Hifonics BRX316.4 Owner's manual

Hifonics
Brand
Hifonics
Model
BRX316.4
Type
Owner's manual

Hifonics BRX316.4 is a high-performance car amplifier designed to provide superior audio quality and power to your vehicle's sound system. With its compact design and advanced features, the BRX316.4 is an excellent choice for a wide range of applications.

The BRX316.4 features a 4-channel design, providing ample power to drive multiple speakers or subwoofers. It delivers 160 watts RMS per channel at 4 ohms, and 320 watts RMS per channel at 2 ohms. The amplifier also has a built-in crossover, allowing you to tailor the sound to your specific preferences. The variable low-pass filter (35Hz-300Hz) and variable high-pass filter (35Hz-2.5kHz) provide precise control over the frequency range of the output signal.

Hifonics BRX316.4 is a high-performance car amplifier designed to provide superior audio quality and power to your vehicle's sound system. With its compact design and advanced features, the BRX316.4 is an excellent choice for a wide range of applications.

The BRX316.4 features a 4-channel design, providing ample power to drive multiple speakers or subwoofers. It delivers 160 watts RMS per channel at 4 ohms, and 320 watts RMS per channel at 2 ohms. The amplifier also has a built-in crossover, allowing you to tailor the sound to your specific preferences. The variable low-pass filter (35Hz-300Hz) and variable high-pass filter (35Hz-2.5kHz) provide precise control over the frequency range of the output signal.

