740170_INS_Indoor/Outdoor Digital Thermometer
Size:5”Wx4.75”H_Output:100%_Prints:1/1,Blk
Indoor/Outdoor
Digital Thermometer
TEMPERATURE AND
HUMIDITY AT A GLANCE
1
TABLE OF CONTENTS
Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Location of Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Battery Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Choosing In/Out Temp Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Temp and Humidity Alert Pre-Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Setting Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Max/Min Temp & Humidity Recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Comfort Level Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Other Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
2
740170_INS_Indoor/Outdoor Digital Thermometer
Size:5”Wx4.75”H_Output:100%_Prints:1/1,Blk
BATTERY PRECAUTIONS
• Dispose of the old batteries properly. Do not dispose of the old batteries
in a fire.
• Do not leave the batteries where a child or pet could play with or swallow
them. If the batteries are swallowed, contact a physician immediately.
• The batteries may explode if mistreated. Do not attempt to recharge or
disassemble the batteries.
• Use only fresh batteries of the required size and type. Do not mix old and
new batteries, different types of batteries, or rechargeable batteries of
different capacities.
CAUTION
1. The device should be used in the suggested operation environment.
DO NOT apply the device to extreme force, shock, high temperature,
water, AC power or severe weather conditions.
2. DO NOT attempt to dismantle the device’s internal components.
There are no serviceable parts inside.
3. The normal function of the device may be disturbed by strong electromagnetic
interference. If this occurs, simply reset the device to resume normal operation.
3
LOCATION OF PARTS AND CONTROLS
1. LCD Screen
2. In•Out Button
3. Alert Button
4. Max•Min Button
5. Clear Button
6. Sensor Tip with Adhesive
Pad and Screw-hole
7. Sensor
7
1
2
3
4
5
6
4
740170_INS_Indoor/Outdoor Digital Thermometer
Size:5”Wx4.75”H_Output:100%_Prints:1/1,Blk
LOCATION OF PARTS AND CONTROLS
1. Hanging Hole
2. Stand
3. Battery
Compartment Cover
4. ºC/ºF Switch
5. Battery Compartment
6. Sensor Wire Access
7. Sensor Jack
8. +/- Buttons
9. Reset Button
1
9
8
6
2
4
5
7
3
5
BATTERY INSTALLATION
1. Slide the BATTERY COMPARTMENT door to open and remove.
2. Insert 2 AAA batteries according to the polarity indicators inside
the compartment.
3. Replace and slide the BATTERY COMPARTMENT door closed to secure.
OPERATION
CONNECTING THE OUTDOOR SENSOR
1. Slide the BATTERY COMPARTMENT door to open and remove.
2. Plug the OUTDOOR SENSOR’s wire into the SENSOR JACK inside
the BATTERY COMPARTMENT and run it through the SENSOR ACCESS slot.
3. Replace and slide the BATTERY COMPARTMENT door closed to secure.
PLACING THE SENSOR
Finding a suitable location to mount the OUTDOOR SENSOR improves the accuracy
of readings and the reliability and durability of the device. The ideal location would be
on the north side of a building (south side in the southern hemisphere).
1. Remove the SENSOR TIP from the SENSOR and place by using the double-
stick ADHESIVE PAD, or by screwing the SENSOR TIP to the chosen location.
Important: Make sure it's within reach of the SENSOR WIRE.
2. Reinsert the SENSOR into the SENSOR TIP after placement.
6
740170_INS_Indoor/Outdoor Digital Thermometer
Size:5”Wx4.75”H_Output:100%_Prints:1/1,Blk
Note: When choosing a location for the OUTDOOR SENSOR, take into
consideration the objects nearby. Objects that heat up in direct sunlight or
produce radiative cooling effects may affect temperature readings by changing
the air temperature around the sensor. See the tips below for proper placement.
• Place the OUTDOOR SENSOR in a location where it will not be in direct
sunlight and where it will have limited exposure to reflected sunlight.
• Place the OUTDOOR SENSOR at least 5 feet from man-made sources
of heat.
• Place the OUTDOOR SENSOR in a location at least 10 feet from lights
and exhaust fans.
• Keep the OUTDOOR SENSOR and the cable at least 10 feet from
110V AC or 60Hz utility power.
• Do not run the OUTDOOR SENSOR cable parallel to house wiring.
• Mount the OUTDOOR SENSOR at least 30 feet from high-voltage
power lines and transformers.
CHOOSING IN/OUT TEMP MEASUREMENTS
Press the IN•OUT button. When the IN icon appears on the screen, it indicates
the indoor temperature is being displayed. When the OUT icon appears, it indicates
the outdoor temperature is being displayed.
Press the IN•OUT button to toggle between locations.
Note: When testing temperatures lower than -58°F, “LL.L” will appear on the
temperature display area; when testing temperatures higher than 230°F, “HH.H”
will be displayed.
As there is no humidity sensor for outdoor mode, the indoor humidity will
continue to appear on the humidity display area of the lower half of the screen
in outdoor mode.
7
TEMP/HUMIDITY ALERT PRE-SETTINGS
Alerts will tell you when the temperature or humidity is above or below a set
number. To view the alert pre-settings, press and release the ALERT button.
The IN or OUT icon will flash on the display to indicate which pre-setting is showing.
The pre-setting will be presented in the following order:
Indoor High Temperature > Indoor Low Temperature > Indoor High Humidity >
Indoor Low Humidity > Outdoor High Temperature > Outdoor Low Temperature >
and then it reverts back to the normal test mode.
8
9
SETTING ALERTS
1. Press and release the ALERT button repeatedly until the desired channel
(e.g., Indoor High Temperature) is visible on the display.
2. Press and hold the ALERT button for 2 seconds. The present reading will flash.
Inside the BATTERY COMPARTMENT, press the “+” or “—” buttons to increase/
decrease the alert setting to the desired number.
3. When the desired number is showing, press the ALERT button to confirm the
setting. Press any other button or wait for 20 seconds to cancel setting.
4. While in the alert setting mode (the corresponding IN/OUT icon will be blinking)
press the “+” or “—” button inside the BATTERY COMPARTMENT to activate or
deactivate the alert mode. The icon ((
•)) appears on the upper left of the LCD
display when alert mode is currently activated.
Note: You may also turn on the global alert mode by pressing the “+” button
while the unit is currently in alert mode (icon ((•)) is visible in the upper left
of the LCD display).
5. When alert mode is active and alert temperature and humidity are achieved,
an audible alert (beep) will sound. Press any button to deactivate.
Notes:
• The default pre-setting (after batteries are installed) of the low temperature
is -58°F, and the high setting is 230°F.
• The user setting(s), according to above indications, will be saved until the
next battery re-installation or the RESET button is pressed.
• The ((•)) icon can be set for each specific measurement (e.g., outside high
temperature). The ((•)) icon must be on for your setting to sound an alert.
10
740170_INS_Indoor/Outdoor Digital Thermometer
Size:5”Wx4.75”H_Output:100%_Prints:1/1,Blk
MAX/MIN TEMP & HUMIDITY RECORDING
1. The maximum/minimum temperature and indoor humidity is
recorded automatically.
2. Press the IN•OUT button to select the desired channel.
3. Press the MAX•MIN button to read the maximum/minimum temperature
and humidity. The MAX/MIN will display for 5 seconds, then revert to
current levels.
4. Press the CLEAR button once to reset the records of the displaying
MAX or MIN.
COMFORT LEVEL INDICATION
The device will indicate the indoor COMFORT/WET/DRY level on the screen
in the following situations:
Level Indicator Indoor Temp Range Indoor Humidity Range
Comfort 68ºF~77ºF/20ºC~25ºC 40% RH~70% RH
Wet At any temperature Over 70% RH
Dry At any temperature Below 40% RH
(Blank)
Over 77ºF (25ºC) or
below 68ºF (20ºC)
40% RH ~ 70% RH
11
OTHER ICONS
Normally, when temperature is within 32°F~140°F and the relative humidity is
20% RH~99% RH, the measurements will be displayed. If any temperature
is out of this range, other icons listed below will be shown:
1. “--%”: If the humidity area of the display shows “--% (IN)”, it means the measured
temperature is lower than 32°F or higher than 140°F, or the measured humidity
is out of the defined measuring range or lower than 1% RH. When the ambient
conditions resume normal operation range, the humidity area of the display will
show the correct humidity accordingly. Relative humidity measurement will be
affected by temperature.
2. “HH.H(IN)” or “HH.H(OUT)”: When the measured temperature is higher
than 230°F, these icons will appear in the temperature display area.
3. “LL.L(IN)” or “LL.L(OUT)”: When the measured temperature is lower
than -58°F, these icons will appear in the temperature display area.
4. “--.-(out)”: This icon will appear in the temperature display area if the sensor
cable is not well connected while measuring the outdoor temperature.
RESET
If the device malfunctions or you want to clear all settings, use a thin, blunt
object to press the RESET button inside the BATTERY COMPARTMENT.
Pressing RESET will revert the unit to its original default settings plus
clear any alerts set.
12
740170_INS_Indoor/Outdoor Digital Thermometer
Size:5”Wx4.75”H_Output:100%_Prints:1/1,Blk
SPECIFICATIONS
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AAA Batteries
OPERATIONAL ENVIRONMENT
Temperature Range
Indoor . . . . . . . . 32°F~122°F
Outdoor . . . . . . .-58°F—230°F
Humidity Range
Indoor . . . . . . . . 20%—99% RH
Outdoor . . . . . . .N/A
Note: Although the sensor can work within a wider temperature range
of -58°F~230°F, the LCD materials can work only within 32°F~122°F.
The above specifications are the results of comprehensive testing.
ONE (1) YEAR LIMITED WARRANTY
Brookstone
®
warrants this product against defects in materials and/or workmanship
under normal use for a period of ONE (1) YEAR from the date of purchase by the
original purchaser (“Warranty Period”). If a defect arises and a valid claim is received
within the Warranty Period, at its option, Brookstone will either 1) repair the defect
at no charge, using new or refurbished replacement parts, or 2) replace the product
with a new product that is at least functionally equivalent to the original product, or
3) provide a store credit in the amount of the purchase price of the original product.
A replacement product or part, including a user-installable part installed in accordance
with instructions provided by Brookstone, assumes the remaining warranty of the
original product. When a product or part is exchanged, any replacement item becomes
your property and the replaced item becomes Brookstone’s property. When a store
credit is given, the original product must be returned to Brookstone and becomes
Brookstone’s property.
Obtaining Service: To obtain warranty service, call Brookstone Limited Warranty Service
at 1-800-292-9819. Please be prepared to describe the product that needs service
and the nature of the problem. A purchase receipt is required. All repairs and
replacements must be authorized in advance. Service options, parts availability and
response times will vary. You are responsible for delivery and the cost of delivery of
the product or any parts to the authorized service center for replacement, per our
instructions.
Limits and Exclusions: Coverage under this Limited Warranty is limited to the United
States of America, including the District of Columbia and the U.S. Territories of
Guam, Puerto Rico, and the U.S. Virgin Islands. This Limited Warranty applies only
to products manufactured for Brookstone that can be identified by the “Brookstone”
trademark, trade name, or logo affixed to them or their packaging. The Limited
Warranty does not apply to any non-Brookstone products. Manufacturers or
13
suppliers other than Brookstone may provide their own warranties to the purchaser,
but Brookstone, in so far as permitted by law, provides these products “as is.”
This warranty does not apply to: a) damage caused by failure to follow instructions
relating to product’s use or the installation of components; b) damage caused by
accident, abuse, misuse, fire, floods, earthquake or other external causes; c) damage
caused by service performed by anyone who is not a representative of Brookstone;
d) accessories used in conjunction with a covered product; e) a product or part
that has been modified to alter functionality or capability; f) items intended to be
periodically replaced by the purchaser during the normal life of the product including,
without limitation, batteries or light bulbs; g) any product sold “as is” including, without
limitation, floor demonstration models and refurbished items; or h) a product that is
used commercially or for a commercial purpose.
BROOKSTONE SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING
OUT OF ANY BREACH OF THIS WARRANTY. TO THE EXTENT PERMITTED BY
APPLICABLE LAW, BROOKSTONE DISCLAIMS ANY AND ALL STATUTORY OR
IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
WARRANTIES AGAINST HIDDEN OR LATENT DEFECTS. IF BROOKSTONE
CANNOT LAWFULLY DISCLAIM STATUTORY OR IMPLIED WARRANTIES, THEN
TO THE EXTENT PERMITTED BY LAW, ALL SUCH WARRANTIES SHALL BE
LIMITED IN DURATION TO THE DURATION OF THIS EXPRESS WARRANTY.
Some states disallow the exclusion or limitation of incidental or consequential damages
or how long an implied warranty lasts, so the above exclusions or limitations may not
apply to you. This warranty gives you specific legal rights and you may also have other
rights, which vary from state to state.
14
740170_INS_Indoor/Outdoor Digital Thermometer
Size:5”Wx4.75”H_Output:100%_Prints:1/1,Blk
740170
Find thousands more
great ideas online
Merrimack, New Hampshire USA 03054 • 800-846-3000 • Brookstone.com
/