Cascade E Series Installation guide

Cascade
Brand
Cascade
Model
E Series
Type
Installation guide
Installation
Instructions
E-Series Push/Pull and
Carpet Pole Removal
and Installation
c
This sheet provides instructions to remove and install
Cascade Push/Pull and Carpet Pole attachments. Refer to
specific service, installation and operator guides for proper
handling procedures and guidelines.
cascade
姞
corporation
Position pole
on a block
Carpet Pole Removal and Installation
WARNING: Keep hands and feet away from
pinch points and under the attachment.
For Technical Support . . . To Order Parts . . .
Call: 1-800-227-2233 Fax: 1-888-329-8207 Call: 1-888-227-2233 Fax: 1-888-329-0234
Internet: www.cascorp.com Internet: www.cascorp.com
Write: Cascade Corporation, PO Box 20187, Portland, OR 97294 Write: Cascade Corporation, 2501 Sheridan Ave., Springfield, OH 45505
AC0666.ill
AC0665.ill
AC0664.ill
Hook Guide
5/8 in.
(16 mm)
3/16 in.
(5 mm)
maximum
Raise lower hooks after
placing on truck carriage.
Install pins in upper holes.
4
4
2
1
Check lower
hook gap
Disconnect
lower hooks.
Center on truck carriage.
Engage upper hook centering
tab in carriage center notch.
1 Lower the attachment onto a pallet. Place the pole on a
block.
2 Disconnect the Quick-Change lower hooks. Pull out the
retaining pins, slide the lower hooks down and install the
retaining pins in the lower hook holes.
3 Lower the truck carriage and back away from the
attachment.
4 For installation, reverse the above procedures except for
the following items:
• Make sure the center locating tab in the upper hook
properly engages the center notch in the upper truck
carriage bar.
• The gap between the lower hook and carriage bar
must not exceed 3/16 in. (5 mm). If gap is excessive,
remove the hook guides and turn them over. Tighten
the capscrews to a torque of 118-125 ft.-lbs.
(160-170 Nm).
•Slide lower hooks up and install retaining pins in the
hook top holes to secure carpet pole on carriage.
NOTE: Install retaining pins
in the lower hook holes.
c
a
s
c
a
d
e
c
a
s
c
a
d
e
AC0769.ill
© Cascade Corporation 2003 3-2003 Part No. 6029046-R1
Push/Pull Removal and Installation
1
Fully extend the faceplate. Lower the attachment onto a
pallet. Position the lower hooks over the edge of the
pallet to allow the hooks to slide down.
2 Disconnect the Quick-Change lower hooks. Pull out the
retaining pins, slide the hooks down and install the pins
in the hook lower holes.
3 Disconnect and tag the hoses at the carriage hose
terminal.
4 Lower the truck carriage and back away from the
attachment.
5 For installation, reverse the above procedures except for
the following items:
• Make sure the center locating tab in the upper hook
properly engages the center notch in the upper truck
carriage bar.
• The gap between lower hook and carriage bar must
not exceed 3/16 in. (5 mm). If gap is excessive,
remove the hook guides and turn them over. Tighten
the capscrews to a torque of 118-125 ft.-lbs.
(160-170 Nm).
•Slide lower hooks up and install the
retaining pins in the top holes to
secure the attachment on the
carriage.
WARNING: Before removing hoses, relieve
pressure in the hydraulic system. Turn the
truck off, then open the truck auxiliary valve(s)
several times in both directions.
PP0863.ill
PP0864.ill
PP0865.ill
PP0866.ill
WARNING: Keep hands and feet away from
pinch points and under the attachment.
Center on truck carriage.
Engage upper hook
centering tab in carriage
center notch.
5
Hook Guide
5/8 in.
(16 mm)
3/16 in.
(5 mm)
maximum
Raise lower hooks
after placing on
truck carriage
5
Check lower
hook gap
3
Disconnect and
tag hoses
Position attachment
on a pallet
2
1
Disconnect
lower hooks
c
a
s
c
a
d
e
c
a
s
c
a
d
e
AC0769.ill
NOTE: Install retaining pins
in the lower hook holes.
  • Page 1 1
  • Page 2 2

Cascade E Series Installation guide

Cascade
Brand
Cascade
Model
E Series
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents