BLACK+DECKER GL430S Owner's manual

Page is loading ...

2

English 5

Deutsch 12

Français 19

Italiano 26

Nederlands 33

Español 40

Português 47

EÏÏËÓÈÎ· 53

Copyright Black & Decker

Page is loading ...

5

ENGLISH

STRIMMER GL420/GL425/GL430

INTENDED USE

Your Black & Decker strimmer GL420/GL425/GL430

families has been designed for trimming lawn

edges and to cut grass in confined spaces.

This tool is intended for consumer use only.

SAFETY INSTRUCTIONS

Warning symbols

The following symbols are used in this manual:

Denotes risk of personal injury, loss of life

or damage to the tool in case of non-

observance of the instructions in this

manual.

Denotes risk of electric shock.

Read the manual prior to operation.

Know your appliance

◆ Warning! When using mains-powered

appliances, basic safety precautions,

including the following, should always

be followed to reduce the risk of fire,

electric shock and personal injury.

◆ Read all of this manual carefully before

operating the appliance.

◆ Before operating the appliance, make

sure that you know how to switch it off

in an emergency.

◆ The intended use is described in this

manual. The use of any accessory or

attachment or performance of any

operation with this appliance other than

those recommended in this instruction

manual may present a risk of personal

injury.

◆ Retain this manual for future reference.

CONGRATULATIONS!

You have chosen a Black & Decker tool. Our aim is

to provide quality tools at an affordable price.

We hope that you will enjoy using this tool for

many years

EC DECLARATION OF CONFORMITY

GL420/GL425/GL430 families

Black & Decker declares that these

products conform to: 98/37/EC,

89/336/EEC, 73/23/EEC, EN 60335,

EN 55014, EN 61000

Level of sound pressure, measured according to

84/538/EEC:

L

pA

(sound pressure) dB(A) 83

L

WA

(acoustic power) dB(A) 96

Always wear ear protection if the sound

pressure exceeds 85 dB(A).

Hand/arm weighted vibration value according to

98/37/EC:

< 2.5 m/s

2

Brian Cooke

Director of Engineering

Spennymoor, County Durham DL16 6JG,

United Kingdom

6

ENGLISH

Work area

◆ Do not expose the appliance to rain. Do not

use the appliance in damp or wet conditions.

◆ Only use the appliance in daylight or good

artificial light.

Personal protection

◆ Wear stout shoes or boots to protect your feet.

Do not operate the appliance wearing open-

toed sandals or when barefoot.

◆ Wear long trousers to protect your legs.

Using your appliance

◆ Be sure that the appliance is switched off when

plugging in.

◆ Stay alert. Watch what you are doing.

Use common sense.

◆ Do not operate the appliance when you are

tired.

◆ If the appliance begins to vibrate abnormally,

switch it off and remove the plug from the

socket. Allow rotating parts to stop and inspect

the appliance for damage and loose parts.

◆ Never pull the cord to disconnect the plug

from the socket. Keep the cord away from

heat, oil and sharp edges.

◆ If the mains cable is damaged during use,

switch the appliance off and disconnect the

plug from the mains immediately. Do not

touch the mains cable before disconnecting

from the mains.

Safety of others

◆ Do not allow children or any person unfamiliar

with these instructions to operate the appliance.

◆ Do not allow children, visitors or animals to

come near the work area or to touch the

appliance or mains cable.

◆ Remember that the operator may be held

responsible for accidents or hazards occurring

to other people or their property.

After use

◆ Switch off, remove the plug from the socket

and ensure that moving parts have stopped

rotating before leaving the appliance

unattended and before changing, cleaning or

inspecting any parts of the appliance.

◆ When not in use, the appliance should be

stored in a dry place. Children should not have

access to stored appliances.

Inspection and repairs

◆ Before use, check the appliance for damaged

or defective parts. Check for misalignment and

seizure of moving parts, breakage of parts,

damage to guards and switches and any other

conditions that may affect its operation.

◆ Do not use the appliance if any part is damaged

or defective. Do not use the appliance if the

switch does not turn it on and off.

◆ Never use the appliance when any guard or

enclosure is damaged or not in place.

◆ Ensure that the appliance will operate properly

and perform its intended function.

◆ Have any damaged or defective parts repaired

or replaced by an authorised repair agent.

◆ Before use, check the mains cable for signs of

damage, ageing and wear.

◆ Do not use the appliance if the mains cable is

damaged or defective.

◆ If the mains cable is damaged or defective it

must be repaired by an authorised repair agent

to avoid a hazard.

