IMG STAGELINE TXS-875DS User manual

Brand: IMG STAGELINE

Model: TXS-875DS

Type: User manual

Page is loading ...

12V /1A

1CASCADE CASCADE2 23 34 4

ANT. A O UTPUT ANT. B O UTPUT

OUTPUT

12V /1A

OUTPUT

ANT. A ANT. B

230 V~

50 Hz

FUSE

12V /1A

1 12 23 34 4

ANT. A O UTPUT ANT. B O UTPUT

OUTPUT

12V /1A

OUTPUT

230 V~

50 Hz

FUSE

Antenna splitter TXS-875DS

AF OUT.

UNBAL .

AF OUT.

BAL .

12 V

Receiver 4

ANT. 2

ANT. 1

12 V

AF OUT.

UNBAL .

AF OUT.

BAL .

12 V

Receiver 3

ANT. 2

ANT. 1

12 V

AF OUT.

UNBAL .

AF OUT.

BAL .

12 V

Receiver 2

ANT. 2

ANT. 1

12 V

AF OUT.

UNBAL .

AF OUT.

BAL .

12 V

Receiver 1

ANT. 2

ANT. 1

12 V

antenna splitter TXS-875DS

ANT. A

Signal

ANT. B

Signal

ANT. A

OUT 2

ANT. A

OUT 1

ANT. B

OUT 4

ANT. B

OUT 3

ANT. B

OUT 2

ANT. B

OUT 1

ANT. A

OUT 3

ANT. A

OUT 4

ANT. A IN ANT. B IN

ANT. A ANT. B

CASCADE CASCADE

Receivers 5 … 8

ANT. A

OUT 2

ANT. A

OUT 1

ANT. B

OUT 4

ANT. B

OUT 3

ANT. B

OUT 2

ANT. B

OUT 1

ANT. A

OUT 3

ANT. A

OUT 4

Power supply

DC 12

Power supply

DC 12

Power supply

DC 12

Power supply

DC 12

➀

DE Montage der

BNC-Doppelbuchsen

GB Installation of the BNC

jack-to-jack adapters

FR Montage des adaptateurs

BNC femelle / femelle

IT Montaggio delle prese BNC

doppie

NL Montage van de dubbele BNC-

jacks

ES Instalación de los adaptadores

BNC toma / toma

PL Montaż gniazd przelotowych

BNC

➁

DE Schalter für die Versorgungsspannung der

Antennensignal-Verstärker TXS-875B

GB Switch for the supply voltage of the

antenna signal ampliﬁers TXS-875B

FR Interrupteur pour la tension d‘alimentation des

ampliﬁcateurs de signal d'antenne TXS-875B

Interruttore per la tensione d’alimentazione degli

ampliﬁcatori dei segnali di antenne TXS-875B

NL Schakelaar voor de voedingsspanning van de

antennesignaalversterkers TXS-875B

ES Interruptor para el voltaje de alimentación de

los amplﬁcadores de señal de antena TXS-875B

PL Włącznik zasilania dla wzmacniaczy anteno-

wych TXS-875B

ANT. B CASCADE 1.

OFF−ON

OUTPUT

➂

DE Anschlussmöglichkeiten

GB Connection options

FR Possibilités de branchement

IT Possibilità di collegamento

NL Aansluitmogelijkheden

ES Opciones de conexión

PL Opcje podłączania

Page is loading ...

Italiano

Italiano Pagina

Español

Español Página

English

4 45 6 8 9 78 6

12V /1 A

1 1CASCADE CASCADE2 23 34 4

ANT. A OUTPUT ANT. B OUTPUT

OUTPUT

12V /1 A

OUTPUT

ANT. A ANT. B

230 V~

50 Hz

FUSE

4-Way Antenna Splitter

These instructions are intended for users without

any speciﬁc technical knowledge. Please read the

instructions carefully prior to operation and keep

them for later reference. Figures 1– 3 can be found

on page 2.

1 Overview

BNC jacks, to install the reception antennas on

the front panel;

for insertion of the jacks refer to ﬁg.1

2 Power LED

3 POWER switch

Rear side of the BNC jacks (1); connect the jacks

to the antenna inputs ANT. A and ANT. B (7)

5 Mains jack for connection to a socket (230 V/

50 Hz) via the mains cable provided

The fuse holder is underneath this jack; always

replace a blown fuse by one of the same type!

Power supply jacks DC OUTPUT for four re-

ceivers

7 BNC input jacks ANT. A and ANT. B for the an-

tenna signals

BNC output jacks ANT. A CASCADE and ANT. B

CASCADE to route the antenna signals to an-

other antenna splitter TXS-875DS

BNC output jacks ANT. A 1 … 4 and ANT. B 1 … 4

to distribute the antenna signals to the antenna

inputs of four receivers

2 Safety Notes

This unit corresponds to all relevant directives of

the EU and is therefore marked with .

WARNING

The unit uses dangerous mains

voltage. Never make any modiﬁ-

cation on the unit not described in

these instructions; inexpert han-

dling may result in electric shock.

•

The unit is suitable for indoor use only. Pro-

tect it against dripping water, splash water

and high air humidity. The admissible am-

bient temperature range is 0 – 40 °C.

•

Do not place any vessels ﬁlled with liquid, e. g.

drinking glasses, on the unit.

•

Immediately disconnect the mains plug from

the socket

1. if the unit or the mains cable is visibly dam-

aged,

if a defect might have occurred after the unit

was dropped or suffered a similar accident,

3. if malfunctions occur.

In any case the unit must be repaired by skilled

personnel.

•

Never pull the mains cable to disconnect the

mains plug from the socket, always seize the

plug.

•

For cleaning only use a dry, soft cloth; never

use water or chemicals.

•

No guarantee claims for the unit and no liability

for any resulting personal damage or material

damage will be accepted if the unit is used for

other purposes than originally intended, if it is

not correctly connected or operated, or if it is

not repaired in an expert way.

If the unit is to be put out of operation

deﬁnitively, take it to a local recycling

plant for a disposal which is not harmful

to the environment.

3 Applications

The antenna splitter TXS-875DS is designed for

operating up to four multifrequency receivers from

IMG STAGELINE which

– operate in a frequency range between 470 and

960 MHz

– are equipped with removable antennas (BNC

connection)

– are supplied with +12 V/1 A max.

The TXS-875DS makes it easier to set up the audio

transmission system: Only two of the antennas

supplied with each receiver (one pair for each re-

ceiver) are required for connection to the antenna

splitter; all other antennas and the power supply

units of the receivers are not required. The split-

ter will send the antenna signals to the receivers

and supply the receivers with power. Matching

connection cables are supplied.

When more than four receivers are operated,

the cascade outputs (8) can be used to connect

multiple TXS-875DS in series. Each antenna split-

ter will be able to supply four receivers with power.

The antenna splitter can also be used in connec-

tion with the antenna signal ampliﬁers TXS-875B

(available as a pair). The antenna splitter will sup-

ply the ampliﬁers with power.

4 Operation

4.1 Preparation and setting up

1) When the antenna signal ampliﬁers TXS-875B

are used, the 12 V supply voltage for these

ampliﬁers must be available at the jacks ANT. A

and ANT. B (7). Prior to operation, please make

sure that the corresponding switch for the sup-

ply voltage in the unit (ﬁg. 2 on page 2) has

been set to the position ON.

WARNING

Always disconnect the mains

plug before opening the unit;

otherwise, you will risk an

electric shock.

2) To install the reception antennas on the front

panel of the TXS-875DS, insert the two BNC

jack-to-jack adapters supplied with the unit into

the mounting holes on the left and on the right

and screw them on (refer to ﬁg. 1 on page 2).

Place the antenna splitter on a ﬂat surface

or install it into a rack for units with a width

of 482 mm (19”). For installation into a rack,

1rack space (= 44.45 mm) is required.

4.2 Connection and switching on

The connection options can be found in ﬁg.3

on page 2.

1) Connect the low voltage jacks DC OUTPUT (6)

to the power supply jacks of the receivers.

Connect the antenna pair of one of the receiv-

ers to the antenna splitter:

– either to the two jacks (1) on the front panel

of the unit; in this case, connect the rear

side (4) of these jacks to the jacks ANT. A

and ANT. B (7)

– or directly to the two jacks ANT. A and ANT. B

(7) on the rear panel of the unit.

When using the antenna signal ampliﬁers

TXS-875B, insert the ampliﬁers between the

antennas and the antenna splitter.

Connect the two antenna inputs of each re-

ceiver to an antenna output ANT. A 1 … 4 and

to the corresponding antenna output ANT. B

1 … 4 (9).

4) The antenna signals can be routed to an other

TXS-875DS: Connect the outputs ANT. A

CASCADE and ANT. B CASCADE (8) to the

inputs ANT. A and ANT. B (7) of the following

TXS-875DS. This splitter in turn allows con-

nection of four receivers.

Finally, connect the mains cable provided to the

mains jack (5) and connect the mains plug of

the cable to a socket (230 V/ 50 Hz).

6) To switch the antenna splitter on or off, press

the button POWER (3). When the unit is

switched on, the power LED (2) will light up.

Notes:

1. If the antenna splitter provides 4 receivers with

power, the switch-on current of all receivers may

be too high and the power supply unit of the splitter

will not start. In this case, brieﬂy switch off one of

the receivers.

2. If the

TXS-875DS

is not used for a longer period

of time, always disconnect the mains plug from

the mains socket; even when the splitter has been

switched off, it will still consume some power while

it is connected to the mains.

5 Speciﬁcations

Frequency range: . . . . . . . 470 – 960 MHz

RF ampliﬁcation: . . . . . . . . 3 dB

DC voltage outputs: . . . . . 12 V, 1 A (4 ×)

Ambient temperature:

. . . 0 – 40 °C

Power supply: . . . . . . . . . . 230 V/ 50 Hz

Power consumption: . . . . . 60 VA

Connections for

antenna signals:

. . . . . . . . BNC jacks, 50 Ω

Operating voltage (DC) for

antenna signal ampliﬁers:

. 12 V (can be

switched off)

Dimensions:

. . . . . . . . . . . 482 × 45 × 250 mm,

1 rack space

Weight: . . . . . . . . . . . . . . 2.2 kg

Subject to technical modiﬁcation.

INTERNATIONAL GmbH

& Co. KG. No part of this instruction manual may be repro-

duced in any form or by any means for any commercial use.

English

English Page

Page is loading ...

MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany

A-1777.99.01.07.2016

IMG STAGELINE TXS-875DS User manual

Brand: IMG STAGELINE

Model: TXS-875DS

Type: User manual

Download PDF

report

in other languages

italiano: IMG STAGELINE TXS-875DS Manuale utente
français: IMG STAGELINE TXS-875DS Manuel utilisateur
español: IMG STAGELINE TXS-875DS Manual de usuario
Deutsch: IMG STAGELINE TXS-875DS Benutzerhandbuch
Nederlands: IMG STAGELINE TXS-875DS Handleiding
polski: IMG STAGELINE TXS-875DS Instrukcja obsługi

IMG STAGELINE TXS-875DS User manual

IMG STAGELINE TXS-875DS User manual

in other languages

Related papers

Other documents