Whirlpool AKR 803 IX Program Chart

Brand: Whirlpool

Model: AKR 803 IX

Category: Cooker hoods

Type: Program Chart

5019 318 33245 LI249A

INSTALLATIONSBLAD

Minsta tillåtna avstånd från olika typer av spisar: 50 cm från elektriska spisar, 70 cm från gasspisar

och kombinerade gas- och elspisar.

Om ett större avstånd än det här specificerade anges i installationsanvisningarna som medföljer

gasspisen är det detta avstånd som gäller.

Slå inte på strömmen till fläktkåpan förrän installationen är helt avslutad.

Produkt med hög vikt. För flyttning och installation av fläktkåpan krävs minst två personer.

INSTALLASJONSVEILEDNING

Minimumsavstand til komfyrtopp: 50 cm ved elektriske komfyrer, 70 cm ved gasskomfyr eller

kombinasjon.

Dersom installasjonsveiledningen for gassapparatet krever en større avstand enn den som er oppgitt,

må denne avstanden overholdes.

Apparatet må ikke tilkobles strømnettet før installasjonen er helt avsluttet.

Dette produktet er svært tungt. Flytting og installasjon av kjøkkenventilatoren må derfor utføres av

to eller flere personer.

INSTALLATIONSVEJLEDNING

Minimumafstand fra kogezoner: 50 cm for elkomfurer og 70 cm for gaskomfurer eller el-/

gaskomfurer.

Hvis installationsvejledningen for gaskogezonen/gaskomfuret angiver en afstand, der er større end

den anførte afstand, skal den største afstand overholdes.

Apparatet må ikke tilsluttes elforsyningen, før installationen er fuldført.

Produkt med meget stor vægt, flytning og montering af emhætten skal foretages af mindst to eller

flere personer.

ASENNUSOHJEET

Vähimmäisetäisyys liedestä: 50 cm sähkölevyistä, 70 cm kaasu- tai yhdistelmäliesistä.

Jos kaasulieden asennusohjeissa määrätään yllä mainittua etäisyyttä suurempi etäisyys, noudata sitä.

Älä kytke liesituuletinta sähköverkkoon ennen kuin kaikki asennusvaiheet on suoritettu.

Liesituuletin on painava, ja sen siirtämisessä ja asennuksessa tarvitaan vähintään kaksi henkilöä.

INSTALLATION SHEET

Minimum distance from burners: 50 cm for electric cookers, 70 cm for gas or combined cookers.

If the installation instructions for the gas cooker specify a greater distance, this must be taken into

account.

Do not connect the appliance to the power supply until installation has been completed.

Very heavy product; hood handling and installation must be carried out by at least two persons.

FIN

5019 318 33245 LI249A

FRONT

BACK

R1 ( )

FRONT

BACK

R1 ( )

FRONT

BACK

FRONT

3 x Ø 10 mm

3 x 6x70mm

6 x Ø 2,9x9,5

5 x Ø 3,5x6,5

I x 3

W x 3

3 x Ø10mm

max.40 W

(E14)

STOP!

c x 3

H (70cm)

H (50cm)

Xcm

Ycm

Lcm

L (@) = X-Y-H+3cm

FRAMSIDA - BAKSIDA

FORSIDE - BAKSIDE

FORSIDE - BAGSIDE

ETU - TAKA

FRONT - BACK

5019 318 33245 LI249A

FRONT

BACK

FRAMSIDA - BAKSIDA

FORSIDE - BAKSIDE

FORSIDE - BAGSIDE

ETU - TAKA

FRONT - BACK

FRONT

BACK

5019 318 33245 LI249A

ELECTRIC

SHOCK!

Safety screw

Säkerhetsskruv

Sikkerhetsskrue

Sikkerhedsskrue

Varmistusruuvi

Safety screw

5019 318 33245 LI249A

FRONT

Click!

FRONT

Click!

FRONT

FRAMSIDA

FORSIDE

ETU

FRONT

5019 318 33245 LI249A

DESCRIPTION OF HOOD

Aesthetic cap

Support bracket with cables and hooking brackets

Adjustment screw

Cover

Connection box

Cable clamp

Interconnection cable

Fitted hood (lights + motor assembly)

Control rod

Halogen lamp

Filter holder frame

Carbon filter (already fitted)

Grease filter (already fitted)

Filter holder frame

Fixing screws

Lighting unit of side lamps

Assembly template

Important!

The control rod is supplied with the appliance and must be installed last, before connecting the hood to the power

supply.

Insert the control rod in the special seat (see the diagrams on the first pages of this handbook - with release, compulsory coupling

direction).

3 x Ø 10 mm

3 x 6x70mm

6 x Ø 2,9x9,5

5 x Ø 3,5x6,5

I x 3

W x 3

max.40 W

(E14)

S DK FIN GB

5019 318 33245 LI249A

INSTALLATION - ASSEMBLY INSTRUCTIONS

The hood is designed for operation in filter version only:

Air is filtered through a carbon filter and recycled into the

surrounding environment.

The hood is provided with fixing plugs suitable for the majority of walls/ceilings. However, it is necessary to contact a qualified

technician to ascertain suitability of the materials according to the type of wall/ceiling. The wall/ceiling must be strong enough

to take the weight of the hood.

Disconnect the power supply at the main switch in the home during the electrical connection phases.

Fig.2

Place the template (supplied)

(Fig. 2) on the ceiling directly above the cooktop, matching the centre of the template (

)

with the centre of the cooktop (

The sides of the template must be parallel to the sides of the cooktop. Prepare the electrical connection.

Note:

The side of the template with the wording “

FRONT

” corresponds to the hood controls side.

Drill the holes indicated on the template, and insert the plugs.

Fig.3

Prepare the support bracket

, suitably adjusting the length of the cables according to the following formula:

L (cm)= X-36

L = truss extension

X = distance between the ceiling and the bottom edge of the hood

After finding the right length, secure the cables, tightening the lock nuts (

Fig. 3c

) with a spanner.

Important:

Respect the minimum distance from burners, indicated on the first page of the manual.

Fig.4

Apply the support bracket on the ceiling, passing the cables for the electrical connection through the middle hole.

Fix with 3 screws.

IMPORTANT! Detail B (support bracket) is equipped with a wire (yellow/green) which must be connected to the

earth of the household electrical system.

Fig.5

Fix the lighting unit to the hood with 3 screws and crescent-shaped washers.

Note:

The inside rim of the lighting unit has chamfers which must match the fixing places.

Fig.6

Apply the aesthetic cap

to cover the hood, passing the interconnection electrical cable inside.

Important:

Make sure the interconnection cable does not touch the lamps and arrange the excess part using the cable clamps

located at the top of the hood.

Fig.7

Fix the hood to the hooking brackets and secure with 1 screw for each bracket (COMPULSORY FIXING).

Fig.8

Adjust the position of the hood by means of the adjustment screws

Fig.9

Insert the control rod in the special seat.

Note!

Compulsory coupling direction, with release.

Fig.10

Fix the connection box

to the support bracket on the ceiling with 2 screws.

Carry out the electrical connection and secure the cables with the cable clamp

with 2 screws.

Fix the connection box cover with 4 screws.

Important!

Replacement of the interconnection cable must be carried out by the authorised after-sales technical service.

Fig.11

Insert the cover

between the support cables, making sure they enter the special slots on the cover.

Important!

Leave enough cable so that it passes easily through the slot obtained in the cover.

Secure the cover with 3 grub screws already screwed (or to be screwed) on the support bracket

Note:

The 3 fixing screws secure the cover by virtue of the friction they exert on the cover itself, and therefore must not be

completely tightened.

Fig.12

Apply the aesthetic tabs I (press-on) to cover the hood fixing rib points

S DK FIN GB

5019 318 33245 LI249A

PRODUCT SHEET

Control panel

Preliminary information for correct use of the hood:

Use the fastest speed in case of particularly concentrated cooking steam and fumes. It is advisable to switch the hood on 5

minutes before starting to cook and leave it running for another 15 minutes at the end of cooking.

The hood is equipped with a “

TOUCH SENSOR

” device able to determine when the control rod is touched by the user, thus

enabling control of lights and speeds. For this purpose, carefully read the following instructions.

Automatic switching on function

The hood is equipped with a temperature sensor that activates the motor at extraction speed (power) 1 when the ambient

temperature in the area surrounding the hood exceeds 70°C.

In any case intervention is possible, to switch off or change the extraction speed (power) (

refer to section “Extraction

speed (power) control”

Extraction speed (power) control

Extraction speed (power) selection is cyclic according to the speed sequence

therefore every time the

TOP PART

of the control rod is touched the extraction speed (power) increases by one level and

switches off (stand-by) if the rod is touched again when the hood is on extraction speed (power) 4

Note:

Extraction speed (power) 4 remains on for 5 minutes, after which the extraction motor switches to speed 2.

By touching the rod again the extraction motor switches off (Stand-by).

The hood can also be switched off (stand-by) when the hood is on any speed, by touching the

TOP PART

of the control rod

for more than 3 seconds.

The hood extraction speed (power) can be determined, since the rod is provided with a LED that changes colour according to

the extraction speed (power) as follows:

Hood on stand-by:

LED OFF

extraction speed (power) 1

- GREEN LED

extraction speed (power) 2

- ORANGE (amber) LED

extraction speed (power) 3

- RED LED

extraction speed (power) 4

- RED LED (FLASHING)

Top

part

Bottom

part

→

stand-by - 1

→

S DK FIN GB

5019 318 33245 LI249A

Grease filter cleaning required:

GREEN LED flashing (read the relevant instructions in “Reset and configuration of filter

saturation signalling”)

Carbon filter cleaning or changing required:

ORANGE (amber) LED flashing (read the relevant instructions in “Reset and

configuration of filter saturation signalling”)

Control of middle light

The middle light can be switched on or off by BRIEFLY touching the

BOTTOM PART

of the control rod.

Control of side lights (when provided)

The side lights can be switched on or off by PROLONGED touching of the

BOTTOM PART

of the control rod.

As well as switching on and off, PROLONGED TOUCHING allows adjustment of brightness of the lamps.

Note:

The switching on and off (and adjustment) functions alternate.

Reset and configuration of filter saturation signalling

Switch the hood on at any speed (refer to section “Extraction speed (power) control”)

Reset of grease filter saturation signalling (GREEN LED FLASHING on control rod)

Firstly carry out filter maintenance as described in the relevant section.

To u c h t h e

TOP PART

of the control rod for more than 3 seconds, the LED will stop flashing to indicate that signalling has been

reset, and the hood switches off.

Reset of carbon filter saturation signalling (ORANGE (amber) LED FLASHING)

Firstly carry out filter maintenance as described in the relevant section.

To u c h t h e

TOP PART

of the control rod for more than 3 seconds, the LED will stop flashing, indicating that signalling has been

reset, and the hood switches off.

Deactivation of carbon filter saturation signalling (for particular applications)

Switch off the hood (refer to section “Extraction speed (power) control”)

To u c h t h e

TOP PART

of the control rod for more than 5 seconds, the LED will flash GREEN (amber) indicating deactivation of

carbon filter saturation signalling.

To reactivate carbon filter saturation signalling, repeat the operation, and the LED will flash ORANGE.

S DK FIN GB

5019 318 33245 LI249A

Maintenance

ALWAYS disconnect the hood from the power supply.

Grease filter

It must be cleaned once a month (or when this need is

indicated by the filter saturation system - if provided for) with

non-aggressive detergents, by hand or in a dishwasher at low

temperatures and with short cycle.

Cleaning in a dishwasher may cause discolouring of the

grease filter, but its filtering efficiency is unaffected.

Carbon filter

It absorbs unpleasant odours produced during cooking.

The carbon filter can be washed every two months (or when

the filter saturation system indicates this need) in hot water

and with suitable detergents or in a dishwasher at 65°C

(when cleaning in a dishwasher, do a complete wash cycle

without any dishes).

Remove excess water without damaging the filter, then place

in the oven at 100°C for 10 minutes to dry it completely.

Replace the mat every 3 years or when the cloth is damaged.

Removing the filters

The metal grease filter and the carbon filter are installed

coupled at the bottom (extraction area).

To remove or refit them, proceed as follows:

Fig.11

a+c

. turn the three screws 1/4 turn.

b+d+e

. remove the filter holder frame and the metal grease

filter (and the carbon filter).

Proceed in reverse order to refit.

Replacing lamps

Disconnect the appliance from the power supply.

Caution!

Make sure lamps are cold before touching them.

Replacing the middle lamp: only use halogen lamps max. 40W

40° D25 GU10.

Removing the lamp:

twist 1/4 turn anticlockwise and remove.

To fit the lamp:

insert the lamp in the special seat so that its contacts enter

the seats on the lamp holder, and twist 1/4 turn (approx.)

clockwise.

Replacing the side lamps

Pull off the aesthetic cap upwards and unscrew the burnt-out

lamp; replace only with olive-shaped lamps 40Wmax. (E14)

Fig.11

S DK FIN GB

5019 318 33245 LI249A

SAFEGUARDING THE ENVIRONMENT

1. Packing

The packing materials are 100% recyclable and are marked with the

recycling symbol . Comply with local regulations for disposal. The

packing materials (plastic bags, polystyrene parts, etc.) are a potential

source of danger and must be kept out of the reach of children.

2. Product

This appliance is marked in compliance with European Directive

2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).

By ensuring that this appliance is correctly scrapped, the user can

help prevent potentially harmful consequences for the environment

and the health of people.

The symbol on the product or the accompanying documentation

indicates that it should not be treated as domestic waste but must be

taken to a suitable collection centre for the recycling of electrical and

electronic equipment.

Disposal must be carried out in compliance with local regulations on

waste disposal.

For further information on the treatment, recovery and recycling of this

product, contact the competent local office, the household waste

collection service or the shop where you purchased the appliance.

PRECAUTIONS AND GENERAL

RECOMMENDATIONS

IMPORTANT!

• The appliance is not intended for use by children or

people with limited physical, sensory or mental abilities or

without experience and knowledge of it, unless they are

supervised or instructed in its use by a person responsible

for their safety.

• Children must be supervised so that they do not play with

the appliance.

1. Do not connect the appliance to the mains power supply until

installation has been completed. Always disconnect the hood before

any cleaning or maintenance, by unplugging it or turning off the main

switch in the home.

2. Do not “flambé” food under the hood. Naked flames could cause a

fire.

3. Do not leave pans unattended when frying, since the cooking oil

could catch fire.

4. Regular cleaning and maintenance is essential for correct hood

operation and good performance. Regularly clean all deposits from

dirty surfaces. Regularly remove and clean or change the filter. Do

not use flammable materials to duct the extracted air.

5. If the hood is used together with other appliances operating on gas

or other fuels, the negative pressure in the room must not exceed

4Pa (4 x 10-5 bar). Therefore, make sure the room is adequately

ventilated.

6. The air extracted by the hood must not be removed through the

flue of the heating system or other appliances that use gas or other

fuels.

7. The room must be adequately ventilated when the hood is used

together with appliances operating on gas or other fuels.

8. Make sure lamps are cold before touching them.

9. The discharge air must not be ducted in a flue used for removing

fumes produced by appliances operating on gas or other fuels,

but must have a separate outlet.

All national regulations on air discharge must be observed.

10. The hood is not a shelf, therefore do not overload or place

objects on it.

11. Do not use or leave the hood without its lamps correctly

installed - risk of electric shock.

Note:

Always wear work gloves for all installation and maintenance

operations.

Electrical connection

The mains power supply must match the voltage given on the

dataplate located inside the hood. If provided with a plug, connect

the hood to a socket complying with current regulations and located

in an accessible area. If it does not have a plug (direct connection to

the power supply) or if the socket is not in an accessible place, fit a

suitable double-pole switch that ensures complete disconnection

from the power supply in category III overvoltage conditions,

complying with the installation rules.

IMPORTANT: Before reconnecting the hood circuit to the

power supply and checking correct operation, always make

sure the power cable is correctly fitted and that it was NOT

crushed in its housing during installation.

Cleaning the hood

Warning!

Failure to remove oil/grease (at least once a month) could

result in fire.

Use a soft cloth with a neutral detergent. Never use abrasive

substances or alcohol.

Before using the hood

To ensure best use of your hood, please read these instructions

carefully and keep them for future reference.

The packing materials (plastic bags, polystyrene parts, etc.) are a

potential source of danger and must be kept out of the reach of

children.

Make sure the hood was not damaged during transport.

Declaration of conformity

This product has been designed, manufactured and put on the

market in conformity with the following:

- safety objectives of "Low Voltage" Directive 73/23/EEC

- protection requirements of “EMC” Directive 89/336/EEC

amended by Directive 93/68/EEC.

Troubleshooting guide

The hood does not work:

• Is the plug properly inserted in the power socket?

• Is there a power failure?

The hood is not extracting enough:

• Is the right speed selected?

• Do the filters need cleaning or changing?

• Are the air outlets blocked?

The light does not work:

• Does the lamp need replacing?

• Is the lamp correctly fitted?

AFTER-SALES SERVICE

Before calling the After-Sales Service

1. See if you can eliminate the problem on your own (refer to

”Troubleshooting guide”).

2. Switch the hood off and then on again to check if the problem

has been eliminated.

3. If the problem persists, contact the After-Sales Service.

Specify:

•the type of fault,

• the product model given on the dataplate inside the hood, visible

on removing the grease filters.

• your full address,

• your telephone number and area code.

• the Service code (the number under the word SERVICE on the

dataplate inside the hood, behind the grease filter).

If any repairs are necessary, contact an authorised Service Centre (to

ensure the use of original spare parts and correct repair).

Failure to comply with these instructions can compromise the safety

and quality of the product.

S DK FIN GB

Whirlpool AKR 803 IX Program Chart

Brand: Whirlpool

Model: AKR 803 IX

Category: Cooker hoods

Type: Program Chart

Download PDF

report

in other languages

dansk: Whirlpool AKR 803 IX

Whirlpool AKR 803 IX Program Chart

Whirlpool AKR 803 IX Program Chart

in other languages

Related papers

Other documents