Page is loading ...
ampire
WFS300-BT
German Engineering. Out of the ordinary.
Owner’s Manual
Bitte lesen Sie die komplette Anleitung aufmerksam durch, bevor Sie mit der Installation beginnen.
Before attempting to connect or operate this product, please read the instructions completely.
1. Make sure the ignition is on and the WFS300-BT system is in the leran mode
(Every 3 seconds, the system displays an indicator signal in the vehicle interior).
2. Enter the PIN code using the buttons (see list of buttons that can be used). Each press of the
button is confirmed with a display signal. The PIN code must be At least 3 and a maximum of 20
keys. By the car brand INFINITI, at least 2 Various keys are pressed. The breaks between pressing
the buttons, should not be Longer than 2 seconds. It does not differentiate from quick or long
presses. The following combination is possible, for example: 2 times " CRUISE ON /
OFF" press and 1 time " CRUISE SET" . The WFS300-BT will then store the sequence, and confirm with
3 flashes if the PIN is accepted.
3. Re-enter the PIN code. If the PIN code is repeated correctly, then the system will confirm with 2
lashes. IF you get 4 flashes, it did not match. Please repeat steps 1-3.
4. Turn the ignition off.
5. Disconnect the gray cable from " permanent" .
ATTENTION! It is recommended to change the PIN code after the vehicle has been picked up by the
installation workshop.
Setting the PIN code
Introduction
Congratulations! You have purchased the latest in high-end vehicle security. The WFS300-BT is a
revolutionary immobiliser that is the first of its kind in the world. This immobiliser not only delivers
incredibly high security but it also does this without the need for any unsightly key fobs or remotes.
The WFS300-BT uses the myriad of buttons already in your vehicle to provide you with a secret PIN
code without which not even a thief with a key could get away with your vehicle.
Where other immobilisers and tracking systems can be found or jammed the WFS300-BT remains
hidden and secure.
2
Electronics Irrtum und technische Änderungen vorbehalten–
ampire
10.2016
EN
If the current PIN code is lost, it can be reset and a new one can be assigned. You need the plastic card
with the emergency code to reset the PIN code. This card is included with the WFS300-BT system.
1. Switch on ignition, do not start engine.
2. Press and hold the brake pedal, press and release the accelerator pedal the number of times matching
the first digit of the PIN to the first digit of the emergency code (indicated on the plastic card). Release
brake pedal. The first digit has now been entered.
3. Enter the remaining digits of the emergency code in the same way. If the
Emergency code has been entered correctly, the device switches to the PIN change mode and
illuminates the indicator for 3 seconds'. If nothing happens, this means that the code is incorrect Is
entered. In this case, switch off the ignition and repeat the procedure. If The reset is completed
successfully, enter the new PIN code. The number of Key press must be from 3 to 20. By the car brand
INFINITI, at least 2 different Buttons. If a valid PIN code has been entered, tYou will get confirmation
with 3 flashes of the signal. Enter the PIN code again. If the second entry matches, you will get a
confirmation of 2 flashes'. The device saves the new code and changes to the Normal operation. If the
entered PIN code does not match, the signal is 4 times. In this case, the process must be repeated from
the beginning (point 1).
* Some vehicles you are not able to program the PIN via the accelerator pedal. The vehicle list will
highlight this for you.
Resetting the PIN code
The procedure for entering the PIN code depends on the selected method.
• If a start ban is used, the PIN code must be set before starting the Motor.
• If no start prohibition is used, the PIN code can be used both before and after starting the engine.
Sit behind the steering wheel, turn on the ignition, start the engine, if necessary, and enter the PIN code
using the preset buttons. It is recommended to enter the PIN code before starting. The break between the
buttons should not be longer than 2 seconds. There is no difference between long and short pressing of
the keys. When the PIN code is entered correctly, the system will output 2 times a signal and you can
start driving. If the PIN code is entered incorrectly, then you do not get a signal as confirmation. When
starting or Driving, the motor is blocked. Re-entering the PIN code is possible 5 seconds after a failed
login attempt OR switch off the ignition, switch on again 3 seconds later and try again.
Enter the PIN code
3
Electronics Irrtum und technische Änderungen vorbehalten–
ampire
10.2016
EN
Check the device number
It is recommended to change the PIN code after the WFS300-BT system has been installed by the dealer.
The PIN code change is also necessary if you suspect someone has spied the PIN code.
1. Switch on the ignition, do not start the engine.
2. Enter the PIN code, the display signal is flashes 2 times.
3. Press and hold the accelerator pedal * fully.
4. Re-enter the current PIN code. The system changes to the change mode, flashing every 3 seconds.
Release accelerator pedal.
5. Enter the new PIN code using the buttons. Each press of the button is confirmed with a Display signal
Flash. The number of key strokes must be from 3 to 20. By the car brand INFINITI, at least 2
different keys must be pressed. The breaks between the Pressing the buttons should not be longer
than 2 seconds. The following combination is possible, as an example: 2 times Press " CRUISE ON /
OFF" and " CRUISE SET" once. The system remembers the order of the 3 Pressed buttons. If a valid PIN
code has been entered, the system Confirms with 3 flashes.
6. Re-enter the PIN code. 2 flashes will confirm that the PIN matches. If the system outputs the display
signal 4 times, this means that the Entered PIN codes do not match. Switch off the ignition and repeat
Step 1 to 6.
7. Switch off the ignition.
ATTENTION! After the PIN code has been changed, remember or write it down. NEVER leave information
on the PIN code or the plastic card in the car.
* To enter the PIN code on some cars does not have the accelerator but something else
(See vehicle list).
4
Electronics Irrtum und technische Änderungen vorbehalten–
ampire
10.2016
Change the PIN code
This test is required to confirm the device number on the plastic card with the assigned system. If the
code on the card does not Match with the device, a forgotten PIN code can only be reset By an
approved installer. We recommend to carry out this test immediately, you collect your vehicle.
1. Switch on the ignition, do not start the engine.
2. Press and hold the brake pedal, tpress the accelerator to the floor And release it according
to the first digit of the device number (on The plastic card). Release the brake pedal. The first digit
was Now entered.
3. Enter the remaining digits from the plastic card in the same way. If the device number has been
entered correctly, you will be acknowledged with 2 display signals. If nothing happens, the number
is entered incorrectly or does not match the device number.
* To enter the PIN code, some cars do not have the accelerator, but something else
(See vehicle list).
EN
Options
Turn on
Turn off
Service mode
5
Automatic or with
Pin Code
Auto unlock when IGN off*
6
7
Closing the Speed controlled
locking From> 10 km /
8
9
Airing
10
11
Comfort
12
13
Folding of mirrors
14
15
Anti-Hijack
16
17
Start interruption**
18
19
additional options
20
21
The settings in the delivery status are grayed out. The numbers in the table correspond to the number
of times the service key is pressed to select this option.
* Automatic opening of ZV (central locking):
• for vehicles where the engine is started using the key. key off
Remove the ignition lock.
• for vehicles with «Start-Stop» button. Switch off the ignition.
** The default setting is dependent on the brand and model.
For some cars, additional options can be selected (see compatibility list), for example: automatic start
/ stop switch, change of the signal display and more. To change the setting at the desired point,
proceed as follows:
1. Switch on the ignition without starting the engine, enter the PIN code.
2. Press and hold the accelerator pedal *.
3. Press the service button repeatedly until the desired option is " Enabled" orEnabled " Off" was -““
(corresponding to number from the table). For example, 16 times Press to switch the Anti-Hijack
mode on or 17 times to get it Off. The display signal confirms the input of the selected option.
4. Release the accelerator pedal.
5
Electronics Irrtum und technische Änderungen vorbehalten–
ampire
10.2016
Change settings
EN
To connect the app to the car, perform the following steps:
1. Turn on Bluetooth on your smartphone.
2. Turn on the WFS300-BT App.
With WFS300-BT Systems, it is possible to use smartphone for automatic login. The user can log in
by entering the pin code or automatically with the app via Bluetooth from the smartphone.
This feature is available for the following Smartphone models:
• Apple iPhone 4S
• Apple iPhone 5
• Apple iPhone 5C
• Apple iPhone 5S
• Apple iPhone 6
• Apple iPhone 6S
• Apple iPhone 7
When using the smartphone for authorization, it is necessary to install the app
Use the app
6
Electronics Irrtum und technische Änderungen vorbehalten–
ampire
10.2016
Install the app
EN
3. Go to the «Settings» tab.
4. Press the «Connect to vehicle» key.
7
Electronics Irrtum und technische Änderungen vorbehalten–
ampire
10.2016
Use the App
5. Switch on the ignition.
6. Enter the PIN code.
7. Enter the " Change PIN Code“ By holding the accelerator
pedal (depending on the vehicle)The current pin code.
The system returns all 3 Seconds.
8. Press the service key once.
9. After carrying out the above steps, Press << Continue <<
on your smartphone.
EN
ATTENTION! For security reasons, you must delete the memory in the WFS300-BT system if the
phone is lost. To do this, the PIN code must be changed. The secret code to connect a new
smartphone remains the same.
ATTENTION! It is necessary that the Bluetooth on the smartphone is switched on.
11. Press the button in the center of the screen
" Authorization" to activate it. After that you can use
the smartphone over an encrypted channel For
authorization. Is working At a distance of 0.5 to 10
meters to the system. If the connection to the
WFS300-BT system has not worked, then The
connected devices must be removed. to establish
the connection between the system and Delete your
smartphone go to the Tab: Settings -> Bluetooth ->
Devices -> WFS300-BT -> Cancel pairing. After
Successful removal, the system enters 2 times
Display signal. We recommend this procedure
Immediately after losing the smartphone.
If only the phone is removed from the system, Then
you can also in the app " WFS300-BT" under
" Settings" .
8
Electronics Irrtum und technische Änderungen vorbehalten–
ampire
10.2016
Use the App
10. In the next window, enter the Secret code. The
smartphone will follow the Successful input with
the system connected.
EN
Electronics Irrtum und technische Änderungen vorbehalten–
ampire
10.2016
Space for Sketches
9
ATTENTION! Note the new PIN code after you have changed it. NEVER
leave the card with the emergency code or this manual in the vehicle!
Here you must draw the installation location of the WFS300-BT.
EN
10
Space for Sketches
Electronics Irrtum und technische Änderungen vorbehalten–
ampire
10.2016
EN
Space for Sketches
11
Electronics Irrtum und technische Änderungen vorbehalten–
ampire
10.2016
EN
ampire
WFS300-BT
Since its founding in 1987 Ampire Electronics has only one goal, to provide the best possible
Autoalarm-, Autohifi- and Multimedia products, which are available on the international
market.
All manufacturing facilities and suppliers are certified according to ISO 9001 and QS-9000.
Ampire quality products are sold worldwide.
An Ampire customer service is available in many countries.
For more information about distributors in your territory please call: + 49-2181-81955-0.
We are focused on future oriented development of user friendly products.
The outstanding high quality standards, functionalities and designs of our products are
unique in the market. " German Development" is taken literally in AMPIRE.
Langwadener Straße 60
D-41516 Grevenbroich
Support
+49 2181-81955-0
www.ampire.de
© 10.2016 AMPIRE ELECTRONICS. Alle Rechte vorbehalten. Nachdruck, auch auszugsweise, nur mit schriftlicher Genehmigung. /
All rights reserved. Reproduction in whole or in part without written permission.
/