Havis C-CB-LOCK Datasheet

Havis
Brand
Havis
Model
C-CB-LOCK
Category
Car kits
Type
Datasheet

Havis C-CB-LOCK is a lock option for the Combo Box Series that provides an additional layer of security for your valuables. The lock is easy to install and comes with all the necessary hardware. The lock features a tumbler mechanism that is keyed alike, so you can use the same key to lock all of your Combo Boxes. The lock arm bracket can be bent to ensure a proper fit and engagement with the lock catch bracket. The Havis C-CB-LOCK is a great way to keep your valuables safe and secure.

Havis C-CB-LOCK is a lock option for the Combo Box Series that provides an additional layer of security for your valuables. The lock is easy to install and comes with all the necessary hardware. The lock features a tumbler mechanism that is keyed alike, so you can use the same key to lock all of your Combo Boxes. The lock arm bracket can be bent to ensure a proper fit and engagement with the lock catch bracket. The Havis C-CB-LOCK is a great way to keep your valuables safe and secure.

C-CB-LOCK_INST_6-09.docx6-09
Installation Instructions
C-CB-LOCK
Lock Option For Combo Box Series
Warning: Please read all instructions prior to installation of the armrest lock.
TOOLS REQUIRED:
Phillips Screw Driver
Adjustable Wrench
HARDWARE: (Supplied in Kit)
Qty. Description Qty. Description
1 Lock Assembly Kit 2 #8-32 PEM Studs
1 Lock Arm Bracket 2 #8-32 Hex Nuts
1 Lock Catch Bracket
INSTALLATION:
1. Remove Armrest Pad:
Remove the four screws that attach
the armrest pad, and set the pad
aside. Keep all of the hardware, as
the pad will need to be reattached
to complete installation.
2. Attach Lock Catch Bracket to Inside of Armrest:
Place the two #8-32 PEM studs
through the two holes provided,
and hold in place. The two PEM
studs do not need to be crimped.
Place the Lock Catch Bracket onto
the two PEM studs in the
orientation shown, and secure with
two #8-32 hex nuts.
Remove
and save
these four
screws and
washers.
#8-32 hex
nuts
#8-32 PEM
studs
Lock catch
bracket
C-CB-LOCK_INST_6-09.docx6-09
3. Remove Knockout From Panel:
Remove the plastic knockout from
the panel side hole.
Verify that the alignment notch is
oriented exactly as shown. If it is
not, rotate and/or flip over the
panel to match this orientation.
4. Assemble Lock:
Lay out all pieces to the lock
assembly as shown in the picture.
Note that the Lock Assembly Kit
may include additional hardware
not pictured; any such hardware is
not needed.
Insert the Mounting Shell into the
panel hole, and place the Trim
Ring on the inside of the panel as a
washer. Secure with the Mounting
Shell Nut.
Insert the Tumbler into the
Mounting Shell, noting the
orientation of the key.
Place the Lock Arm Bracket onto
the Tumbler, orienting it to be
horizontal when unlocked and
vertical when locked, and noting
the orientation of the catch.
Secure with the Locknut and
Screw.
5. Finish and Test:
The assembled lock should look as
pictured. Test for correct
operation. Note that the Lock Arm
Bracket may need to be bent to
correctly engage the Lock Catch
Bracket.
Re-attach the armrest pad removed
during Step 1.
Keys
Tumbler
Mounting Shell
Trim Ring
Mounting Shell Nut
Lock Arm Bracket
Locknut
Screw
Remove
knockout
plug. Ensure
notch is
oriented as
shown.
  • Page 1 1
  • Page 2 2

Havis C-CB-LOCK Datasheet

Havis
Brand
Havis
Model
C-CB-LOCK
Category
Car kits
Type
Datasheet

Havis C-CB-LOCK is a lock option for the Combo Box Series that provides an additional layer of security for your valuables. The lock is easy to install and comes with all the necessary hardware. The lock features a tumbler mechanism that is keyed alike, so you can use the same key to lock all of your Combo Boxes. The lock arm bracket can be bent to ensure a proper fit and engagement with the lock catch bracket. The Havis C-CB-LOCK is a great way to keep your valuables safe and secure.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents