ALDER TAPWARE Vito Bertoni QAAD SINK MIXER Installation guide

Brand
ALDER TAPWARE
Model
Vito Bertoni QAAD SINK MIXER
Type
Installation guide
For all servicing needs, please contact CUSTOMER SERVICE on:
FREECALL: 1800 800 919 PHONE: 08 6217 0600 FAX: 08 6217 0699 EMAIL: customer.service@aldertapware.com.au
www.aldertapware.com.au www.vitobertoni.com.au
V02 160520
alder tapware
PRODUCT: QAAD SINK MIXER
WARRANTY
1. Warranty claims must be accompanied by the invoice showing dates of purchase or installation. Where a product
has not been installed, the product can be returned with proof of purchase, to the place of purchase.
2. This warranty may become void due to the following:-
• Inability to provide proof of purchase
• Products not installed by a licensed plumber
• Products not installed in accordance with installation instructions
• Products exposed to pressures that exceed 500 Kpa and or temperatures that exceed 75oC within a building
– Refer AS/NZS 3500.1:2003 (Clause 3.34)
• Damage to ceramic disc cartridges from foreign matter e.g. sand, dirt, stones, thread tape, pieces of copper
or plastic tubing etc.
• Inadequate flushing of system prior to usage, causing damage and/or obstructions to the product
• Damage to product surface due to installation (including adhesives and sealants) or post-installation
• Failure to install flow regulators and check valves from outlets including showers, sink and vegie mixers
• Products not used for its intended purpose
• Products fitted with other devices to the outlet e.g. water filters
• Failure to observe care and cleaning instructions, including failure to regularly clean aerator inserts in taps
and or shower heads
35mm Cartridge
For all servicing needs, please contact CUSTOMER SERVICE on:
FREECALL: 1800 800 919 PHONE: 08 6217 0600 FAX: 08 6217 0699 EMAIL: customer.service@aldertapware.com.au
www.aldertapware.com.au www.vitobertoni.com.au
V02 160520
INSTALLATION
This set up will allow:
1. Left hand operation is recommended, however there is a choice of
installation positions to suit your needs – left, right or center.
2. Cold setting when lever is at vertical position when installed.
Your Mixer comes fully assembled.
For installation follow steps below:
1. Flush out all pipe work before installation of the mixer
2. Figure 3 - Screw in M8 fixing stud (4) to underside of body and remove the
locknut (5).
3. Push on base square ring (1)
4. Screw in flexible connectors (6) – blue markings to the cold and red
markings for the hot.
5. Feed flexible connectors through mounting hole in sink/deck/counter
6. From underneath, install / fit horseshoe rubber washer (2), horseshoe
fixing plate (3) and locknut (5)
7. Use a tube spanner to tighten mixer to sink.
8. Connect hot & cold flexible connectors to supply inlets.
NOTE:
Flexible connectors must not be kinked, stretched, twisted or in tension
when fitted.
Flexible connectors must not be installed with a curvature radius of no
less than 6 times the outside diameter.
Ensure hoses are not exposed to abrasive or corrosive agents or a naked
flame.
Hoses must be inspected regularly for signs of corrosion to the stainless
braid and replaced immediately if sighted.
FIG 2
FIG 3
FIG 1
  • Page 1 1
  • Page 2 2

ALDER TAPWARE Vito Bertoni QAAD SINK MIXER Installation guide

Brand
ALDER TAPWARE
Model
Vito Bertoni QAAD SINK MIXER
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents