Ampire PSA400C Installation guide

Type
Installation guide
ampire
PSA400C
German Engineering. Out of the ordinary.
Installation Manual
English
Before attempting to connect or operate this product, please read the instructions completely.
2
3
Installation of Sensors
Precautions
Warranty
Pay utmost attention if you install the parking sensor into the car.
To measure the voltage of vehicle’s wires please use only voltmeters or diode lamps.
Standard measurement lamps may have to much power consumption and will damage
the vehicle’s electronic.
All parts have to installed fasten and protected.
Arrange the wiring so it is not crimped or pinched by a sharp metal edge.
Do not damage pipe or wiring when drilling holes.
The parking sensor is only a support for the driver. It don’t release the driver to take
care while driving backwards.
Extreme deposit of dirt, ice and snow may reduce the value of function.
Don’t clean the sensors with vapour pressure cleaning machines.
12 month warranty for commercial use and 24 month warranty for private use only. The
location of buying (point of purchase) must be within the EU. The proof of warranty is the
original cashiers receipt with date and type of item on it. The owners manual and installation
instructions must be observed. No warranty of destruction by wrong installation, wrong
operation, non regulated use, using of unsuitable accessories, electrical shocks, fire,
moisture or smoke, damage by improper service and cleaning. Warranty repairs are free of
charge. No refund of shipping costs or labour as well as subsequent damages. Complaints
and repairs do not extend the warranty period.
Environmental Reference
Old electronic devices don’t belong into the bin.
If you want to dispose this equipment later, remove all
cables and send it back to Ampire.
You can dispose this device together with your old car, too.
You don’t have to remove it in this case.
The packing can be recycled. Dispose the packing in a
collecting system planned for it.
Electronics Subject to correction and technical modifications
ampire
2016
EN
The sensors should be installed 50-70cm over the
ground into the rear bumper.
The distance between the outside sensors should
be 126cm max.
To avoid wrong alarm or affecting the detecting
result, ensure no vehicle parts included in the
detection range at lateral angle of 90°.
The sensors must be fixed vertically, fixing up or
down may affect its performance.
The cable of sensors must point toward the
bottom.
To avoid collision or damage to sensors, the
sensor should be inserted completely into the
bumper and flush with the surface.
Stick the sick paper on the bumper then drill 4
holes in the selected position as the below.
To painting the sensors please stick the protective
ring onto the rubber ring of the sensors. Spray
paint on the sensor to achieve your desired colour
surface. Wait until the paint is dried off completely,
then detach the painting ring from the sensors and
throw it away.
Insert the ultrasonic detectors in the right order
(see 3. Installation Diagram) into the holes
separately and then fix them in right position.
Press the sensor with a slab, but not with fingers
directly to the avoid damaging the sensors.
The buzzer should be placed where the driver can hear the sound clearly.
Installation of Buzzer
Electronics Subject to correction and technical modifications
ampire
2016
EN
2
3
Installation of Sensors
Precautions
Warranty
Pay utmost attention if you install the parking sensor into the car.
To measure the voltage of vehicle’s wires please use only voltmeters or diode lamps.
Standard measurement lamps may have to much power consumption and will damage
the vehicle’s electronic.
All parts have to installed fasten and protected.
Arrange the wiring so it is not crimped or pinched by a sharp metal edge.
Do not damage pipe or wiring when drilling holes.
The parking sensor is only a support for the driver. It don’t release the driver to take
care while driving backwards.
Extreme deposit of dirt, ice and snow may reduce the value of function.
Don’t clean the sensors with vapour pressure cleaning machines.
12 month warranty for commercial use and 24 month warranty for private use only. The
location of buying (point of purchase) must be within the EU. The proof of warranty is the
original cashiers receipt with date and type of item on it. The owners manual and installation
instructions must be observed. No warranty of destruction by wrong installation, wrong
operation, non regulated use, using of unsuitable accessories, electrical shocks, fire,
moisture or smoke, damage by improper service and cleaning. Warranty repairs are free of
charge. No refund of shipping costs or labour as well as subsequent damages. Complaints
and repairs do not extend the warranty period.
Environmental Reference
Old electronic devices don’t belong into the bin.
If you want to dispose this equipment later, remove all
cables and send it back to Ampire.
You can dispose this device together with your old car, too.
You don’t have to remove it in this case.
The packing can be recycled. Dispose the packing in a
collecting system planned for it.
Electronics Subject to correction and technical modifications
ampire
2016
EN
The sensors should be installed 50-70cm over the
ground into the rear bumper.
The distance between the outside sensors should
be 126cm max.
