing

Switches Command Manual

It explains all commands available in the S9500

series and provides a list of commands the S9500

series do not support. It consists of the same

modules as the operation manual.

Organization

H3C S9500 Series Routing Switches Installation Manual is organized as follows:

Chapter Contents

1 Product Overview

Introduces the appearance, architecture and system

features of the S9500 series.

2 Preparing for Installation

Lists the preparations and precautions for the

installation.

3 Installing the Switch

Details the installation of the chassis, PSUs, boards

and cable connection for the S9500 series.

4 Commissioning the

Switch

Concentrates on the initial power-on and booting of

the S9500 series.

5 Troubleshooting and

Maintaining the Switch

Presents troubleshooting the switch ,the hardware

and software upgrade.

6 Appendix A Cable

Management

Introduces how to bind cables.

7 Appendix B Engineering

Labels for Cables

Introduces the use of engineering labels.

Chapter Contents

8 Appendix C Installation

of Lightning Arrester for

AC Power

Introduces the installation of lightning arrester for AC

power of S9500 series routing switches.

Conventions

The manual uses the following conventions:

I. Command conventions

Convention Description

Boldface

The keywords of a command line are in Boldface.

italic

Command arguments are in italic.

[ ]

Items (keywords or arguments) in square brackets [ ] are

optional.

{ x | y | ... }

Alternative items are grouped in braces and separated by

vertical bars. One is selected.

[ x | y | ... ]

Optional alternative items are grouped in square brackets

and separated by vertical bars. One or none is selected.

{ x | y | ... } *

Alternative items are grouped in braces and separated by

vertical bars. A minimum of one or a maximum of all can be

selected.

[ x | y | ... ] *

Optional alternative items are grouped in square brackets

and separated by vertical bars. Many or none can be

selected.

&<1-n>

The argument(s) before the ampersand (&) sign can be

entered 1 to n times.

# A line starting with the # sign is comments.

II. GUI conventions

Convention Description

< >

Button names are inside angle brackets. For example, click

<OK>.

[ ]

Window names, menu items, data table and field names

are inside square brackets. For example, pop up the [New

User] window.

/

Multi-level menus are separated by forward slashes. For

example, [File/Create/Folder].

III. Symbols

Convention Description

Warning

Means reader be extremely careful. Improper operation

may cause bodily injury.

Caution

Means reader be careful. Improper operation may cause

data loss or damage to equipment.

 Note Means a complementary description.

Environmental Protection

This product has been designed to comply with the requirements on environmental

protection. For the proper storage, use and disposal of this product, national laws and

regulations must be observed.

Installation Manual

H3C S9500 Series Routing Switches Table of Contents

i

Table of Contents

Chapter 1 Product Overview ........................................................................................................1-1

1.1 Introduction........................................................................................................................1-1

1.2 Physical Structure..............................................................................................................1-1

1.2.1 Chassis and Slots ...................................................................................................1-2

1.2.2 Backplane................................................................................................................1-5

1.2.3 Power System.........................................................................................................1-6

1.2.4 PoE Power Supply..................................................................................................1-8

1.2.5 Fan Tray................................................................................................................1-10

1.3 Switching and Routing Processing Unit...........................................................................1-11

1.4 Line Processing Unit........................................................................................................1-12

1.5 Service Board ..................................................................................................................1-14

1.6 System Specifications......................................................................................................1-14

Installation Manual

H3C S9500 Series Routing Switches Chapter 1 Product Overview

1-1

Chapter 1 Product Overview

1.1 Introduction

The S9500 Series Routing Switches (hereinafter referred to as the S9500 series) are

developed by Hangzhou H3C Technologies Co., Ltd. (hereinafter referred to as H3C)

for use on business-oriented enterprise networks, the distribution layer of large MANs,

the core layer of small MANs, and the backbone of large enterprise networks and

campus networks. They can serve as switching cores and convergence centers.

Currently, the S9500 series consist of the following models:

z S9505: This model provides a switching capacity of up to 600 Gbps. It allows for

the concurrent wire-speed forwarding on 240 GE ports, 20 × 10GE ports, 240 FE

electrical ports, or 100 FE optical ports.

z S9508: This model provides a switching capacity of up to 960 Gbps. It allows for

the concurrent wire-speed forwarding on 384 GE ports, 32 × 10GE ports, 384 FE

electrical ports, or 160 FE optical ports.

z S9508V: This model provides a switching capacity of up to 960 Gbps. It allow for

the concurrent wire-speed forwarding on 384 GE ports, 32 × 10GE ports, 384 FE

electrical ports, or 160 FE optical ports. This model adopts upright slots.

z S9512: This model provides a switching capacity of up to 1.44 Tbps. It allows for

the concurrent wire-speed forwarding on 576 GE ports, 48 × 10GE ports, 576 FE

electrical ports, or 240 FE optical ports.

 Note:

Unless otherwise specified in this document, the S9508V and the S9508 have the

same configuration.

1.2 Physical Structure

The S9500 series use integrated chassis, which consists of a power area, board area,

backplane, and fan area.

Installation Manual

H3C S9500 Series Routing Switches Chapter 1 Product Overview

1-2

 Note:

z Two switching and routing processor units (SRPUs) can be installed on the S9500

series to support active-standby switchover.

z Two power supply units (PSUs) can be installed on the S9500 series to provide

hot-standby 1+1 redundancy.

z The S9500 series support PoE and an external PoE power supply is optional.

z Boards, fan tray, and AC/DC PSUs are hot-swappable.

1.2.1 Chassis and Slots

I. S9505

(1) SRPU slots (2) LPU slots (3) Cable management bracket

(4) PSUs (5) PoE power entry module (6) Fan tray

Figure 1-1 Front view of the S9505

z The S9505 chassis provides seven slots in its board area: The top two

accommodate SRPUs, which can operate in 1+1 redundancy mode; the remaining

five accommodate LPUs/service boards.

z At the bottom of the chassis is the power area that contains one PoE entry module

and two PSUs. The two PSUs are hot-swappable; they can operate in 1+1

redundancy mode. The switch supports both AC and DC power inputs. So you can

select AC or DC PSUs as needed.

Installation Manual

H3C S9500 Series Routing Switches Chapter 1 Product Overview

1-3

z On the right of the chassis is the fan area that contains one vertical fan tray. The

fans draw air in from the left and exhausts air from the right.

II. S9508

(1) LPU slots (2) SRPU slots (3) PSUs

(4) PoE power entry module (5) Fan tray

Figure 1-2 Front view of the S9508

z The S9508 chassis provides ten slots in its board area: The middle two

accommodate SRPU modules; the remaining eight accommodate LPUs/service

boards.

z At the bottom of the chassis is the power area that contains one PoE power entry

module and two PSUs. The switch supports both AC and DC power inputs. So you

can select AC or DC PSUs as needed.

z On the right of the chassis is the fan area that contains one vertical fan tray. The

fans draw air in from the left and exhausts air from the right.

Installation Manual

H3C S9500 Series Routing Switches Chapter 1 Product Overview

1-4

III. S9508V

(1) Fan tray (2) LPU slots (3) SRPU slots

(4) Air filter (5) PSUs (6) PoE power entry module

Figure 1-3 Front view of the S9508V

z The S9508V chassis provides ten vertical slots in its board area: The middle two

accommodate SRPU modules; the remaining eight accommodate LPU/service

boards.

z At the bottom of the chassis is the power area that contains one PoE power entry

module and two PSUs. The switch supports both AC and DC power inputs. So you

can select AC or DC PSUs as needed.

z Above the power area is the air filter, which can be removed from the chassis in

the case of replacement or regular cleaning.

z On the top of the chassis is the fan area that contains one horizontal fan tray. The

fans draw air in from the bottom and exhaust air from the top.

Installation Manual

H3C S9500 Series Routing Switches Chapter 1 Product Overview

1-5

IV. S9512

(1) LPU slots (2) SRPU slots (3) PSUs

(4) PoE power entry module (5) Fan trays

Figure 1-4 Front view of the S9512

z The S9512 chassis provides fourteen slots in its board area: The middle two

accommodate SRPU modules and the remaining twelve accommodate

LPUs/service boards.

z At the bottom of the chassis is the power area that contains one PoE entry module

and two PSUs. The switch supports both AC and DC power inputs. So you can

select AC or DC PSUs as needed.

z On the right of the chassis is the fan area that contains two vertical fan trays. The

fans draw air in from the left and exhaust air from the right.

1.2.2 Backplane

The backplane of the S9500 series allows high-speed data exchange between SRPUs

and LPUs, as well as the exchange of various management and control signals in the

system.

Installation Manual

H3C S9500 Series Routing Switches Chapter 1 Product Overview

1-6

I. Functions

The following are the main functions of the backplane:

z Providing communication channels for signal exchange between boards

z Supporting board hot-swapping

z Supporting board auto-discovery in slots

z Connecting PSUs to distribute power SRPUs, LPUs/service boards, and fan tray(s)

and providing monitor channels for them.

II. Structure

The S9500 series use a passive backplane, which provides multiple board slots, one or

two fan interfaces, and two –48V power interfaces (one for PSUs and the other for PoE

power entry module).

1.2.3 Power System

 Note:

z The S9500 series support both AC and DC power inputs. So you can choose AC or

DC PSUs as needed.

z The S9500 series support 1+1 power supply redundancy.

z The PSUs of the S9500 series are hot-swappable.

The power system is at the bottom of the chassis. In the PSU slots, you can insert either

two AC PSUs or two DC PSUs. The PSUs are cooled by the built-in fans, which draw

air into the chassis from the front and exhaust air from the rear.

z AC PSU

Table 1-1 Specifications for AC PSUs

Specifications

Item

NEPS1200-A NEPS2000-A NEPS3500-A

Model S9505 S9508/S9512 S9508/S9512

Rated

voltage

range

100 to 240 VAC, 50

Hz or 60 Hz

100 to 120 VAC, 60 Hz

200 to 240 VAC, 50 Hz

100 to 240 VAC,

50 Hz or 60 Hz

Input

voltage

range

90 to 264 VAC, 50 Hz

or 60 Hz

90 to 264 VAC, 50 Hz or

60 Hz

90 to 264 VAC, 50

Hz or 60 Hz

Installation Manual

H3C S9500 Series Routing Switches Chapter 1 Product Overview

1-7

Specifications

Item

NEPS1200-A NEPS2000-A NEPS3500-A

Max

input

current

15 A 15 A

Single 1800 W

sub-PSU :15 A

Two 1800W

sub-PSUs: 30 A

Table 1-2 Configuration and output power of AC PSUs

PSU Configuration

Maximum output

power

NEPS1200-A

1 × NEPS1200-A, no redundancy

2 × NEPS1200-A, 1+1 redundancy

1200 W (90 V to 264 V)

NEPS2000-A

1 × NEPS2000-A, no redundancy

2 × NEPS2000-A, 1+1 redundancy

1200 W (90 V to 160 V)

2000 W (160 V to 264 V)

1 × NEPS3500-A enclosure + 1 ×

sub-PSU, no redundancy

1 × NEPS3500-A enclosure + 2 ×

sub-PSU, 1+1 redundancy

1200 W (90 V to 180 V)

1800 W (180 V to 264 V)

1 × NEPS3500-A enclosure + 2 ×

sub-PSU, no redundancy

2 × NEPS3500-A enclosure + 3 ×

sub-PSU, 2+1 redundancy

2 × NEPS3500-A enclosure + 4 ×

sub-PSU, 2+2 redundancy backup

2400 W (90 V to 180 V)

3500 W (180 V to 264 V)

NEPS3500-A

2 × NEPS3500-A enclosure + 3 ×

sub-PSU, no redundancy

2 × NEPS3500-A enclosure + 4 ×

sub-PSU, 3+1 redundancy

3500 W (90 V to 180 V)

z DC PSU

Table 1-3 Specifications for DC PSUs

Specifications

Item

NEPS1200-D NEPS2000-D NEPS3500-D

Model S9505 S9508/S9512 S9508/S9512

Rated

voltage

range

–48 to –60 VDC –48 to –60 VDC –48 to –60 VDC

Input

voltage

range

–36 to –72 VDC –36 to –72 VDC –36 to –72 VDC

Installation Manual

H3C S9500 Series Routing Switches Chapter 1 Product Overview

1-8

Specifications

Item

NEPS1200-D NEPS2000-D NEPS3500-D

Max

input

current

25 A 42 A 75 A

Max

output

power

1,200 W 2,000 W 3,500 W

1.2.4 PoE Power Supply

The S9500 series support power over Ethernet (PoE). With this feature, an S9500

switch equipped with an external PoE power supply and PoE-capable LPUs can deliver

–48 VDC to its remotely powered devices (PDs), such as IP phones, wireless LAN

(WLAN) access points (APs) and network cameras, through Ethernet cables.

Currently, among the LPUs of the S9500 series, only GV48 is PoE capable.

z The S9500 series can supply power to remote PDs through Ethernet electrical

ports on the LPUs. Each LPU can simultaneously supply power to up to 48 PDs

with the maximum distance of 100 m (328.1 feet).

z Each Ethernet port can deliver up to 15.4 W to its PD.

z The S9500 series determine whether to deliver power to a newly detected PD

according to the following condition: If the remaining PoE power of the switch is

greater than what is required by a newly detected PD, the switch supplies power to

it. Otherwise, the switch does not supply power to it.

I. PoE power entry module

The PoE-supported S9505/S9508/S9508V/S9512 switch chassis has a PoE power

entry module between the two PSUs. You can connect this PoE power entry module to

an external PoE power supply PSE4500-A.

Figure 1-5 PoE power entry module

Installation Manual

H3C S9500 Series Routing Switches Chapter 1 Product Overview

1-9

II. External PoE power supply

The S9505/S9508/S9508V/S9512 uses the PSE4500-A power system as an external

PoE power supply.

Figure 1-6 shows the PSE4500-A front panel.

Figure 1-6 PSE4500-A front panel

Table 1-4 describes typical equipment configurations and specifications of PSE4500-A.

Table 1-4 Typical equipment configurations and specifications of PSE4500-A

Item Specifications

Physical dimensions (H × W × D)

175 × 482.6 × 320.5 mm (6.89 × 19.00 × 12.62

in.)

System controller One

Rectifiers (NP2500UAC)

Two NP2500UACs (required) + one redundant

NP2500UAC (optional); NP2500UAC is

hot-swappable

AC accessories

Three AC inputs and switches

Three AC voltage detection circuits

Input voltage range: 90 to 264 VAC

DC accessories

A single DC output, with a max output power of

4500 W (220 V)/2400 W (110 V)

The external PoE power system has the monitoring function. It provides one RS232

and two RS485 monitoring interfaces. The external PoE power supply can display

alarm information through the ALM LED. The system can learn the running information

of the rectifiers by connecting a monitoring port to the SRPU. You can use cables to

connect the monitoring ports from the front or the rear of the external PoE power

supply.

Installation Manual

H3C S9500 Series Routing Switches Chapter 1 Product Overview

1-10

 Note:

The external PoE power system for the S9500 series only support RS485 monitoring

ports.

Table 1-5 LEDs of external PoE power system

LED Label Color

Normal

state

Abnormal

state

Abnormal reason

Input power

LED

AC Green ON OFF

Loss of AC input

power, or blown fuse

Output

power LED

DC Green ON OFF

No DC output from

PSU

Fault LED Fault Red OFF ON

Irreversible fault

occurred in PSU

Running

status LED

RUN Green ON OFF

PSU shutdown or

PSU running trouble

Alarm LED ALM Red OFF ON

Loss of AC input

power, under-voltage

or over-voltage input,

over-voltage output,

output short-circuit,

or PSU fault

1.2.5 Fan Tray

z The S9505 uses one 25 W fan tray, which contains four 120 × 120 × 25.4 mm (4.7

× 4.7 × 1.0 in.) DC fan units.

z The S9508 uses one 35 W fan tray, which contains six 120 × 120 × 25.4 mm (4.7 ×

4.7 × 1.0 in.) DC fan units.

z The S9508V uses one 70 W fan tray, which contains six 120 × 120 × 38 mm (4.7 ×

4.7 × 1.5 in.) DC fan units.

z The S9512 uses two 25 W fan trays, each of which contains four 120 × 120 × 25.4

mm (4.7 × 4.7 × 1.0 in.) DC fan units.

The fans of the S9505/S9508/S9508V/S9512 operate at –48 VDC supplied from the

backplane.

Installation Manual

H3C S9500 Series Routing Switches Chapter 1 Product Overview

1-11

Figure 1-7 Fan tray panel of the S9505/S9508/S9512

Figure 1-8 Fan tray panel of the S9508V

Table 1-6 LEDs on fan tray panel

LED Color Status Meaning

OFF The fan tray is faulty.

RUN Green

ON The fan tray is operating normally.

OFF The fan tray is operating normally.

ALM Red

ON The fan tray is faulty.

1.3 Switching and Routing Processing Unit

SRPUs serve as the core of the S9500 series. They mainly have the following

functions:

z Route calculation and forwarding table maintenance.

z Integrating crossbar switching fabric to accomplish service exchange between

different boards.

z Providing system configuration and monitoring functions, which allows the system

to monitor other boards and upgrade/reset service board software.

The following table lists the SRPUs applicable to the S9500 series.

Installation Manual

H3C S9500 Series Routing Switches Chapter 1 Product Overview

1-12

Table 1-7 SRPUs applicable to the S9500 series

SRPU S9505 S9508 S9508V S9512

LSB1SRP1N4

9

LSB1SRP1N5

9

LSB1SRP1N6

9

LSB1SRP1N7

9

LSB1SRP2N4

9

LSB1SRP2N5

9

LSB1SRP2N6

9

LSB1SRP2N7

9

LSB2SRP2N4

9

LSB2SRP2N5

9

LSB2SRP2N6

9

LSB2SRP2N7

9

 Note:

The tick 9 indicates that the SRPU is applicable to the switch. SRP2N’s forwarding

capacity is twice the SRP1N’s.

1.4 Line Processing Unit

The following LPUs are available:

Table 1-8 LPUs available

LPU Suffix User interface

LSB1FP20 B0, CA0 20 × 100 Mbps SFP/LC optical ports

LSB1F32G B0, CA0

4 × 1000 Mbps SFP/LC optical ports and 32 ×

auto-sensing 10/100 Mbps RJ-45 ports

LSB1FT48 B0 48 × auto-sensing 10/100 Mbps RJ-45 electrical ports

LSB2FT48 CA0 48 × auto-sensing 10/100 Mbps electrical ports

LSB1GP12

B0, CA0,

DB0

12 × 1000 Mbps SFP/LC optical ports

LSB1GP24

B0, CA0,

CB0, DB0,

DC0

24 × 1000 Mbps SFP/LC optical ports

Installation Manual

H3C S9500 Series Routing Switches Chapter 1 Product Overview

1-13

LPU Suffix User interface

LSB2GP24 DB0, DC0 24 × 1000 Mbps SFP/LC optical ports

LSB1GP48 DB0

48 × 1000 Mbps SFP/LC optical ports (1:4

convergence)

LSB1GP48L DB0 48 × 1000 Mbps SFP/LC optical ports (wire-speed)

LSB1GV48 DB0

48 × auto-sensing 10/100/1000 Mbps RJ-45

electrical ports (PoE-capable)

LSB2GV48 DB0

48 × auto-sensing 10/100/1000 Mbps RJ-45

electrical ports (PoE-capable)

LSB1GT24

B0, CA0,

DB0

24 × auto-sensing 10/100/1000 Mbps RJ-45

electrical ports

LSB2GT24 DB0

24 × auto-sensing 10/100/1000 Mbps RJ-45

electrical ports

LSB1GT48L DB0

48 × auto-sensing 10/100/1000 Mbps RJ-45

electrical ports (wire-speed)

LSB1P4G8 CA0

8 × 1000 Mbps SFP/LC optical ports and 4 × OC-3c

SFP/LC POS optical ports

LSB1GT8P CA0

4 × 1000 Mbps SFP/LC optical ports and 8 ×

auto-sensing 10/100/1000 Mbps RJ-45 ports

LSB1XP2

B0, CA0,

CB0, DB0,

DC0

2 × 10GBase-R XFP/LC/10GBase-W XFP/LC optical

ports

LSB1XP4

B0, CA0,

DB0

4 × 10GBase-R XFP/LC/10GBase-W XFP/LC optical

ports (1:2 convergence)

LSB1XP4L DB0

4 × 10GBase-R XFP/LC/10GBase-W XFP/LC optical

ports (wire-speed)

LSB1XP4T DB0

4 × 10GBase-R XFP/LC/10GBase-W XFP/LC optical

ports

LSB1XK1

B0, CA0,

DB0

1 × 10GBase-R XENPAK/SC port

LSB1SP4 CA0 4 × OC-48c SFP/LC POS optical ports

LSB1UP1 CA0 1 × OC-192c XFP/LC POS optical port

LSB1VP2 CA0 2 × OC-192c XFP/LC RPR optical ports

LSB1RSP2 CA0 2 × OC-48c SFP/LC RPR optical ports

Installation Manual

H3C S9500 Series Routing Switches Chapter 1 Product Overview

1-14

 Note:

The first column and the second column in the above table form an LPU model, for

example, LSB1XP2B0.

1.5 Service Board

Each kind of service board is specially designed for high-speed processing of a certain

service and has partial or no functions of LPU.

Currently, the following service boards are available:

z LSB1NATB0: for NAT service, no service port

z LSB1VPNB0: for VPLS service, no service port

z LSB1NAMB0: for NAM service, no service port

 Note:

For detailed specifications for the SRPUs, LPUs, and service boards, visit the website

at www. h3c.com.

1.6 System Specifications

The following table summarizes the physical specifications of the S9500 series.

Table 1-9 Technical specifications of the S9500 series

Item S9505 S9508 S9508V S9512

Dimensions

(H × W × D)

486 × 436 ×

450 mm (19.1

× 17.2 × 17.7

in.)

619 × 436 × 450

mm (24.4 × 17.2

× 17.7 in.)

888 × 436 ×

450 mm (35 ×

17.2 × 17.7

in.)

753 × 436 × 450

mm (29.6 × 17.2

× 17.7 in.)

Weight (full

load)

≤ 65 kg (143

lb)

≤ 80 kg (176 lb)

≤ 90 kg

(198.4 lb)

≤ 100 kg (220

lb)

Max power

consumption

1,200 W 2,000 W 2,000 W

2,000 W/3,500

W

Overall

switching

capacity

SRP1N6:

300 Gbps

SRP2N6: 600

Gbps

SRP1N5:

480 Gbps

SRP2N5:

960 Gbps

SRP1N5:

480 Gbps

SRP2N5:

960 Gbps

SRP1N4:

720 Gbps

SRP2N4:

1.44 Tbps

Number of

VLANs

4 K

Page is loading ...

3com S9508V, S9505, S9505 SRP, S9508 FABRIC, S9512 FABRIC Installation guide

Related papers

Other documents