AlarmForce Industries SJLWS7315 User manual

Brand
AlarmForce Industries
Model
SJLWS7315
Type
User manual

This manual is also suitable for

1
W
W
a
a
t
t
e
e
r
r
S
S
e
e
n
n
s
s
o
o
r
r
(
(
W
W
S
S
-
-
7
7
3
3
1
1
5
5
M
M
H
H
Z
Z
)
)
Water Sensor is specially designed to detect if the water level is above a certain level
that may damage your protected goods. It is a device that helps to manage your
protected place and goods by keeping it nice and dry.
I
I
.
.
P
P
O
O
W
W
E
E
R
R
:
:
The WATER SENSOR uses 4 AAA alkaline batteries as its power source. The battery is good
for at least 5 years before it needs changing.
The WATER SENSOR will only detect the low battery (< 3.6V) when an alarm has been
activated. The low battery signal will be sent to the Control Panel along with the alarm signal
transmission for the Control Panel to display the status accordingly.
I
I
I
I
.
.
G
G
E
E
T
T
T
T
I
I
N
N
G
G
S
S
T
T
A
A
R
R
T
T
E
E
D
D
:
:
Step 1: Remove the cover by losing the two fixing screw on the top and bottom of
WATER SENSOR
Step 2: Insert 4 AAA alkaline batteries in the battery compartment
Step 3: Put the Control Panel into Learning Mode.
Step 4: Press the Test Button on the Water Sensor, and a radio signal will be
transmitted to the Control Panel for learning.
Step 5: Please refer to the panel’s manual for checking the panel’s response. If the water
sensor has not been learnt-in successfully, please repeat step 4 again.
Step 6: Put the Control Panel back to standby mode.
Step 7: The Learning-In process is now completed.
Test Button
2
I
I
I
I
I
I
.
.
M
M
O
O
U
U
N
N
T
T
I
I
N
N
G
G
W
W
A
A
T
T
E
E
R
R
S
S
E
E
N
N
S
S
O
O
R
R
:
:
The base has two knockouts, where the plastic is thinner for mounting purpose. To mount
the SW-7:
I. Remove the screw to separate the top cover from the base.
II. Break through the two knockouts on the base where the plastic is thinner.
III. Using the 2 knockouts on the base as a template, drill two holes in the
surface.
IV. Insert the wall plugs if fixing into plaster or brick
V. Clips the lid to the base
VI. Screw Water Sensor to the wall
VII. Locate the plastic clip and remove the cover from the adhesive pad
VIII. Fix the probes within the plastic clip and firmly press the clip onto the desired
location.
I
I
V
V
.
.
N
N
O
O
R
R
M
M
A
A
L
L
O
O
P
P
E
E
R
R
A
A
T
T
I
I
O
O
N
N
:
:
Mount the Water Sensor on the wall whereas drop the black wire onto the floor level or any
height that you want to detect the increasing water level.
z When the probes first come in contact with water, Water Sensor sends an alarm
signal to the control panel to notify the user.
<
<
N
N
O
O
T
T
E
E
>
>
) After Water Sensor enters Normal Operation Mode, please make sure to
wipe up the remnant water on the probes.
V. Supervisory Signal
z If the Control Panel has not received the signal from the Water Sensor for a preset
period of time, the Control Panel will indicate it on its display to show that particular
Water Sensor is experiencing an out-of-signal problem.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
FCC Caution :
To assure continued compliance, any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables
when connecting to computer or peripheral devices).
  • Page 1 1
  • Page 2 2

AlarmForce Industries SJLWS7315 User manual

Brand
AlarmForce Industries
Model
SJLWS7315
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents