Bafo BF-7312 User manual

BF-7312 USB 2.0 File Transfer Cable User’s Manual

1

USER’S MANUAL

BF-7312 USB 2.0 File Transfer Cable

1. Introduction

Congratulations on your purchase of BF-7312 USB 2.0 File Transfer Cable! The

PCLinq2 cable provides true plug-n-play capability while transferring files at greater

speed than traditional USB or other legacy port file transfer products. Hi-Speed USB

2.0 solutions offer up to 40 times the speed compared to normal full-speed USB 1.1

products.

PCLinq2 also provides a File Transfer program that is similar to Windows Program

Manager so you can easily drag-and-drop files or create folders in your local computer

or in the linked remote PC. Just plug in the cable, run the PCLinq2 program and

instantly transfer or copy files at high speed.

The PCLinq2 Hi-Speed USB Bridge Cable is highly suitable for mobile computer

use and SOHO environment.

2. Package Content

 Hardware: USB 2.0 File Transfer Cable

 Software: Driver software on CD

3. Product Features

 Suitable for Mobile PC and SOHO environment

 Single chip ASIC Hi-Speed USB host to host communication

 Dual data buffer supports two-way data transfer

 Hi-Speed Performance with data transfer rate of over 15Mbytes/sec

 Full Compliance with the Universal Serial Bus Specification v1.1 and v2.0

 Bus Powered from either USB port– no separate power required

 Advanced Power Management Mechanism includes Suspend-Resume and

Remote Wake0up Functions.

4. System Requirements

PC

 IBM

®

PC Pentium 133 or higher or compatible system

 Available USB 2.0 port or available USB1.1 port

 CD-ROM drive

 Windows

®

98, Windows

®

ME, Windows

®

2000 and Windows

®

XP

BF-7312 USB 2.0 File Transfer Cable User’s Manual 2

5. Driver Installation (PC to PC File Transfer)

Note:

If you plug the cable on a non-Hi-Speed USB port, Windows will show an alert

message telling you that it is plugged into a non-Hi-Speed USB hub. You can

still continue to use the BF-7312 USB 2.0 File Transfer Cable but it will run at a

reduced speed. Windows will recommend you to add a Hi-Speed USB host

controller to your computer to obtain maximum performance.

5.1 Windows

®

98 Driver Installation

5.1.1 Power on both computers and make sure USB port is enabled and

working properly.

5.1.2 Insert the driver of BF-7312 USB 2.0 File Transfer Cable into the CD-

ROM drive.

Select “Install Products - BF-7312 USB 2.0 File Transfer Cable -

Install”.

Attention: Don’t plug BF-7312 USB 2.0 File Transfer Cable into

PC’s USB Port when installing driver.

5.1.3 Click “Next” to continue.

BF-7312 USB 2.0 File Transfer Cable User’s Manual 3

5.1.4 Click “Finish” to end installation.

5.1.5 After installation, there will have a new “PClinq2 (ANSI)” icon at

desktop.

5.1.6 Please restart your computer.

5.1.7 When system operation success, you needed to be plug the BF-7312

USB 2.0 File Transfer Cable into USB Port of PC.

Windows

®

will detect an USB Device. Your new hardware is installed

and ready to use.

BF-7312 USB 2.0 File Transfer Cable User’s Manual 4

5.2 Windows

®

98 Driver Un-Installation

If you don’t want to use this cable and want to eternally delete this driver from

the PC then just follow the un-install procedure as following.

Attention: Before you go through the un-installation procedure, please

make sure that the BF-7312 USB 2.0 File Transfer Cable has been plug-off

from PC.

5.2.1 Insert the driver of BF-7312 USB 2.0 File Transfer Cable into the CD-

ROM drive.

Select “Install Products - BF-7312 USB 2.0 File Transfer Cable -

Install”.

5.2.2 Select the “OK” to uninstall.

5.2.3 Select the “Yes, I want to restart my computer now.” to uninstall,

then Click “OK” to end this un-installation procedure.

BF-7312 USB 2.0 File Transfer Cable User’s Manual 5

5.3 Windows

®

ME Driver Installation

5.3.1 Power on both computers and make sure USB port is enabled and

working properly.

5.3.2 Insert the driver of BF-7312 USB 2.0 File Transfer Cable into the CD-

ROM drive.

Select “Install Products - BF-7312 USB 2.0 File Transfer Cable -

Install”.

Attention: Don’t plug BF-7312 USB 2.0 File Transfer Cable into

PC’s USB Port when installing driver.

5.3.3 Click “Next” to continue.

5.3.4 Click “Finish” to end installation.

BF-7312 USB 2.0 File Transfer Cable User’s Manual 6

5.3.5 After installation, there will have a new “PClinq2 (ANSI)” icon at

desktop.

5.3.6 Plug the BF-7312 USB 2.0 File Transfer Cable into USB Port of PC.

Windows

®

will detect an USB Device. Your new hardware is installed

and ready to use.

BF-7312 USB 2.0 File Transfer Cable User’s Manual 7

5.4 Windows

®

ME Driver Un-Installation

If you don’t want to use this cable and want to eternally delete this driver from

the PC then just follow the un-install procedure as following.

Before you go through the un-installation procedure, please make sure

that the BF-7312 USB 2.0 File Transfer Cable has been plug-off from PC.

5.4.1 Insert the driver of BF-7312 USB 2.0 File Transfer Cable into the CD-

ROM drive.

Select “Install Products - BF-7312 USB 2.0 File Transfer Cable -

Install”.

5.4.2 Select the “OK” to uninstall.

5.4.3 Select the “Yes, I want to restart my computer now.” to uninstall,

then Click “OK” to end this un-installation procedure.

BF-7312 USB 2.0 File Transfer Cable User’s Manual 8

5.5 Windows

®

2000 Driver Installation

5.5.1 Power on both computers and make sure USB port is enabled and

working properly.

5.5.2 Insert the driver of BF-7312 USB 2.0 File Transfer Cable into the CD-

ROM drive.

Select “Install Products - BF-7312 USB 2.0 File Transfer Cable -

Install”.

Attention: Don’t plug BF-7312 USB 2.0 File Transfer Cable into

PC’s USB Port when installing driver.

5.5.3 Click “Next” to continue.

5.5.4 Click “Finish” to end installation.

BF-7312 USB 2.0 File Transfer Cable User’s Manual 9

5.5.5 After installation, there will have a new “PClinq2 (ANSI)” “PClinq2

(Unicode)” icon at desktop.

5.5.6 Plug the BF-7312 USB 2.0 File Transfer Cable into USB Port of PC.

Windows

®

will detect an USB Device and your new hardware is

installed and ready to use.

BF-7312 USB 2.0 File Transfer Cable User’s Manual 10

5.6 Windows

®

2000 Driver Un-Installation

If you don’t want to use this cable and want to eternally delete this driver from

the PC then just follow the un-install procedure as following.

Before you go through the un-installation procedure, please make sure

that the BF-7312 USB 2.0 File Transfer Cable has been plug-off from PC.

5.6.1 Insert the driver of BF-7312 USB 2.0 File Transfer Cable into the CD-

ROM drive.

Select “Install Products - BF-7312 USB 2.0 File Transfer Cable -

Install”.

5.6.2 Select the “OK” to uninstall.

5.6.3 Select the “Yes, I want to restart my computer now.” to uninstall,

then Click “OK” to end this un-installation procedure.

BF-7312 USB 2.0 File Transfer Cable User’s Manual 11

5.7 Windows

®

XP Driver Installation

5.7.1 Power on both computers and make sure USB port is enabled and

working properly.

5.7.2 Insert the driver of BF-7312 USB 2.0 File Transfer Cable into the CD-

ROM drive.

Select “Install Products - BF-7312 USB 2.0 File Transfer Cable -

Install”.

Attention: Don’t plug BF-7312 USB 2.0 File Transfer Cable into

PC’s USB Port when installing driver.

5.7.3 Click “Next” to continue.

5.7.4 Click “Finish” to end installation.

BF-7312 USB 2.0 File Transfer Cable User’s Manual 12

5.7.5 After installation, there will have a new “PClinq2 (ANSI)” “PClinq2

(Unicode)” icon at desktop.

5.7.6 Plug the BF-7312 USB 2.0 File Transfer Cable into USB Port of PC.

Windows

®

will detect an USB Device. Your new hardware is installed

and ready to use.

BF-7312 USB 2.0 File Transfer Cable User’s Manual 13

5.8 Windows

®

XP Driver Un-Installation

If you don’t want to use this cable and want to eternally delete this driver from

the PC then just follow the un-install procedure as following.

Before you go through the un-installation procedure, please make sure

that the BF-7312 USB 2.0 File Transfer Cable has been plug-off from PC.

5.8.1 Insert the driver of BF-7312 USB 2.0 File Transfer Cable into the CD-

ROM drive.

Select “Install Products - BF-7312 USB 2.0 File Transfer Cable -

Install”.

5.8.2 Select the “OK” to uninstall.

5.8.3 Select the “Yes, I want to restart my computer now.” to uninstall,

then Click “OK” to end this un-installation procedure.

BF-7312 USB 2.0 File Transfer Cable User’s Manual 14

6. Running the PClinq2 (ANSI) Application Program (PC to PC File Transfer)

Note:

The Unicode program is only supported in Windows 2000 and Windows XP. The

ANSI program is available for all Windows OS versions. Use the PCLinq2

Unicode version if both PCs have Windows 2000 or Windows XP.

6.1 Windows 98, ME, Windows 2000 & Windows XP

Follow the steps below on how to run the PClinq2 (ANSI) application program:

The step of use the application program are similar for four kinds of OS, we just

use Windows

®

2000 for an example.

6.1.1 Run Setup program on both (local and remote) computers.

6.1.2 Plug the one end of the PCLinq2 Hi-Speed USB Bridge cable into the

USB port of one computer and the other end into the USB port of the

other computer.

6.1.3 Wait for Windows to detect the cable on each computer and check if it

is properly installed.

BF-7312 USB 2.0 File Transfer Cable User’s Manual 15

6.1.4 Double-click on the PCLinq2 program. You can also click Start-

Programs-PCLinq2 High-Speed USB Bridge Cable to access the

PCLinq2 programs. It is important that you use the same program

mode for each computer. If you are using ANSI mode, then both

computers should be running the ANSI mode program. Check the

Status LED on the bottom right of the program dialog box if it is ready

or not. A green LED signifies a ready status while a red LED means

not ready or not found. Make sure that the program shows two green

LEDs to indicate a linked connection.

6.1.5 Once a connection has been established, you simply drag-and-drop

the files or folders you want to transfer to the other computer. You can

change disk drives or directories but clicking on the pull-down

directory menu. Use the File menu for other functions of the program.

BF-7312 USB 2.0 File Transfer Cable User’s Manual 16

6.1.6 You can cut, copy, paste, or drag files and folders between two

computers just like Windows

®

Explorer file manager.

7. FAQ

Q: How can I know two PC are successfully connected?

A: The bottom of the screen will show “Remote Connected” at both computers.

Q: Should I un-install the driver each time when the cable been plugged-off?

A: You don’t have to un-install driver each time when you plug this cable off.

Unless you don’t want to use this cable any more, then you could un-install it

and remove driver from your PC.

BF-7312 USB 2.0 File Transfer Cable User’s Manual 17

8. Disclaimer

Information in this document is subject to change without notice. The manufacturer

does not make any representations or warranties (implied or otherwise) regarding

the accuracy and completeness of this document and shall in no event be liable for

any loss of profit or any other commercial damage, including but not limited to

special, incidental, consequential, or other damages.

No part of this document may be reproduced or transmitted in any form by any

means, electronic or mechanical, including photocopying, recording or information

recording and retrieval systems without the express written permission of the

manufacturer.

All brand names and product names used in this document are trademarks, or

registered trademarks of their respective holders.

9. FCC Statement

This device generates and uses radio frequency and may cause interference to

radio and television reception if not installed and used properly. This has been

tested and found to comply with the limits of a Class B computing device in

accordance with the specifications in Part 15 of FCC Rules. These specifications

are designed to provide reasonable protection against such interference in a

residential installation. However, there is no guarantee that interference will not

occur in a particular installation. If this device does cause harmful interference to

radio or television reception, which can be determined by plugging the device in

and out, the user can try to correct the interference by one or more of the

followings:

 Reorient or relocate the receiving antenna.

 Increase the separation between the device and receiver.

 Connect the computer into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

Bafo BF-7312 User manual

Bafo BF-7312 User manual

Other documents