◆ Never attempt to remove or replace any parts

other than those specified in this manual.

Additional safety instructions for grass trimmers

The following warning symbols are found on the

appliance:

Wear safety glasses or goggles when

operating this tool.

The cutting line will continue to run for a

few seconds after switching the appliance

off. Never attempt to force the line to

come to a standstill.

360˚

6m/20ft

Keep people and animals at least 6 m

away from the cutting area.

Do not expose the appliance to rain or

high humidity.

7

ENGLISH

Switch off, remove the plug from the

socket and ensure that moving parts have

stopped rotating before leaving the

appliance unattended and before

changing, cleaning or inspecting any parts

of the appliance.

◆ Before using the appliance, check that your

cutting path is free from sticks, stones, wire

and any other objects.

◆ Only use the appliance in the correct position,

with the cutting line near the ground, as shown

in the illustrations. Never switch the appliance

on in any other position.

◆ Switch on the appliance only when hands and

feet are away from the cutting line.

◆ Avoid body contact with the cutting line while

the appliance is running.

◆ Do not work on steep slopes. Be sure of your

footing. Be aware that freshly cut grass is

damp and slippery.

◆ Take care when trimming near borders and

gravel paths or roads, as stones and soil may

be moved by the cutting line.

◆ Do not put the appliance down until the

cutting line has come to a complete standstill.

◆ Use only the appropriate type of

Black & Decker cutting line. Never use metal

cutting line or fishing line.

◆ Take care to avoid injury from the line

trimming blade. Do not touch the blade.

After extending new cutting line, always return

the appliance to its normal operating position

before switching on.

◆ Take care to keep the mains cable away from

the cutting line. Always be aware of the

position of the cable.

ELECTRICAL SAFETY

The appliance has been designed for one voltage

only. Always check that the power supply

corresponds to the voltage on the rating plate.

This appliance is designed for use on AC

(mains) power supplies only. Do not

attempt to use on any other supply.

This appliance is double insulated in

accordance with EN 60335; therefore

no earth wire is required.

◆ Prevent body contact with earthed or

grounded surfaces (e.g. metal railings,

lamp-posts etc.).

◆ Electric safety can be further improved by

using a high-sensitivity (30 mA/30 mS) residual

current device (RCD).

Mains plug replacement (U.K. & Ireland only)

◆ Should your mains plug need replacing and

you are competent to do this, proceed as

instructed below. If you are in doubt, contact

an authorised repair agent or a qualified

electrician.

◆ Disconnect the plug from the supply and

remove the fuse from the plug.

◆ Cut off the plug and dispose of it safely; a plug

with bared copper conductors is dangerous if

engaged in a live socket outlet.

◆ Only fit 13 Amperes BS1363A approved plugs

fitted with the correctly rated fuse (1).

Use 5 Amperes fuses.

◆ The cable wire colours, or a letter, will be marked

at the connection points of most good quality

plugs. Attach the wires to their respective points

in the plug (see above).

Brown is for Live (L) (2), blue is for Neutral (N) (4).

◆ Before replacing the top cover of the mains

plug ensure that the cable restraint (3) is holding

the outer sheath of the cable firmly and that the

leads are correctly fixed at the terminal screws.

◆ If the plug has a fuse cover, make sure that the

fuse cover is fitted. Do not use the plug if the

fuse cover is missing or damaged.

8

ENGLISH

Never use a light socket.

Using an extension cable

Always use an approved extension cable suitable

for the power input of this appliance (see rating

plate). The extension cable must be suitable for

outdoor use.

◆ Before use, inspect the cable for signs of

damage, wear and ageing. Replace the

extension cable if damaged or defective.

◆ When using a cable reel, always unwind the

cable completely.

◆ Take care to keep the cable away from the

cutting line. Always be aware of the position of

the cable.

CARTON CONTENTS

The carton contains:

1 Grass trimmer

1 Guard with mounting screw

1 Instruction manual

◆ Carefully unpack all parts.

OVERVIEW (fig. A)

1. On/off switch

2. Handle

3. Power inlet (not for UK)

3. Mains cable (UK)

4. Secondary handle (GL430)

5. Guard

6. Line trimming blade

7. Spool housing

8. Cutting line

ASSEMBLY

Before assembly, make sure that the tool

is switched off and unplugged.

Fitting the guard (fig. B)

◆ Unplug the tool.

◆ Remove the screw (9) from the guard (5).

◆ Place the guard (5) onto the tool as shown.

◆ Firmly press the guard until it snaps into place.

◆ Secure the guard with the screw (9).

Never use the tool unless the guard is

properly fitted.

Releasing the cutting line (fig. A)

In transit, the cutting line is taped to the spool

housing.

◆ Remove the tape holding the cutting line (8) to

the spool housing (7).

Connecting the tool to the mains (fig. A & C)

Unless the tool is fitted with a mains cable, you will

need to connect an extension cable to the power

inlet (3).

◆ Connect the female socket of a suitable

extension cable to the power inlet (3).

◆ Loop the cable through the cable restraint (10)

as shown to prevent the extension cable from

becoming detached during use.

◆ Insert the mains plug into a mains outlet.

The extension cable must be suitable for

outdoor use.

USE

Let the tool work at its own pace. Do not

overload.

Switching on and off (fig. A)

◆ To switch the tool on, push the on/off switch (1).

◆ To switch the tool off, release the the on/off

switch.

Never attempt to lock a switch in the on

position.

Automatic line feed

The Reflex system will automatically feed out more

cutting line when necessary.

Hints for optimum use

◆ Hold the tool as shown in fig. F.

◆ Gently swing the trimmer from side to side as

shown in fig. F.

◆ When cutting long grass, work in stages from

the top.

◆ Keep the tool away from hard objects and

delicate plants.

9

ENGLISH

◆ If the tool starts running slowly, reduce the load.

◆ In order to achieve optimum cutting results,

only cut dry grass.

MAINTENANCE

Your Black & Decker tool has been designed to

operate over a long period of time with a

minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and

regular cleaning.

Before performing any maintenance,

switch off and unplug the tool.

◆ Regularly clean the ventilation slots in your tool

using a soft brush or dry cloth.

◆ Regularly clean the cutting line and spool

using a soft brush or dry cloth.

◆ Regularly use a blunt scraper to remove grass

and dirt from the underneath of the guard.

Do not use any abrasive or solvent-based

cleaner.

Fitting a new spool of cutting line (fig. D)

Replacement spools of cutting line are available

from your Black & Decker dealer (cat. no. A6481).

◆ Unplug the tool.

◆ Keep the tabs (11) depressed and remove the

spool cover (12) from the housing (7).

◆ Remove the empty spool (13) from the housing.

◆ Remove any dirt and grass from the housing.

◆ Take the new spool and unwind approx.

9 cm of cutting line.

◆ Feed the cutting line through the eyelet (14).

◆ Push the spool onto the drive shaft (15) and

rotate it slightly until it is seated. Make sure

that the cutting line is not trapped under the

spool and that 9 cm of cutting line protrudes

from the housing.

◆ Align the tabs on the spool cover with the

holes in the housing.

◆ Push the cover onto the housing until it snaps

securely into place.

If the cutting line protrudes beyond the

trimming blade (6), cut it off so that it just

reaches the blade.

Winding new line onto an empty spool (fig. E)

You may wind new cutting line onto an empty

spool. Replacement packs of cutting line are

available from your Black & Decker dealer

(cat. no. A6170 (25 m), A6171 (40 m)).

◆ Remove the empty spool from the tool as

described above.

◆ Remove any old cutting line from the spool.

◆ Feed 2 cm of cutting line into one of the holes

(16) in the spool as shown.

◆ Bend the cutting line and anchor it in the

L-shaped slot (17).

◆ Wind the cutting line onto the spool in the

direction of the arrow (18). Make sure to wind

the line on neatly and in layers.

Do not criss-cross.

◆ When the wound cutting line reaches the

recesses (19), cut the line. Let the line protrude

approx. 9 cm from the spool and hold a finger

on the line to keep it in place.

◆ Proceed as described above to fit the spool on

the tool.

Only use round 1.5 mm diameter

Black & Decker cutting line. Do not use

Reflex Plus twisted cutting line. The use of

an incorrect type of cutting line can damage

the auto feed mechanism and will void the

warranty.

TROUBLESHOOTING

If your tool seems not to operate properly,

follow the instructions below. If this does not solve

the problem, please contact your local

Black & Decker repair agent.

Before proceeding, unplug the tool.

Tool does not start

◆ Check that the power cables are properly

connected.

◆ Check the mains fuses.

Tool vibrates strongly

◆ Carefully clean the spool housing.

◆ If this does not solve the problem, unwind the

line from the spool and rewind it more tightly.

10

ENGLISH

Tool runs slowly

◆ Check that the spool housing can rotate freely.

Carefully clean it if necessary.

◆ Check that the cutting line does not protrude

more than 9 cm from the spool housing.

If it does, cut it off so that it just reaches the

line trimming blade.

Automatic line feed does not work

◆ Keep the tabs depressed and remove the

spool cover from the housing.

◆ Lift the spool approx. 6 mm and pull the

cutting line until it protrudes 9 cm from the

housing. If insufficient cutting line is left on

the spool, install a new spool of cutting line as

instructed above.

◆ Push the spool back into place and rotate it

slightly until it is seated.

◆ Align the tabs on the spool cover with the

holes in the housing.

◆ Push the cover onto the housing until it snaps

securely into place.

◆ If the cutting line protrudes beyond the trimming

blade, cut it off so that it just reaches the blade.

If the automatic line feed still does not work or the

spool is jammed, try the following suggestions:

◆ Carefully clean the spool cover and housing.

◆ Remove the spool and check if the lever (20)

can move freely (fig. D).

◆ Remove the spool and unwind the cutting line,

then wind it on neatly again as described

above. Replace the spool as instructed.

PROTECTING THE ENVIRONMENT

Should you find one day that your tool

needs replacement, or if it is of no further

use to you, think of the protection of the

environment. Black & Decker repair agents

will accept old Black & Decker tools and

ensure that they are disposed of in an

environmentally safe way.

GUARANTEE

The Black & Decker lawn and garden guarantee

provides: 36 months parts and 12 months

labour cover in the UK, 24 months parts and

labour cover in South Africa, Australia and New

Zealand. Proof of purchase will be required.

Should your Black & Decker product become

defective within the guarantee period due to

faulty materials or workmanship, we guarantee to

either replace all defective parts or -at our

discretion- to replace the unit free of charge,

provided that:

◆ The product is returned to us or one of our

authorised repair agents with proof of purchase.

◆ The product has been used within the

parameters of its consumer classification.

◆ The product has not been used for hire

purposes.

◆ Repairs have not been attempted by anyone

other than our authorised repair agents.

◆ The failure represents normal wear and tear.

This guarantee is offered as an extra benefit and

does not affect your statutory rights.

The guarantee policy

The following failures are not covered by the

above guarantee:

◆ Replacing worn or damaged blades,

nylon lines, chains and power cables.

These items are regarded as replacement

items which wear during normal usage.

◆ Failures as a result of sudden impact or

obvious abuse.

◆ Failures due to usage not in accordance with

instructions and recommendations contained

in this manual.

The use of other than genuine Black & Decker

accessories and parts may cause decreased

performance or damage to the product and will

render the guarantee void.

AFTER SALES SERVICE

Full details on our after-sales service are available

on the Internet at www.2helpU.com.

Alternatively, contact our Service and Information

Centre at the address towards the back of this

manual.

11

ENGLISH

It is our aim that all Black & Decker customers

should be totally satisfied with their

Black & Decker product and our after sales service.

If any help or advice is needed, please contact

your local Black & Decker repair agent.

If your product needs repair, please take or send it

to an authorised repair agent, providing proof of

purchase if claiming a guarantee repair.

Black & Decker offers a nationwide network of

authorised repair agents.

Full details on our after sales service can be

obtained from any of our authorised repair agents.

OTHER OUTDOOR TOOLS

Black & Decker has a full range of outdoor power

tools that make life in the garden easy. If you

would like further information on the following

products, please contact our Service and

Information Centre (see the address page towards

the end of this manual) or your local

Black & Decker retailer.

String trimmers Chainsaws

Cordless shear Hedgetrimmers

Lawnmowers Lawnrakers

Leafbusters Shredders

Not all products are available in all countries.

Page is loading ...

61

TYP.

E13003 24 - 07 - 2000

1

GL20S/GL225/GL420/GL425

GL20S GL20SC

GL225/225S/225SC/225C

GL420/GL425/425S/425SC

2

3

4

5

6

7

8

9

10

11

12

15

16

23

17

18

22

1

19

20

21

1

13

14

www.2helpU.com

6

13

62

TYP.

E13002

www.2helpU.com

24 - 07 - 2000

1

GL430

1

19

20

21

2

4

8

9

7

5

10

6

12

3

24

13

14

6

11

23

15

16

13

Page is loading ...

verktøj? Onko tämä ensimmäinen

B&D-koneesi?

Yes Ja Oui Si Ja Sí

Sim Ja Ja Ja Kyllä

No Nein Non No Nee

No Não Nej Nei Nej

Ei

Dealer address Händleradresse

Cachet du revendeur Indirizzo del

rivenditore Adres van de dealer

Dirección del detallista Morada do

revendedor Återförsäljarens adress

Forhandlerens adresse Forhandler

adresse Jälleenmyyjän osoite

............................................................

Is this tool a gift? Ist dieses Gerät

ein Geschenk? S’agit-il d’un cadeau?

Si tratta di un regalo? Kreeg u de

machine als cadeau? ¿Ha recibido

usted esta herramienta como regalo?

Recebeu esta ferramenta como

presente? Är verktyget en gåva?

Er verktøyet en gave? Er verktøjet

en gave? Onko kone lahja?

Yes Ja Oui Si Ja Sí

Sim Ja Ja Ja Kyllä

No Nein Non No Nee

No Não Nej Nei Nej

Ei

Is this tool your first purchase? Ist

dieses Gerät ein Erstkauf? Est-ce un

1er achat? Questo prodotto è il suo

primo acquisto? Is deze machine uw

eerste aankoop? ¿Es esta

herramienta la primera de este tipo?

Esta ferramenta é a sua primeira

compra? Är detta ditt första B&D-

verktyg? Er dette ditt første B&D

verktøy? Er dette dit første B&D

Dealer address Date of purchase

Händleradresse Kaufdatum

Cachet du revendeur Date d’achat

Indirizzo del rivenditore Data d’acquisto

Adres van de dealer Aankoopdatum

Dirección del detallista Fecha de compra

Morada do revendedor Data de compra

Återförsäljarens adress Inköpsdatum

Forhandlerens adresse Innkjøpsdato

Forhandler adresse Indkøbsdato

Jälleenmyyjän osoite Ostopäivä

Name Name Nom Nome

Naam Nombre Nome Namn

Navn Navn Nimi :

............................................................

Address Adresse Adresse

Indirizzo Adres Dirección Morada

Adress Adresse Adresse Osoite

:

............................................................

Town Ort Ville Cittá Plaats

Ciudad Localidade Ort By By

Paikkakunta :

............................................................

Postal code Postleitzahl Code

postal Codice postale Postcode

Código Código postal Postnr.

Postnr. Postnr. Postinumero

............................................................

Data protection act: Tick the box if

you prefer not to receive further

information. Bitte ankreuzen, falls Sie

keine weiteren Informationen erhalten

möchten. Si vous ne souhaitez pas

recevoir d’informations, cochez cette

case. Barrate la casella se non

desiderate ricevere informazioni.

A.u.b. dit vakje aankruisen indien u

geen informatie wenst te ontvangen.

Señale en la casilla sino quiere recibir

información. Por favor, assinale com

uma cruz se não desejar receber

informação. Vänligen kryssa för i

rutan om Ni inte vill ha information.

Vennligst kryss av dersom du ikke

ønsker informasjon. Venligst sæt

kryds i ruden såfremt De ikke måtte

ønske at modtage information.

Merkitkää rasti ruutuun, mikäli ette

halua vastaanottaa informaatiota.

Después de haber comprado su herramienta envíe

usted, por favor, esta tarjeta a la central de

Black & Decker en su país.

Por favor, recorte esta parte, coloque-a num envelope

selado e endereçado e envie-o logo após a compra do

seu produto para o endereço da Black & Decker do

seu país.

Var vänlig klipp ur denna del och sänd den i ett frankerat

kuvert till Black & Deckers adress i Ditt land.

Vennligst klipp ut denne delen umiddelbart etter du

har pakket ut ditt produkt og legg det i en adressert

konvolutt til Black & Decker (Norge) A/S.

Venligst klip denne del ud og send frankeret til

Black & Decker i dit land.

Leikkaa irti tämä osa, laita se kuoreen ja postita kuori

paikalliseen Black & Decker osoitteeseen.

.

Please complete this section immediately after the

purchase of your tool and send it to Black & Decker in

your country. If you live in Australia or New Zealand,

please register by using the alternative guarantee card

supplied.

Bitte schneiden Sie diesen Abschnitt ab, stecken ihn in

einen frankierten Umschlag und schicken ihn an die

Black & Decker Adresse Ihres Landes.

Découpez cette partie et envoyez-la sous enveloppe

timbrée à l’adresse de Black & Decker dans votre pays,

ceci immédiatement après votre achat.

Per favore ritagliate questa parte, inseritela in una

busta con francobollo e speditela subito dopo

l’acquisto del prodotto all’indirizzo della

Black & Decker nella vostra nazione.

Knip dit gedeelte uit en zend het direct na aankoop in

een gefrankeerde, geadresseerde envelop naar het

adres van Black & Decker in uw land.

574792-07

BLACK+DECKER GL430S, GL425S T2 Owner's manual

Related papers

Other documents