To avoid wrong alarm or affecting the detecting
result, ensure no vehicle parts included in the
detection range at lateral angle of 90°.
The sensors must be fixed vertically, fixing up or
down may affect its performance.
The cable of sensors must point toward the
bottom.
To avoid collision or damage to sensors, the
sensor should be inserted completely into the
bumper and flush with the surface.
Stick the sick paper on the bumper then drill 4
holes in the selected position as the below.
To painting the sensors please stick the protective
ring onto the rubber ring of the sensors. Spray
paint on the sensor to achieve your desired colour
surface. Wait until the paint is dried off completely,
then detach the painting ring from the sensors and
throw it away.
Insert the ultrasonic detectors in the right order
(see 3. Installation Diagram) into the holes
separately and then fix them in right position.
Press the sensor with a slab, but not with fingers
directly to the avoid damaging the sensors.
The buzzer should be placed where the driver can hear the sound clearly.
Installation of Buzzer
Electronics Subject to correction and technical modifications
ampire
2016
EN
4
Installation Diagram
5
DIP-Switch
Red: Connect the red cable to 12V
ignition of the vehicle.
Black: Connect the black cable to chassis
ground.
Blue: Connect the blue cable to 12V of
the reversing light of the vehicle.
Red Socket: Connect the buzzer’s plug into the
red socket.
White Socket: Connect the sensor’s plug into the
white sockets.
Be sure of right order 1-4.
Detection Range and Indication
Electronics Subject to correction and technical modifications
ampire
2016
EN
Switch 1: 30 sec. turn off delay – On (up) / Off (down)
Switch 2: Display mode – On (up) / Off (down). The buzzer sounds only at stage 3 and 4 but the
optional display will show all stages. The buzzer stops sound at stage 4 after 5 sec. if the
vehicle don’t move anymore.
Switch 3: Turn on confirmation – Off (up) / On (down)
Switch 4: Display mirror mode – On (up) / Off (down)
Switch 5: Buzzer tone – Low (up) / High (down)
Reverse the vehicle slowly. The first rhythm of slow Bi---Bi--- sound indicates that the vehicle is 1,4m
away from the nearest obstacle. Still reverse the vehicle slowly. The sound will change as shown
under point 4. Stop the car immediatly when the buzzer gives a constant Bi sound as
this indicates the final distance of 0,3 m against the sensor.
Operational Test
Electronics Subject to correction and technical modifications
ampire
2016
EN
4
Installation Diagram
5
DIP-Switch
Red: Connect the red cable to 12V
ignition of the vehicle.
Black: Connect the black cable to chassis
ground.
Blue: Connect the blue cable to 12V of
the reversing light of the vehicle.
Red Socket: Connect the buzzer’s plug into the
red socket.
White Socket: Connect the sensor’s plug into the
white sockets.
Be sure of right order 1-4.
Detection Range and Indication
Electronics Subject to correction and technical modifications
ampire
2016
EN
Switch 1: 30 sec. turn off delay – On (up) / Off (down)
Switch 2: Display mode – On (up) / Off (down). The buzzer sounds only at stage 3 and 4 but the
optional display will show all stages. The buzzer stops sound at stage 4 after 5 sec. if the
vehicle don’t move anymore.
Switch 3: Turn on confirmation – Off (up) / On (down)
Switch 4: Display mirror mode – On (up) / Off (down)
Switch 5: Buzzer tone – Low (up) / High (down)
Reverse the vehicle slowly. The first rhythm of slow Bi---Bi--- sound indicates that the vehicle is 1,4m
away from the nearest obstacle. Still reverse the vehicle slowly. The sound will change as shown
under point 4. Stop the car immediatly when the buzzer gives a constant Bi sound as
this indicates the final distance of 0,3 m against the sensor.
Operational Test
Electronics Subject to correction and technical modifications
ampire
2016
EN
ampire
Langwadener Straße 60
D-41516 Grevenbroich
Support
+49 2181-81955-0
www.ampire.de
© 2016 AMPIRE ELECTRONICS. All rights reserved. Reproduction in whole or in part without written permission.
PSA400C
Since its founding in 1987 Ampire Electronics has only one goal, to provide the best possible
Autoalarm-, Autohifi- and Multimedia products, which are available on the international market.
All manufacturing facilities and suppliers are certified according to ISO 9001 and QS-9000.
Ampire quality products are sold worldwide.
An Ampire customer service is available in many countries.
For more information about distributors in your territory please call: + 49-2181-81955-0.
We are focused on future oriented development of user friendly products.
The outstanding high quality standards, functionalities and designs of our products are
unique in the market. "German Development" is taken literally in AMPIRE.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Ampire PSA400C Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI