62937 Installation Instructions. Revision 1 September 2008
OUTSIDE MOUNTING
INSTALLATION STEPS
1. Position door for clear access to the end of the axle and drum.
2. Install L-Bracket and U-Bracket (pre-assembled with bearing) onto the main bracket with 4 sets of M12x35mm long set screws.
3. Place the motor onto the L-Bracket by guiding the 4 fi xed bolts through the slot holes at shown position and secured with 4xM10
nuts, washer and spring washers.
4. Slide the 6.4mm-keyed shaft into motor and place the 8mm key into the groove, slide steel sprocket onto the shaft and the shaft
through the bearing.
5. Secure shaft with the second external clip.
6. Align the 13 teeth steel sprocket with the above sprocket, tighten with grub screw.
7. Attach and link 10B steel chain around sprockets semi tight and adjust motor position by releasing the corresponding nuts so that
all parts rotate freely in operation.
8. Check tension of the 10B steel chain over its full rotation and if necessary realign steel sprocket concentric to the door drum axle.
2.
M12x35 BOLT 4 OFF
3.
M8x25 BOLT 2 OFF
5. E-CLIP
4.
6. 13 TEETH STEEL SPROCKET
7.
A
SEE DETAIL A
DISCLAIMER
THESE INSTRUCTIONS ARE INTENDED FOR PROFESSIONAL GARAGE DOOR INSTALLERS
and only apply to the fittings
Note: All references are taken from inside looking out
MARANTEC OPENER ON
ROLL-A-SHUTTER
INSTALLATION INSTRUCTIONS
Part No. 62692
Marantec Opener on Roll-A-Shutter Installation Instructions
INSIDE MOUNTING
NOTE
For opening height more than 3100mm inside mounting an adaptor plate with Part No. 62953 to be purchased.
INSTALLATION STEPS
1. Position door for clear access to the end of the axle and drum.
2. Fit Adaptor Plate to Main Bracket with 4 sets of M12x35.
3. Install L-Bracket and U-Bracket (pre-assembled with bearing) onto the Adaptor Plate with 4 sets of M12x25mm and 4 sets of
M12x35mm long set screws.
4. Place the motor onto the L-Bracket by guiding the 4 fi xed bolts through the slot holes at shown position and secured with 4xM10
nuts, washer and spring washers.
5. Slide the 6.4mm-keyed shaft into motor and place the 8mm key into the groove, slide steel sprocket onto the shaft and the shaft
through the bearing.
6. Secure shaft with the second external clip.
7. Align the 13 teeth steel sprocket with the above sprocket, tighten with grub screw.
8. Attach and link 10B steel chain around sprockets semi tight and adjust motor position by releasing the corresponding nuts so that
all parts rotate freely in operation.
9. Check tension of the 10B steel chain over its full rotation and if necessary realign steel sprocket concentric to the door drum axle.
8
150
300
14
47
R23
2.
M12x25 BOLT 4 OFF
M12x35 BOLT
4 OFF
3.
4.
8MM KEY
E-CLIP
OPTIONAL ADAPTOR PLATE FOR
RAS INSIDE MOUNT PART NO: 62953
62937 Installation Instructions. Revision 1 September 2008
B
SEE DETAIL B
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Ransomes 4390969 Owner's manual
-
Greenlee 555 Series, 555CX, 555DX Electric Benders User manual
-
-
Duncan Renovator MK1 Drill User manual
-
Abarth 500D Workshop Manual
-
Masport ROTARY MOWER Owner's manual
-
Royal Enfield Bullet Electra EFI User manual
-
Suzuki GN125F User manual
-
Buell XB9R 2003 User manual
-
Polaris HawkEye User manual
