LG LG W2294T-PF User manual

Brand: LG

Model: LG W2294T-PF

Category: TVs & monitors

Type: User manual

This manual is also suitable for

W2294T-PF

Make sure to read the Important Precautions before using the product.

Keep the User's Guide(CD) in an accessible place for future reference.

See the label attached on the product and give the information to your

dealer when you ask for service.

W2294T

User’s Guide

This unit has been engineered and manufactured to ensure your personal safety,

however improper use may result in potential electrical shock or fire hazards. In

order to allow the proper operation of all safeguards incorporated in this display,

observe the following basic rules for its installation, use, and servicing.

On Safety

Use only the power cord supplied with the unit. In case you use another power

cord, make sure that it is certified by the applicable national standards if not being

provided by the supplier. If the power cable is faulty in any way, please contact the

manufacturer or the nearest authorized repair service provider for a replacement.

The power supply cord is used as the main disconnection device. Ensure that the

socket-outlet is easily accessible after installation.

Operate the display only from a power source indicated in the specifications of

this manual or listed on the display. If you are not sure what type of power supply

you have in your home, consult with your dealer.

Overloaded AC outlets and extension cords are dangerous. So are frayed power

cords and broken plugs. They may result in a shock or fire hazard. Call your service

technician for replacement.

Do not Open the Display:

There are no user serviceable components inside.

There are Dangerous High Voltages inside, even when the power is OFF.

Contact your dealer if the display is not operating properly.

To Avoid Personal Injury :

Do not place the display on a sloping shelf unless properly secured.

Use only a stand recommended by the manufacturer.

Do not drop an object on or apply impact to the product. Do not throw any toys

or objects on the product screen.

It can cause injury to human, problem to product and damage the display.

To Prevent Fire or Hazards:

Always turn the display OFF if you leave the room for more than a short period

of time. Never leave the display ON when leaving the house.

Keep children from dropping or pushing objects into the display's cabinet

openings. Some internal parts carry hazardous voltages.

Do not add accessories that have not been designed for this display.

When the display is to be left unattended for an extended period of time, unplug

it from the wall outlet.

In the presence of thunder and lightning, never touch the power cord and signal

cable because it can be very dangerous. It can cause electric shock.

On Installation

Do not allow anything to rest upon or roll over the power cord, and do not place

the display where the power cord is subject to damage.

Important Precautions

Do not use this display near water such as near a bathtub, washbowl, kitchen

sink, laundry tub, in a wet basement, or near a swimming pool.

Displays are provided with ventilation openings in the cabinet to allow the release

of heat generated during operation. If these openings are blocked, built-up heat

can cause failures which may result in a fire hazard. Therefore, NEVER:

Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.

Place the display in a built-in enclosure unless proper ventilation is provided.

Cover the openings with cloth or other material.

Place the display near or over a radiator or heat source.

Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,

mar, or damage the Active Matrix LCD permanently.

Do not press the LCD screen with your finger for a long time as this may cause

some afterimages.

Some dot defects may appear as Red, Green or Blue spots on the screen.

However, this will have no impact or effect on the display performance.

If possible, use the recommended resolution to obtain the best image quality for

your LCD display. If used under any mode except the recommended resolution,

some scaled or processed images may appear on the screen. However, this is

characteristic of the fixed-resolution LCD panel.

Leaving a fixed image on the screen for a long time may cause damage to the

screen and cause image burn-in. Make sure to use a screen saver on the product.

Burn-in and related problems are not covered by the warranty on this product.

Do not shock or scratch the front and sides of the screen with metallic objects.

Otherwise, it may cause damage to the screen.

On Cleaning

Unplug the display before cleaning the face of the display screen.

Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display

screen because over-spraying may cause electrical shock.

On Repacking

Do not throw away the carton and packing materials. They make an ideal

container in which to transport the unit. When shipping the unit to another

location, repack it in its original material.

On Disposal

The fluorescent lamp used in this product contains a small amount of mercury.

Do not dispose of this product with general household waste.

Disposal of this product must be carried out in accordance to the regulations of

your local authority.

Connecting the Display

Before setting up the monitor, ensure that the power to the monitor, the computer

system, and other attached devices is turned off.

Connecting the stand

1. Place the monitor face down on the cushion or soft cloth.

3. Attach the monitor to the stand base by turning the screw to the right.

4. Once assembled take the monitor up carefully and face the front side.

2. Assemble the stand base into the standbody in the correct direction as shown in the picture.

Stand Base

Stand Body

Screw : Turn the

screw by using the

screw handle.

Connecting the Display

IMPORTANT

This illustration depicts the general model of connection. Your monitor may differ from the items

shown in the picture.

Do not carry the product upside down holding only the stand base. The product may fall and get

damaged or injure your foot.

5. Turn the screw to the left to separate the stand body

from the stand base.

-5

Before setting up the monitor, ensure that the power to the monitor, the computer

system, and other attached devices is turned off.

Positioning your display

1. Adjust the position of the panel in various ways for maximum comfort.

Tilt Range : -5˚~15˚

IMPORTANT

It is recommended that in order to maintain an ergonomic and comfortable

viewing position, the forward tilt angle of the monitor should not exceed 5

degrees.

When adjusting the angle of the screen, do not put your finger(s) in between

the head of the monitor and the stand body. You can hurt your finger(s).

Connecting the Display

Wall-outlet type

Mac adapter

For Apple Macintosh use, a separate plug adapter is needed

to change the 15 pin high density (3 row) D-sub VGA

connector on the supplied cable to a 15 pin 2 row connector.

DVI (This feature is not available in all countries.)

4. Touch the power button in front to turn on the monitor.

The 'Self Image Setting Function' will automatically run

when the monitor is on. (Only Analog Mode)

NOTE

‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user connects the

monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals.

‘AUTO/SET’ Function? When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen

while using the device or after changing screen resolution, press the AUTO/SET function button to improve resolution.

NOTE

This is a simplified representation of the rear view.

This rear view represents a general model; your display may differ from the view as shown.

User must use shielded signal interface cables (D-sub 15 pin cable, DVI cable) with ferrite cores to maintain

standard compliance for the product.

Connecting with the PC

1. Before setting up the monitor, ensure that the power to the monitor, the computer

system, and other attached devices is turned off.

2. Connect the signal cable . When attached, tighten the thumbscrews to secure the

connection.

3. Connect the power cable with the AC-DC adapter (AC-DC power supply) , and

then plug the cable in the outlet.

[ Arranging the cables]

[ Connecting the cables]

Power Button

Connecting the Display

To attach or separate the back door

1. To attach the back door, match the two holes and push the back door as shown in the image.

back door

NOTE

- Cover the back cap after connecting the cables before use.

(To connect the cable, see page 5 for reference.)

2. To separate the back door, hold the bottom part and pull it out.

Kensington Security Slot

Connected to a locking

cable that can be purchased

separately at most computer stores

Control Panel Functions

Front Panel Controls

Use this button to enter EZ ZOOMING, 4:3 IN WIDE,

PHOTO EFFECT items.

For more information, refer to page 11.

MENU Button

Use this button to enter or exit from the On Screen Display.

OSD LOCKED/UNLOCKED

This function allows you to lock the current control settings, so

that these settings are not inadvertently changed. To lock the

OSD settings, press and hold the MENU button for several

seconds. The message "OSD LOCKED" appears.

You can unlock the OSD settings at any time by pushing

the MENU button for several seconds. The message

"OSD UNLOCKED" appears.

Button

Side

Control Panel Functions

Use this button to turn the display on or off.

The power indicator stays blue if the display is running

properly (On mode). If the display is in power saving

mode, the power indicator is flickering blue.

Power Button/

Power Indicator

Use this button to enter a selection in the On Screen

Display.

AUTO/SET

Button

AUTO IMAGE ADJUSTMENT

When adjusting your display settings, always press

the AUTO/SET button before entering the On Screen

Display(OSD). This will automatically adjust your

display image to the ideal settings for the current

screen resolution size (display mode).

The best display mode is

1680 x 1050

Buttons

Use these buttons to select or adjust functions in the On

Screen Display.

