dji Phantom 1 Operating instructions

Brand: dji

Model: Phantom 1

Type: Operating instructions

This manual is also suitable for

The DJI Phantom 1 drone offers a range of capabilities for aerial photography and videography. Equipped with a 3-axis gimbal, it provides stable and smooth footage, while its GPS system enables precise positioning and stable hovering. The Phantom 1 also features a compact and lightweight design, making it easy to transport and operate. The 12-megapixel camera captures high-quality images and videos, making it suitable for both professional and recreational use. Additionally, its long flight time allows for extended shooting sessions.

P330CB-H3-2D Instruction V1.00

P330CB-H3-2D Board is designed to replace the center board inside the PHANTOM. P330CB-H3-2D has

integrated PMU(Power manage unit) and GCU(Gimbal control unit)，and has added ports for wireless video

transmission module and Zenmuse H3-2D to enhance the compatibility with H3-2D.

For NAZA-M Firmware version V3.12 or above，Assistant software version V2.12 or above.

Introduction

To battery

Note: only

3S battery

is allowed

GPS port, Connect

GPS module with

GPS cable

To X3 port on MC

To EXP port on MC

Installation

position for MC

Reserved

Connect to

wireless video

transmitter with a

3pin cable

Connect to 8pin

port on H3-2D

Gimbal with an

8pin cable

wireless

video

transmitter

Signal

VCC

GND

In the box

P330CB-H3-2D Board(1), LED Board(1), 8pin cable(1), 3pin cable(1), 3M Fixing pad(1)

Spare screws: Phillips-head screws M2.0*6.5(5) and M1.6*4(3)

Self-prepared tools

Allen screw driver, Phillips-head screw driver, soldering iron, cable ties, scissors

Assembly steps

1、Disassemble the 4 propellers of the PHANTOM.（Disassemble 4 prop guards too if they are assembled）

2、Remove screws on 4 arms to open the top cover of PHANTOM. Below shows the positions of screws to be

removed on one arm.

Fig.1 Screws to be removed

3、Disassemble the original center board inside the PHANTOM

（1）Cut off the cable ties to release the USB cable fixing to the center board.（A1）

（2）Disconnect the connections with the MC.(B1-B2)

（3）Desolder the ESC cables(C1-C4) connected to the center board.

（4）Remove the screws(D1-D4)to disassemble the original center board.

Fig.2 Disassemble items

To M4 port on MC

To LED port on MC

To M1 port on MC

To M3 port on MC

To GPS port on

P330CB-H3-2D

To X2 port on MC

To M2 port on MC

Fig.3 Original center board is disassembled

4、Disassemble the original LED Board, assemble the new LED Board

LED Shell

Screws

LED

Board

Fig.4 Replace the LED Board

5、Assemble P330CB-H3-2D

（1）Remove the MC from the original center board and assemble the MC on P330CB-H3-2D Board with 3M

fixing pad, make sure the MC is assembled in the direction shown below.

（2）Assemble the P330CB-H3-2D Board with screws(D1-D4).

（3）Solder the ESC cables to the P330CB-H3-2D Board as VCC to V and GND to G.

（4）Connect the cables to the MC then tidy and check the final connections.

Fig.5 Assemble and solder

Push off the white

soft plug, then

make the 8pin

cable thread the

hole on the

bottom board of

M2 arm

Connect to

wireless

video

transmitter

Connect the

8pin cable to

the 8pin port

on the gimbal

before you

mount the

Damping unit

and gimbal

Fig.6 Final connections

6、Reassemble the covers and propellers, please make sure the cover points to the right nose

direction and the rotating marks on propellers are in accordance with the marks on the cover.

dji Phantom 1 Operating instructions

Brand: dji

Model: Phantom 1

Type: Operating instructions

This manual is also suitable for

Download PDF

report

dji Phantom 1 Operating instructions

This manual is also suitable for

dji Phantom 1 Operating instructions

Related papers

Other documents