Hama 00050091 Owner's manual

Hama
Brand
Hama
Model
00050091
Category
Paper shredders
Type
Owner's manual

Hama 00050091 This device is a paper shredder with a cross-cut cutting style and a cutting capacity of 5 sheets of 70 g/m² paper at a time. It has a maximum feeding width of 220 mm and a cutting speed of 2.4 m/min. The shredder has an automatic start/stop function, as well as a reverse function to clear paper jams. It also has an overload protection function to prevent the motor from overheating. The shredder comes with a 2-year warranty.

Here are some possible use cases for the Hama 00050091 paper shredder:

  • Shredding confidential documents to protect your privacy
  • Shredding old bills and bank statements to reduce clutter

Hama 00050091 This device is a paper shredder with a cross-cut cutting style and a cutting capacity of 5 sheets of 70 g/m² paper at a time. It has a maximum feeding width of 220 mm and a cutting speed of 2.4 m/min. The shredder has an automatic start/stop function, as well as a reverse function to clear paper jams. It also has an overload protection function to prevent the motor from overheating. The shredder comes with a 2-year warranty.

Here are some possible use cases for the Hama 00050091 paper shredder:

  • Shredding confidential documents to protect your privacy
  • Shredding old bills and bank statements to reduce clutter
0 0050091/02.08
All listed brands are trademarks of the corresponding companies. Errors and omissions excepted,
and subject to technical changes. Our general terms of delivery and payment are applied.
Aktenvernichter »CC 612L«
Paper Shredder
Massicot
OFFICE
Hama GmbH & Co KG
D-86651 Monheim/Germany
www.hama.com
00050091
Page is loading ...
3
INSTALLATION:
1. Place the shredder on the rim of the waste paper basket.
2. Connect the power cable to a 220~240 V socket.
3. Set the switch to “AUTO”. If the green light does not
illuminate after doing this, reposition the shredder
correctly on the paper basket.
MODES:
Using the switch on the device, select one of the following
modes.
AUTO – On this setting, the shredder switches itself on
automatically as soon as you insert paper into the paper
feeder. It switches off automatically after there is no more
paper.
REV – In the unlikely case of paper being trapped in the cut-
ter, the reverse function allows you to remove the blockage.
OFF – This setting switches off the shredder.
SLITTING CAPACITY:
The CC 612L can shred up to 5 sheets of 70 g/m² paper with
a maximum width of 220 mm at the same time.
A FOLDED SHEET OF PAPER IS THE EQUIVALENT OF TWO
SHEETS!
WARNING:
1. Ensure you do not insert things such as clothes, ties,
jewellery or hair into the paper feeder.
2. Set the switch to “OFF” if you will not use the shredder
for a prolonged period of time.
3. Remove any paper clips and staples from the paper
before shredding. The shredder will not break if you
forget to do this once. However, you should normally
avoid this.
4. Keep hands and fi ngers away from the underside of the
shredder during operation and especially the cutting
roller, as this can cause serious injury.
5. The runtime of the shredder should not exceed two
minutes at a time. If you happen to have a large quantity
of paper to shred, we recommend that you switch off the
shredder after 2 minutes of continuous operation and
wait 15 minutes before switching the shredder back on
again.
6. The socket you use should be close to the shredder and
be easily accessible.
7. Always switch the shredder off (or remove the mains
plug) before moving or cleaning the shredder or
emptying the paper basket.
8. Empty the paper basket regularly.
PAPER BLOCKAGE AND OVERLOAD PREVENTION:
The CC 612L has a motor with an overload prevention
function. The normal operating cycle for uninterrupted
shredding activity is 2 minutes continuous operation follo-
wed by 15 minutes switched off. The shredder could switch
off automatically in the following situations:
1. If the shredder is used for more than two minutes at a
time.
2. If it becomes overloaded due to more than fi ve sheets of
paper being fed into the shredder at a time, or if the
paper is not fed into the shredder evenly.
Both cases could trigger the automatic overload prevention
function, which interrupts the power supply. If this is the
case, proceed as follows:
1. Remove the plug from the socket and wait at least 15
minutes until the overload prevention function resets.
Remove all remaining paper from the shredder or cut it
off in an appropriate way.
2. Connect the machine to the mains again and set the
switch to “REV”. Using the reverse function, feed the
paper trapped in the cutting roller out of the top of the
shredder. You can then set the switch back to “AUTO”.
3. If the switch is set to “AUTO” and the paper feeder is
clear, the shredder is now ready to use again.
SPECIFICATIONS:
• Cutting size: 4x39 mm (cross cut)
• Cutting capacity: 5 sheets
• Cutting speed: 2.4 m/min.
• Max. feeding width: 220 mm
• Mains supply: 220~240 V
• Measurements of the CC 612L: 380x160x360 mm
g
Operating Instructions
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Hama 00050091 Owner's manual

Hama
Brand
Hama
Model
00050091
Category
Paper shredders
Type
Owner's manual

Hama 00050091 This device is a paper shredder with a cross-cut cutting style and a cutting capacity of 5 sheets of 70 g/m² paper at a time. It has a maximum feeding width of 220 mm and a cutting speed of 2.4 m/min. The shredder has an automatic start/stop function, as well as a reverse function to clear paper jams. It also has an overload protection function to prevent the motor from overheating. The shredder comes with a 2-year warranty.

Here are some possible use cases for the Hama 00050091 paper shredder:

  • Shredding confidential documents to protect your privacy
  • Shredding old bills and bank statements to reduce clutter
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents