Moen DN7060 Installation guide

Type
Installation guide

Moen DN7060, your new tool-free shower chair, offers a safe and comfortable bathing experience. Made from durable materials like ABS plastic, aluminum, EPDM, and stainless steel, it can support up to 300 pounds. The adjustable legs with locking studs allow you to customize the seat height for your needs. Simply depress the stud, adjust the leg, and ensure the stud clicks into place. The easy-to-assemble seat back securely snaps onto the seat bottom. Remember, always follow the instructions and consult a healthcare professional for specific advice before use.

Moen DN7060, your new tool-free shower chair, offers a safe and comfortable bathing experience. Made from durable materials like ABS plastic, aluminum, EPDM, and stainless steel, it can support up to 300 pounds. The adjustable legs with locking studs allow you to customize the seat height for your needs. Simply depress the stud, adjust the leg, and ensure the stud clicks into place. The easy-to-assemble seat back securely snaps onto the seat bottom. Remember, always follow the instructions and consult a healthcare professional for specific advice before use.

Tool-Free Shower Chair is made of
ABS Plastic, Aluminum, EPDM, and
Stainless.
Warning:
TO PREVENT SRIOUS OR FATAL INJURY:
Insure product is assembled, adjusted and used
properly. FOR USE ONLY BY PERSONS
WEIGHING LESS THAN 300 POUNDS. Failure
to follow correct assembly and/or adjustment
procedures can make the seat unstable. ALL
FOUR LEGS MUST BE LOCKED IN PLACE AT
THE SAME HEIGHT. DO NOT jump on, stand
on or tilt. Contact CSI immediately at 1-800-882-
0116 if any components are missing or
damaged. Do not modify or substitute any
components. FOR QUESTIONS OR
ASSISTANCE WITH ASSEMBLY CONTACT
CSI AT 1-800-882-9116. Consult healthcare
professional for advice and instructions specific
to user’s needs before use.
DN7060 Tool-Free Shower Chair
White
1. Slide adjustable legs onto ends of under seat supports, being
careful to make sure that the single hole in the top of adjustable
leg aligns with the rounded brass studs on the under seat
supports.
2. Depress brass stud with thumb to allow adjustable leg to slide over
it. Brass stud will click into place through hole in adjustable leg.
To adjust length of adjustable legs:
1. To adjust length of adjustable legs/height of seat, depress stud to
allow leg to move in out of outer post, aligning stud with the hole in
post that corresponds with the desired length of adjustable leg.
Make sure that stud clicks into place at desired length.
2. Test each leg to make sure that all studs have fully clicked into
place.
3. Grasp seat back by handle and insert bottom tabs into large holes
in seat bottom until the tabs snap into place.
Stock Number:_________________ TF Shower Chair
By Creative Specialties
Materials:
Installation Instructions:
Stock Numbers:
Dimensions:
DN7060
Home Care Technical Specification
25300 AL MOEN DRIVE NORTH OLMSTED, OH 44070
CORPORATE HEADQUARTERS: (800) 321-8809 FAX: (800) 848-6636
INTERNATIONAL: (440) 962-2000 FAX: (440) 962-2726
CUSTOMER SERVICE (USA): 800-882-0116 FAX: (888) 379-2720
WWW.MOEN.COM
Copyright Creative Specialties International
Literature #BA1371
  • Page 1 1

Moen DN7060 Installation guide

Type
Installation guide

Moen DN7060, your new tool-free shower chair, offers a safe and comfortable bathing experience. Made from durable materials like ABS plastic, aluminum, EPDM, and stainless steel, it can support up to 300 pounds. The adjustable legs with locking studs allow you to customize the seat height for your needs. Simply depress the stud, adjust the leg, and ensure the stud clicks into place. The easy-to-assemble seat back securely snaps onto the seat bottom. Remember, always follow the instructions and consult a healthcare professional for specific advice before use.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI