KYOCERA 1650 User manual

This Operation Guide is for 1650, 2050, and 2550. This Operation Guide mentions that 1650 is a

16 ppm (prints per minute) model, 2050 is a 20 ppm (prints per minute) model, and 2550 is a

25 ppm (prints per minute) model.

Note This Operation Guide contains information that corresponds to using both the inch and metric

versions of this machine.

This Operation Guide shows messages of the inch version. When using the metric version, see

the messages of the inch version for reference. With regard to the messages in the text, if a

message has only the difference of upper- and lower-case spelling, we show only the message

of the inch version. When there is even a slight difference in the message, we have listed the

information for the inch version followed, in brackets, by the corresponding information for the

metric version.

i

CONTENTS

1 Names of Parts ............................................................................................... 1-1

Main Body ................................................................................................................................1-1

Operation Panel .......................................................................................................................1-4

2 Preparations ................................................................................................... 2-1

Loading Paper ..........................................................................................................................2-1

Note for Adding Paper ........................................................................................................2-1

Loading Paper into the Cassette ........................................................................................2-2

Setting Paper in the Multi-Bypass Tray ..............................................................................2-4

Multi-Bypass Tray Settings .................................................................................................2-6

Connecting the Cables ...........................................................................................................2-11

Connecting the Network Cable .........................................................................................2-11

Connecting the Printer Cable ...........................................................................................2-11

Connecting the Power Cord ...................................................................................................2-13

Turning the Power On ............................................................................................................2-14

Network (TCP/IP) Settings .....................................................................................................2-15

Setting the Date and Time ......................................................................................................2-19

Language Setting ...................................................................................................................2-23

Other Settings ........................................................................................................................2-23

3 Basic Operation ............................................................................................. 3-1

Basic Copying Procedure .........................................................................................................3-1

Zoom Copying ..........................................................................................................................3-5

Auto Zoom Ratio Selection Mode .......................................................................................3-5

Zoom Mode ........................................................................................................................3-6

Preset Zoom Mode .............................................................................................................3-8

Duplex Copying ........................................................................................................................3-9

Split Copying ..........................................................................................................................3-12

Sort Copying ..........................................................................................................................3-15

Combine Copying ...................................................................................................................3-17

2 in 1 .................................................................................................................................3-18

4 in 1 (horizontal arrangement) ........................................................................................3-19

4 in 1 (vertical arrangement) .............................................................................................3-20

Interrupt Mode ........................................................................................................................3-21

Low Power Mode ...................................................................................................................3-23

Sleep Mode ............................................................................................................................3-24

Basic Printing Procedure ........................................................................................................3-25

Installing the Printer Driver ...............................................................................................3-25

Printing from Application Software ...................................................................................3-25

4 Optional Equipment ....................................................................................... 4-1

Document Processor ................................................................................................................4-1

Acceptable Originals ...........................................................................................................4-1

Notes on Use ......................................................................................................................4-2

Names of Parts ...................................................................................................................4-2

Setting Originals in the Document Processor .....................................................................4-2

Setting Originals on the Platen ...........................................................................................4-4

Paper Feeder ...........................................................................................................................4-5

Duplex Unit ...............................................................................................................................4-5

Finisher ....................................................................................................................................4-6

Names of Parts ...................................................................................................................4-6

Adding Staples ....................................................................................................................4-7

Clearing Staple Jam ...........................................................................................................4-8

Job Separator ...........................................................................................................................4-9

Key Counter ...........................................................................................................................4-10

Fax Kit ....................................................................................................................................4-10

ii

Network Scanner Kit .............................................................................................................. 4-10

Memory Card (CompactFlash) ...............................................................................................4-11

Hard Disk ................................................................................................................................4-11

Additional Memory ..................................................................................................................4-11

Optional Equipment ............................................................................................................... 4-12

5 Maintenance ................................................................................................... 5-1

Cleaning the Machine .............................................................................................................. 5-1

Replacing the Toner Container and the Waste Toner Box ....................................................... 5-5

6 Troubleshooting ............................................................................................. 6-1

If Trouble Occurs ..................................................................................................................... 6-1

Displayed Messages ............................................................................................................... 6-4

Paper Jams ............................................................................................................................. 6-8

Jam Location Indicators ..................................................................................................... 6-8

Notes ................................................................................................................................. 6-9

Removal Procedures ......................................................................................................... 6-9

Appendix ..................................................................................................... Appendix-1

Specifications ............................................................................................................. Appendix-1

Main Body ............................................................................................................. Appendix-1

Copier Functions ................................................................................................... Appendix-2

Printer Functions ................................................................................................... Appendix-3

Document Processor (optional) ............................................................................ Appendix-3

Paper Feeder (optional) ........................................................................................ Appendix-3

Duplex Unit (optional) ........................................................................................... Appendix-4

Finisher (optional) ................................................................................................. Appendix-4

Job Separator (optional) ....................................................................................... Appendix-4

Environmental Specifications ................................................................................ Appendix-5

Index ................................................................................................................... Index-1

iii

MAKING FULL USE OF THE ADVANCED FUNCTIONS OF THIS

MACHINE

1 Automatic selection of the copy

paper of the same size as the

original

(See page 3-2.)

2 Reduction/enlargement for a

specified cassette size <Auto

zoom ratio selection mode>

(See page 3-5.)

3 Reduction/enlargement in the

range from 25 to 200 %

<Zoom mode> (See page 3-6.)

4 One-touch selection of the copy

magnification ratio

(See page 3-8.)

5 Making 2-sided copies from

various types of originals

(See page 3-9.)

6 Copying two-page originals onto

separate sheets

(See page 3-12.)

7 Automatic sorting of copy sets

(See page 3-15.)

8 Change of orientation of copies

by set <Offset copying>

(Refer to Chapter 1 in

Advanced Operation Guide,

Offset Copying.)

9 Combination of two or four

originals onto a single copy

page <Combine copying>

(See page 3-17.)

8 1/2 × 11"

A4

11 × 17": 129 %

A3: 141 %

5 1/2 × 8 1/2": 64 %

A5: 70 %

25 %

200 %

2

1

21

2

1

2

3

2

1

3

2

1

3

2

1

3

2

1

2

1

2

iv

10 Making a margin space on

copies <Margin mode>

(Refer to Chapter 1 in

Advanced Operation Guide,

Margin Mode.)

11 Making copies with clean edges

(Refer to Chapter 1 in

Advanced Operation Guide,

Border Erase Mode.)

12 Copying a large volume of

originals in one operation

(Refer to Chapter 1 in

Advanced Operation Guide,

Continuous Copying.)

13 Memorizing copy settings

<Program function> (Refer to

Chapter 1 in Advanced

Operation Guide, Program

Function.)

14 Selection of the language used

in the message

(See page 2-23.)

15 Using ID-codes to control the

number of copies made

(Refer to Chapter 4 in

Advanced Operation Guide.)

16 Full range of optional equipment

Document processor

(See page 4-1.)

Paper feeder (See page 4-5.) Duplex unit (See page 4-5.)

Finisher (See page 4-6.) Job separator (See page 4-9.) Key counter (See page 4-10.)

English

v

Fax kit (See page 4-10.) Network scanner kit

(See page 4-10.)

Memory card (CompactFlash)

(See page 4-11.)

Hard Disk (See page 4-11.) Additional memory

(See page 4-11.)

vi

Notice The information in this guide is subject to change without notification. Additional pages may be

inserted in future editions. The user is asked to excuse any technical inaccuracies or

typographical errors in the present edition.

No responsibility is assumed if accidents occur while the user is following the instructions in this

guide. No responsibility is assumed for defects in the printer’s firmware (contents of its read-only

memory).

This guide, any copyrightable subject matter sold or provided with or in connection with the sale

of the machine, are protected by copyright. All rights are reserved. Copying or other

reproduction of all or part of this guide, any copyrightable subject matter without the prior written

consent of Kyocera Mita Corporation is prohibited. Any copies made of all or part of this guide,

any copyrightable subject must contain the same copyright notice as the material from which the

copying is done.

Regarding Tradenames

PRESCRIBE is a registered trademark of Kyocera Corporation. KPDL and KIR (Kyocera Image

Refinement) are trademarks of Kyocera Corporation.

Diablo 630 is a product of Xerox Corporation. IBM Proprinter X24E is a product of International

Business Machines Corporation. Epson LQ-850 is a product of Seiko Epson Corporation.

Hewlett-Packard, PCL, and PJL are registered trademarks of Hewlett-Packard Company.

Centronics is a trade name of Centronics Data Computer Corp. PostScript is a registered

trademark of Adobe Systems Incorporated. Macintosh is a registered trademark of Apple

computer, Inc. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft

Corporation. PowerPC is a trademark of International Business Machines Corporation.

ENERGY STAR is a U.S. registered mark. All other brand and product names are registered

trademarks or trademarks of their respective companies.

CompactFlash and CF are trademarks of SanDisk Corporation of America.

The Kyocera product uses PeerlessPrintXL to provide the HP LaserJet compatible PCL6

language emulation. PeerlessPrintXL is a trademark of The Peerless Group, Redondo Beach,

CA 90278, U.S.A.

This product contains UFST™ and MicroType

®

from Agfa Monotype Corporation.

Legal Restriction On Copying

• It may be prohibited to copy copyrighted material without permission of the copyright owner.

• It is prohibited under any circumstances to copy domestic or foreign currencies.

• Copying other items may be prohibited.

vii

Energy Star Program

We have determined as a participating company in the International Energy Star Program that

this product is compliant with the standards laid out in the International Energy Star Program.

International Energy Star Program has as its basic goals the promotion of efficient energy use

and the reduction of the environmental pollution that accompanies energy consumption by

promoting the manufacture and sale of products that fulfill program standards.

Low Power Mode

The device automatically enters Low Power Mode when 9 minutes have passed since the

device was last used. The amount of time of no activity that must pass before Low Power Mode

is activated may be lengthened. See Low Power Mode on page 3-23 for more information.

Sleep Mode

The device automatically enters Sleep Mode when 19 minutes have passed since the device

was last used. The amount of time of no activity that must pass before Sleep Mode is activated

may be lengthened. For more information see Sleep Mode on page 3-24.

Automatic 2-Sided Copy Function

The Energy Star Program encourages the use of 2-sided copying which reduces the load on the

environment. Your sales or service representative can provide information about adding 2-sided

copying capabilities to this device.

Paper Recycling

The Energy Star Program encourages the use of environmentally friendly recycled paper. Your

sales or service representative can provide information about recommended paper types.

About the International Energy Star Program

viii

Please read this Operation Guide before using this machine. Keep it close to the machine for easy reference.

Please read this Operation Guide before using this machine. Keep it close to the machine

for easy reference.

The sections of this guide and parts of the machine marked with symbols are safety warnings

meant to protect the user, other individuals and surrounding objects, and ensure correct and

safe usage of the machine. The symbols and their meanings are indicated below.

Symbols

The symbol indicates that the related section includes safety warnings. Specific points of

attention are indicated inside the symbol.

The symbol indicates that the related section includes information on prohibited actions.

Specifics of the prohibited action are indicated inside the symbol.

DANGER: Indicates that serious injury or even death will very possibly result

from insufficient attention to or incorrect compliance with the related points.

WARNING: Indicates that serious injury or even death may result from

insufficient attention to or incorrect compliance with the related points.

CAUTION: Indicates that personal injury or mechanical damage may result from

insufficient attention to or incorrect compliance with the related points.

.... [General warning]

.... [Warning of danger of electrical shock]

.... [Warning of high temperature]

.... [Warning of prohibited action]

.... [Disassembly prohibited]

ix

The z symbol indicates that the related section includes information on actions which must be

performed. Specifics of the required action are indicated inside the symbol.

Please contact your service representative to order a replacement if the safety warnings in this

Operation Guide are illegible or if the guide itself is missing. (fee required)

.... [Alert of required action]

.... [Remove the power plug from the outlet]

.... [Always connect the machine to an outlet with a ground connection]

x

IMPORTANT! PLEASE READ FIRST.

CAUTION LABELS

Caution labels have been attached to the machine at the following locations for safety purposes.

Be sufficiently careful to avoid fire or electric shock when removing a paper jam or when

replacing toner.

NOTE: Do not remove these labels.

Label 2

High temperature inside. Do not touch

parts in this area, because there is a

danger of getting burned.

Label 3

High voltage inside. Never touch parts

in this area, because there is a danger

of electric shock.

Label 1

High temperature inside. Do not touch parts in

this area, because there is a danger of getting

burned.

Label 4

High temperature inside. Do not touch

parts in this area, because there is a

danger of getting burned.

xi

INSTALLATION PRECAUTIONS

Environment

Caution

Avoid placing the machine on or in locations which are unstable or not level. Such

locations may cause the machine to fall down or fall over. This type of situation

presents a danger of personal injury or damage to the machine.

Avoid locations with humidity or dust and dirt. If dust or dirt become attached to the

power plug, clean the plug to avoid the danger of fire or electrical shock.

Avoid locations near radiators, heaters, or other heat sources, or locations near

flammable items, to avoid the danger of fire.

To keep the machine cool and facilitate changing of parts and maintenance, allow

access space as shown below. Leave adequate space, especially around the vents,

to allow air to be properly ventilated out of the machine.

Other precautions

Adverse environmental conditions may affect the safe operation and performance of the

machine. Install in an air-conditioned room (recommended room temperature: around 73.4 °F

(23 °C), humidity: around 50 %), and avoid the following locations when selecting a site for the

machine.

• Avoid locations near a window or with exposure to direct sunlight.

• Avoid locations with vibrations.

• Avoid locations with drastic temperature fluctuations.

• Avoid locations with direct exposure to hot or cold air.

• Avoid poorly ventilated locations.

Left:

11 13/16"

30 cm

Front:

39

3/8"

100 cm

Right:

11

13/16"

30 cm

Rear:

3 15/16"

10 cm

xii

If the floor is delicate, when this product is moved after installation, the floor material may be

damaged.

During copying, some ozone is released, but the amount does not cause any ill effect to one's

health. If, however, the machine is used over a long period of time in a poorly ventilated room or

when making an extremely large number of copies, the smell may become unpleasant. To

maintain the appropriate environment for copy work, it is suggested that the room be properly

ventilated.

Power supply/Grounding the machine

Warning

Do not use a power supply with a voltage other than that specified. Avoid multiple

connections in the same outlet. These types of situations present a danger of fire or

electrical shock.

Plug the power cord securely into the outlet. If metallic objects come in contact with

the prongs on the plug, it may cause a fire or electric shock.

Always connect the machine to an outlet with a ground connection to avoid the

danger of fire or electrical shock in case of an electric short. If an earth connection is

not possible, contact your service representative.

Other precautions

Connect the power plug to the closest outlet possible to the machine.

The power supply cord is used as the main disconnect device. Ensure that the socket/outlet is

located/installed near the equipment and is easily accessible.

Handling of plastic bags

Warning

Keep the plastic bags that are used with the machine away from children. The plastic

may cling to their nose and mouth causing suffocation.

PRECAUTIONS FOR USE

Cautions when using the machine

Warning

Do not place metallic objects or containers with water (flower vases, flower pots,

cups, etc.) on or near the machine. This situation presents a danger of fire or

electrical shock should they fall and spill liquids inside.

Do not remove any of the covers from the machine as there is a danger of electrical

shock from high voltage parts inside the machine.

xiii

Do not damage, break or attempt to repair the power cord. Do not place heavy

objects on the cord, pull it, bend it unnecessarily or cause any other type of damage.

These types of situations present a danger of fire or electrical shock.

Never attempt to repair or disassemble the machine or its parts as there is a danger

of fire, electrical shock or damage to the laser. If the laser beam escapes, there is a

danger of it causing blindness.

If the machine becomes excessively hot, smoke appears from the machine, there is

an odd smell, or any other abnormal situation occurs, there is a danger of fire or

electrical shock. Turn the main power switch off ({) immediately, be absolutely

certain to remove the power plug from the outlet and then contact your service

representative.

If anything harmful (paper clips, water, other fluids, etc.) falls into the machine, turn

the main power switch off ({) immediately. Next, be absolutely certain to remove the

power plug from the outlet to avoid the danger of fire or electrical shock. Then contact

your service representative.

Do not remove or connect the power plug with wet hands, as there is a danger of

electrical shock.

Always contact your service representative for maintenance or repair of internal parts.

Caution

Do not pull the power cord when removing it from the outlet. If the power cord is

pulled, the wires may become broken and there is a danger of fire or electrical shock.

(always grasp the power plug when removing the power cord from the outlet.)

Always remove the power plug from the outlet when moving the machine. If the

power cord is damaged, there is a danger of fire or electrical shock.

If the machine will not be used for a short period of time (overnight, etc.), turn the

main power switch off ({). If it will not be used for an extended period of time

(vacations, etc.), remove the power plug from the outlet for safety purposes during

the time the machine is not in use.

Always hold the designated parts only when lifting or moving the machine.

For safety purposes, always remove the power plug from the outlet when performing

cleaning operations.

If dust accumulates within the machine, there is a danger of fire or other trouble. It is

therefore recommended that you consult with your service representative in regard to

cleaning of internal parts. This is particularly effective if accomplished prior to

seasons of high humidity. Consult with your service representative in regard to the

cost of cleaning the internal parts of the machine.

Other precautions

Do not place heavy objects on the machine or cause other damage to the machine.

Do not open the upper front cover, turn off the main power switch, or pull out the power plug

during copying.

When lifting or moving the machine, contact your service representative.

xiv

Do not touch electrical parts, such as connectors or printed circuit boards. They could be

damaged by static electricity.

Do not attempt to perform any operations not explained in this handbook.

Caution: Use of controls or adjustments or performance of procedures other than those

specified herein may result in hazardous radiation exposure.

Do not look directly at the light from the scanning lamp as it may cause your eyes to feel tired or

painful.

Other precautions (for users in California, the United States)

This product contains a CR Coin Lithium Battery which contains Perchlorate Material - special

handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

.

Cautions when handling consumables

Caution

Do not attempt to incinerate the toner container or the waste toner box. Dangerous

sparks may cause burns.

Keep the toner container and the waste toner box out of the reach of children.

If toner happens to spill from the toner container or the waste toner box, avoid

inhalation and ingestion, as well as contact with your eyes and skin.

• If you do happen to inhale toner, move to a place with fresh air and gargle

thoroughly with a large amount of water. If coughing develops, contact a

physician.

• If you do happen to ingest toner, rinse your mouth out with water and drink 1 or 2 cups of

water to dilute the contents of your stomach. If necessary, contact a physician.

• If you do happen to get toner in your eyes, flush them thoroughly with water. If there is any

remaining tenderness, contact a physician.

• If toner does happen to get on your skin, wash with soap and water.

DO NOT attempt to force open or destroy the toner container or the waste toner box.

Other precautions

After use, ALWAYS dispose of the toner container and the waste toner box in

accordance with Federal, State and Local rules and regulations.

Store all consumables in a cool, dark location.

If you will not be using the copier for a prolonged period of time, remove all paper from the

cassette and the multi-bypass tray and seal in its original packaging.

xv

SAFETY OF LASER BEAM

1. Safety of laser beam

This copier has been certified by the manufacturer to Class 1 level under the radiation

performance standards established by the U.S.DHHS (Department of Health and Human

Services) in 1968. This indicates that the product is safe to use during normal operation and

maintenance. The laser optical system, enclosed in a protective housing and sealed within the

external covers, never permits the laser beam to escape.

2. The CDRH Act

A laser-product-related act was implemented on Aug. 2, 1976, by the Center for Devices and

Radiological Health (CDRH) of the U.S. Food and Drug Administration (FDA). This act prohibits

the sale of laser products in the U.S. without certification, and applies to laser products

manufactured after Aug. 1, 1976. The label shown below indicates compliance with the CDRH

regulations and must be attached to laser products marketed in the United States. On this

copier, the label is on the right.

3. Optical unit

When checking the optical unit, avoid direct exposure to the laser beam, which is invisible.

Shown at below is the label located on the cover of the optical unit.

4. Maintenance

For safety of the service personnel, follow the maintenance instructions in the other section of

this manual.

5. Safety switch

The power to the laser unit is cut off when the upper front cover is opened.

16 ppm model/20 ppm model 25 ppm model

xvi

Safety Instructions Regarding the Disconnection of Power

Caution The power plug is the main isolation device! Other switches on the equipment are only

functional switches and are not suitable for isolating the equipment from the power source.

Attention Le débranchement de la fiche secteur est le seul moyen de mettre l’appareil hors tension. Les

interrupteurs sur l’appareil ne sont que des interrupteurs de fonctionnement: ils ne mettent pas

l’appareil hors tension.

WARNING

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION — The changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

* The above warning is valid only in the United States of America.

xvii

1650/2050/2550 MULTIFUNCTIONAL PRODUCT LIMITED

WARRANTY

1. Kyocera Mita America, Inc. and Kyocera Mita Canada, Ltd. (both referred to as "Kyocera")

warrants the Customer's new Multifunctional Product (referred to as "MFP"), and the new

accessories installed with the initial installation of the MFP, against any defects in material and

workmanship for a period of one (1) year, or 150,000 copies/prints from date of installation by an

Authorized Kyocera Dealer for the 1650/2050, or 300,000 copies/prints from date of installation

by an Authorized Kyocera Dealer for the 2550, whichever first occurs. In the event the MFP or

an accessory is found to be defective within the warranty period, Kyocera's only obligation and

the Customer's exclusive remedy shall be replacement of any defective parts. It is understood

that Kyocera shall have no obligation to furnish labor.

2. This warranty is valid only as to the original retail purchaser (referred to as the "Customer") of a

new Kyocera MFP in the United States of America or Canada, based upon the country of

purchase.

3. In order to obtain performance of this warranty, the Customer must immediately notify the

Authorized Kyocera Dealer from whom the product was purchased. If the Kyocera Dealer is not

able to provide service, write to Kyocera at the address below for the name and address of the

Authorized Kyocera Dealer in your area or check our Website at www.kyoceramita.com/us.

4. This warranty does not cover MFP's or accessories: (a) which have become damaged due to

operator negligence, misuse, accidents, improper storage or unusual physical or electrical

stress, (b) which have used parts or supplies which are not genuine Kyocera brand parts or

supplies, (c) which have been serviced by a technician not employed by Kyocera or an

Authorized Kyocera Dealer, or (d) which have had the serial number modified, altered, or

removed.

5. This warranty does not cover Maintenance Kits or the components of Maintenance Kits, which

consist of the drum unit, the fixing unit, and the developing unit. Kyocera shall give the Customer

a separate warranty for these items.

6. This warranty gives the Customer specific legal rights. The Customer may also have other

rights, which vary from state to state, or province to province. Neither the seller, nor any other

person is authorized to extend the time period, or expand this warranty on behalf of Kyocera.

7. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES AND (CONDITIONS),

EXPRESS OR IMPLIED, AND KYOCERA SPECIFICALLY DISCLAIMS ANY IMPLIED

WARRANTY (OR CONDITION) OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE. THIS WARRANTY SHALL NOT EXTEND TO, AND KYOCERA SHALL NOT BE

LIABLE FOR, ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES WHICH MAY ARISE OUT

OF THE USE, OR INABILITY TO USE, THE MFP.

xviii

Guide to this Operation Guide

This operation guide has the following chapters. The content of these chapters is summarized

below to be used as a reference.

1Names of Parts

This chapter contains explanations on the names and functions of the parts of the machine and

its operation panel.

2 Preparations

This chapter contains explanations on procedures for loading paper and connection of this

product.

3 Basic Operation

This chapter contains explanations on the basic procedures of simple copying and printing.

4 Optional Equipment

This chapter contains explanations on the optional equipment that can be used with this product.

5 Maintenance

This chapter contains explanations on replacement of the toner container and the waste toner

box and maintenance of this product.

6 Troubleshooting

This chapter contains explanations on handling problems that may occur, for example, when an

error message appears or if a paper jam occurs.

Appendix

The appendix explains the specifications of this product.

Page is loading ...

KYOCERA 1650 User manual

KYOCERA 1650 User manual

Related papers

Other documents