For more information,

refer to page 16.

Use this button to make either D-Sub or DVI connector

active. This feature is used when two computers are

connected to the display. The default setting is D-Sub.

(SOURCE Hot key)

On Screen Display (OSD) Control Adjustment

Screen Adjustment

Making adjustments to the image size, position and operating parameters of

the display is quick and easy with the On Screen Display Control system.

A short example is given below to familiarize you with the use of the controls.

The following section is an outline of the available adjustments and selections

you can make using the OSD.

To make adjustments in the On Screen Display, follow these steps:

Press the MENU Button, then the main menu of the OSD appears.

To access a control, use the or Buttons. When the icon you want

becomes highlighted, press the AUTO/SET Button.

Use the / Buttons to adjust the image to the desired level. Use the

AUTO/SET Button to select other sub-menu items.

Press the MENU Buttononce to return to the main menu to select another

function. Press the MENU Buttontwice to exit from the OSD.

NOTE

Allow the display to stabilize for at least 30 minutes before making image adjustments.

- + - +

NOTE

The order of icons may differ depending on the model (10~16).

OSD (On Screen Display) menu languages on the monitor may differ from the manual.

On Screen Display(OSD) Selection and Adjustment

The following table indicates all the On Screen Display control, adjustment, and

setting menus.

Main menu Sub-menu A D Reference

EZ ZOOMING

4:3 IN WIDE

PHOTO

EFFECT

PICTURE

COLOR

TRACKING

SETUP

FLATRON

F-ENGINE

NORMAL

GAUSSIAN BLUR

SEPIA

MONOCHROME

BRIGHTNESS

CONTRAST

GAMMA

PRESET

sRGB

6500K

9300K

RED

GREEN

BLUE

HORIZONTAL

VERTICAL

CLOCK

PHASE

SHARPNESS

LANGUAGE

WHITE BALANCE

RTC

POWER INDICATOR

FACTORY RESET

OSD

POSITION

HORIZONTAL

VERTICAL

MOVIE

INTERNET

USER

NORMAL

DEMO

To adjust the resolution

To adjust the image size

To adjust the screen color mode

To adjust the brightness, contrast

and gamma of the screen

To customize the color of the screen

To adjust the position of the screen

To customize the screen status for

a user's operating environment

To select or customize desired

image settings

: Adjustable A : Analog Input D : Digital Input

To improve the clarity and stability

of the screen

Pressing the button on the right side of the monitor will display the OSD screen.

Main menu Description

EZ ZOOMING

To select the display resolution.

When you select 'EZ ZOOMING' in OSD, display

resolution goes one step down so characters and

images look bigger. When you select EZ

ZOOMING once again, it goes back to the

original resolution.

* This function is operated only if the 'forteManag-

er' is installed to PC.

MENU : Exit

, : Move

SET : Select

4:3 IN WIDE

To select the image size of the screen.

• WIDE : Switch to full screen mode according to

input image signal.

• 4 : 3 : Change the image signal ratio into 4:3.

WIDE

4:3

PHOTO

EFFECT

To select the color of the screen.

• NORMAL

The PhotoEffect function is disabled.

• GAUSSIAN BLUR

This option is to add the effect to the screen that

the dark and sharp image becomes brighter

and more blurred.

• SEPIA

This option changes the screen to be Sepia

tone. The Sepia tone is brown color tone.

• MONOCHROME

This option changed the screen to be Gray

tone. The screen image is displayed with just

white, black, gray colors.

Use the AUTO/SET button

to go to sub-menu.

MONOCHROME

NORMAL

GAUSSIAN BLUR

SEPIA

On Screen Display(OSD) Selection and Adjustment

You were introduced to the procedure of selecting and adjusting an item

using the OSD system. Listed below are the icons, icon names, and icon

descriptions of the all items shown on the Menu.

Press the MENU Button, then the main menu of the OSD appears.

Sub-menus

Menu Name

Icons

Main Menu

Button Tip

MENU : Exit

: Adjust (Decrease/Increase)

SET : Enter

: Select another sub-menu

: Restart to select sub-menu

On Screen Display(OSD) Selection and Adjustment

Main menu Sub menu Description

PICTURE

MENU : Exit

: Decrease

: Increase

SET : Select another sub-menu

BRIGHTNESS

CONTRAST

GAMMA

To adjust the brightness of the screen.

To adjust the contrast of the screen.

Set your own gamma value. : -50 / 0 / 50

On the monitor, high gamma values

display whitish images and low gamma

values display high contrast images.

PRESET

RED

GREEN

BLUE

Select the screen color.

• sRGB: Set the screen color to fit the

sRGB standard color

specification.

• 6500K: Slightly reddish white.

• 9300K: Slightly bluish white.

Set your own red color levels.

Set your own green color levels.

Set your own blue color levels.

COLOR

MENU : Exit

: Decrease

: Increase

SET : Select another sub-menu

On Screen Display(OSD) Selection and Adjustment

TRACKING

Main menu Sub menu Description

CLOCK

PHASE

SHARPNESS

To minimize any vertical bars or stripes

visible on the screen background.

The horizontal screen size will also

change.

To adjust the focus of the display.

This item allows you to remove any

horizontal noise and clear or sharpen

the image of characters.

To adjust the clearness of the screen.

HORIZONTAL

VERTICAL

To move image left and right.

To move image up and down.

MENU : Exit

: Decrease

: Increase

SET : Select another sub-menu

On Screen Display(OSD) Selection and Adjustment

Press the , buttons to reset immediately.

SETUP

MENU : Exit

: Adjust

SET : Select another

sub-menu

Main menu Sub menu Description

WHITE BALANCE NO

R T C ON

POWER INDICATOR ON

FACTORY RESET NO

To choose the language in which the

control names are displayed.

To adjust position of the OSD window on

the screen.

LANGUAGE

OSD

POSITION

WHITE

BALANCE

If the output of the video card is different

the required specifications, the color level

may deteriorate due to video signal

distortion. Using this function, the signal

level is adjusted to fit into the standard

output level of the video card in order to

provide the optimal image.

Activate this function when white and

black colors are present in the screen.

Restore all factory default settings

except "LANGUAGE."

FACTORY

RESET

POWER

INDICATOR

Use this function to set the power

indicator on the front side of the monitor

to ON or OFF.

If you set OFF, it will go off.

If you set ON at any time, the power

indicator will automatically be turned on.

R T C

If you set ON, you enable the Response

Time Control function and reduce the

afterimage of the screen.

If you set OFF, you disenable the

Response Time Control function and

operate at panel response time.

NOTE

If this does not improve the screen image, restore the factory default settings. If necessary, perform the

white balance function again. This function will be enabled only when the input signal is an analog signal.

On Screen Display(OSD) Selection and Adjustment

Icons

Menu Name

Sub-menu Name

Main menu Sub menu Description

MOVIE

INTERN

NORMAL

DEMO

USER

When you execute F-ENGINE, two tones will appear

on the screen as shown. The applied screen will

appear on the left side, whereas the non-applied

screen will appear on the right side. Press the SET

button to use the adjusted screen.

FLATRON F-ENGINE

Screen when applied Screen when not applied

Pressing the button on the right side of the monitor will display the OSD screen.

Select 'YES' in sub-menu to save adjustments.

This is under normal operating conditions.

* Normal mode is when f-ENGINE is turned off.

This feature lets you easily select the best desired

image condition optimized to the environment

(ambient illumination, image types etc).

MOVIE

: For animation images in videos or movies

INTERNET

: For text images (Word processing etc.)

USER

You can manually adjust brightness, ACE or RCM.

You can save or restore the adjusted value even

when using a different environment.

Not applied

Green enhance

: Exit

, : Move

SET : Select

Flesh tone

Color Enhance

...

BRIGHTNESS

( ) : Adjusts screen brightness.

...

ACE

(Adaptive Clarity Enhancer)

: Selects the clarity mode.

Not applied

Weak clarity and luminosity contrast.

Strong clarity and luminosity contrast.

...

RCM(Real Color Management): Selects the color mode.

This is used for advertising in the store. The screen will

be divided to show the standard mode on the left and

video mode on the right so that the consumers can

check the difference after applying the video mode.

MENU : Exit

: Decrease

: Increase

SET : Select another sub-menu

To adjust the USER sub-menu

function, press the SET Button

Troubleshooting

No image appears

Check the following before calling for service.

No image appears

Do you see a "OSD LOCKED" message on the screen?

● Is the power cord of the

display connected?

● Is the power indicator

light on?

● Is the power on and the

power indicator blue or

green?

● Is the power indicator

amber or flickering

blue ?

● Do you see an "OUT

OF RANGE" message

on the screen?

● Do you see a "CHECK

SIGNAL CABLE"

message on the

screen?

•

Check and see if the power cord is connected

properly to the power outlet.

• Press

the Power button.

•

Adjust the brightness and the contrast.

•

If the display is in power saving mode, try moving

the mouse or pressing any key on the keyboard to

bring up the screen.

• Try to turn on the PC

•

This message appears when the signal from the

PC (video card) is out of horizontal or vertical

frequency range of the display. See the

'Specifications' section of this manual and

configure your display again.

•

This message appears when the signal cable

between your PC and your display is not

connected. Check the signal cable and try again.

• You can secure the current control settings,

so that they cannot be inadvertently changed.

You can unlock the OSD controls at any time

by pushing the MENU button for several

seconds: the message

“OSD UNLOCKED” will appear.

●

Do you see “OSD

LOCKED” when you

push MENU button?

Troubleshooting

Display image is incorrect

● Display Position is

incorrect.

● On the screen

background, vertical

bars or stripes are

visible.

● Any horizontal noise

appearing in any

image or characters

are not clearly

portrayed.

•

Press the AUTO/SET button to automatically

adjust your display image to the ideal setting.

If the results are unsatisfactory, adjust the image

position using the H position and V position icon

in the on screen display.

•

Press the AUTO/SET button to automatically

adjust your display image to the ideal setting.

If the results are unsatisfactory, decrease the

vertical bars or stripes using the CLOCK icon in

the on screen display.

•

Press the AUTO/SET button to automatically

adjust your display image to the ideal setting.

If the results are unsatisfactory, decrease the

horizontal bars using the PHASE icon in the on

screen display.

•

Check Control Panel --> Display --> Settings

and adjust the display to the recommended

resolution or adjust the display image to the ideal

setting. Set the color setting higher than 24 bits

(true color).

IMPORTANT

Check Control Panel --> Display --> Settings and see if the frequency or the

resolution were changed. If yes, readjust the video card to the recommend

resolution.

If the recommended resolution (optimal resolution) is not selected, letters may be

blurred and the screen may be dimmed, truncated or biased. Make sure to select

the recommend resolution.

The setting method can differ by computer and O/S (Operation System),

and resolution mentioned above may not be supported by the video card

performance. In this case, please ask to the computer or the video card

manufacturer.

Troubleshooting

Have you installed the display driver?

●

Have you installed the

display driver?

●

Do you see an

"Unrecognized monitor,

Plug&Play (VESA DDC)

monitor found"

message?

•

Be sure to install the display driver from the display

driver CD (or diskette) that comes with your

display. Or, you can also download the driver from

our web site: http://www.lge.com.

•

Make sure to check if the video card supports

Plug&Play function.

Display image is incorrect

● The screen color is

mono or abnormal.

● The screen blinks.

•

Check if the signal cable is properly connected

and use a screwdriver to fasten if necessary.

•

Make sure the video card is properly inserted in

the slot.

•

Set the color setting higher than 24 bits (true color)

at Control Panel - Settings.

•

Check if the screen is set to interlace mode and if

yes, change it to the recommend resolution.

Page is loading ...

LG LG W2294T-PF User manual

Brand: LG

Model: LG W2294T-PF

Category: TVs & monitors

Type: User manual

This manual is also suitable for

W2294T-PF

Download PDF

report

LG LG W2294T-PF User manual

This manual is also suitable for

LG LG W2294T-PF User manual

Related papers

Other documents