Place terminal in a secure
position so that it won’t
accidentally contact the
negative battery post
Power cable size
and fusing
It is critical to use the proper power
and ground cable. Select the size
listed here for your amplier model.
Always use high quality copper
cable. Visit our website for multi amp
system cable recommendations.
Be sure to use the proper fuse size
for each model. Some models require
an external fuse.
Properly route power,
speaker and RCA cables
through the vehicle.
Choose a mounting location
that will provide adequate air
ventilation. Mount the amplier to
a secure surface. Do not mount
the amplier upside down.
Attach the chassis ground
cable to the amplier
negative terminal. It is
important to make sure this
connection is very tight.
Bare metal
Attach the main power cable
to the amplier +12V. The
cable must run directly to
the battery and be properly
fused and be very tight.
Attach the remote turn on
wire to the amplier remote
output of the source unit.
Connect the RCA cables to
the INPUT connectors. The
OUTPUT can be used to
provide input for a second
amplier.
Connect the power cable to the
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
terminal.
Re-connect the negative
battery terminal making sure it
is securely tightened.
Connect the speaker cables to
the speaker output connectors.
Follow the diagram below
that best ts your speaker
conguration.
The chassis ground connection
is critical to the performance
of the amplier. Choose a
location that is close to the
amplier. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Disconnect
negative battery
terminal
Run Cables
Mount Amplier
Negative Power
Connection
Positive Power
Connection
Remote Turn-on
Connection
Signal Input
Connection
Positive Battery
Connection
Re-connect
Negative Battery
Terminal
Speaker
Connections
Chassis Ground
Be prepared to disarm your vehicle’s alarm and
to enter your radio / source unit code.
Stereo
Installation
Before you start
Monoblock
single woofer Monoblock multiple woofers
Bridged
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
1
2
3
5
7
6
8
11
12
104
Turn the LEVEL control completely
counter-clockwise to minimum.
Level Control
9
9V 0.2V
INPUT
LEVEL
6V 0.2V
INPUT
LEVEL
PHASE
0 180
BASS EQ
0 10dB
BASS EQ
0 9dB
15 35Hz
SUBSONIC
10 40Hz
SUBSONIC
30 250Hz
LPF
35 250Hz
LPF
40 300Hz
LPF
FULL
LP
HP
XOVER
MONO STEREO
MODE
FULL
LPF
HPF
XOVER
MONO STEREO
MODE
4CH 2CH
MODE
60 1.3KHz
HPF
60 1.2KHz
HPF
4ga
2ga
Model Fuse Size Cable Size
BRX316.4
BRX616.4
BRX1616.4
BRX5016.5
BRX1116.1D
BRX1516.1D
BRX2016.1D
BRX2416.1D
BRX3016.1D
BRX4016.1D
2-25A atc
2-30A atc
2-60A Maxi
ext - 200A
1-60A Maxi
2-70A Maxi
ext - 200A
ext - 225A
ext - 250A
ext
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER
CH 1
CH 2
BRIDGED
CH 3
CH 4
BRIDGED
OUTPUT
SPEAKER OUTPUT
CH 3
CH 4
BRIDGED
SPEAKER OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER
CH 1
CH 2
BRIDGED
CH 3
CH 4
BRIDGED
OUTPUT
SPEAKER OUTPUT
CH 3
CH 4
BRIDGED
SPEAKER OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER
CH 1
CH 2
BRIDGED
CH 3
CH 4
BRIDGED
OUTPUT
SPEAKER OUTPUT
CH 3
CH 4
BRIDGED
SPEAKER OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER
CH 1
CH 2
BRIDGED
CH 3
CH 4
BRIDGED
OUTPUT
SPEAKER OUTPUT
CH 3
CH 4
BRIDGED
SPEAKER OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
Hifonics products are designed and engineered in the USA by
www.maxxsonics.com
Setup Common System Setup
Quick Start
Installation Guide
The input MODE switch will “sum” or
combine the right and left channel signals
in the MONO position to improve bass
performance. Select MONO only when the
amp is being used for subwoofers.
The XOVER Mode switch sets the type
of crossover that will be active. 4 channel
models will have two switches, one for each
set of channels.
The HPF(high pass lter) control will limit the
output below the selected frequency. This
is typically used to protect midrange and hi
frequency speakers from damage and to
allow a smooth transition from a subwoofer.
The LPF(low pass lter) control will limit
output above the selected frequency. This
is used to allow a smooth transition to the
higher frequency speakers.
1. If possible, with the source unit off, conrm that the primary volume control is
turned down (counter clockwise).
2. Turn on the source unit (CD, or MP3 player). Re-conrm that the volume is
turned down. Make sure the source unit controls; balance, fader, bass and
treble are all set to center or “0” adjustment. Make sure that the green LED on
the end of the amplier is illuminated.
3. Play a clean musical selection of which you are very familiar. CD is preferred.
Do not use radio signals for level setting. Hit play and start turning the volume
of the source unit up.
4. Stop increasing the source unit volume when you reach 3/4 (about 75%) or until
you hear speakers begin to slightly start producing distortion.
5. Increase the amplier level (clockwise) until distortion is heard, then back
the level down (counter clockwise) until the distortion is eliminated. Small
adjustments may need to be made to balance the levels of multiple ampliers.
The Bass EQ control will increase the power
output at 45Hz for more pronounced bass.
Exercise caution when using this control.
Increase the level in small amounts until
distortion is noticed, then back off a little.
Some models include a bass
remote. Avoid adjusting the bass
remote while operating vehicle.
Input Mode
Xover Mode
High pass
Adjustment
Low pass
Adjustment
Bass Boost
Remote Level
Control
2ch - Full Range
4ch - Full Range
4ch - Mixed Mono
Mono
A
B
C
D
E
F
This is a critical step to insure your amplier
is properly adjusted to match the signal
output level of your source unit.
THIS IS NOT A VOLUME CONTROL!
Level Setting
G
WARRANTY
Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from
defects in material and workmanship for a period of one (1) year from the date of purchase.
Maxxsonics USA Inc. will, at it’s discretion, repair or replace defective products during the warranty
period. Components that prove to be defective in materials and workmanship under proper installation
and use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was
purchased. A photocopy of the original receipt must accompany the product being returned. The
costs associated with removal, re-installation and freight are not the responsibility of Maxxsonics
USA Inc. This warranty is limited to defective parts and specically excludes any incidental or
consequential damages connected therewith. To view the full warranty, please visit the website.
The information contained within this document is intended to offer some basic guidelines
for a few of the most common installations. More complex audio systems should be
installed by a competent professional. Additional installation information available at
www.maxxsonics.com
BRX316.4
BRX616 .4
BRX1616.4
BRX5016.5
BRX1116.1D
BRX1516.1D
BRX2016.1D
BRX2416.1D
BRX3016.1D
BRX4016.1D
9V 0.2V
INPUT
LEVEL
6V 0.2V
INPUT
LEVEL
PHASE
0 180
BASS EQ
0 10dB
BASS EQ
0 9dB
15 35Hz
SUBSONIC
10 40Hz
SUBSONIC
30 250Hz
LPF
35 250Hz
LPF
40 300Hz
LPF
FULL
LP
HP
XOVER
MONO STEREO
MODE
FULL
LPF
HPF
XOVER
MONO STEREO
MODE
4CH 2CH
MODE
60 1.3KHz
HPF
60 1.2KHz
HPF
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER
CH 1
CH 2
BRIDGED
CH 3
CH 4
BRIDGED
OUTPUT
SPEAKER OUTPUT
CH 3
CH 4
BRIDGED
SPEAKER OUTPUT
SPEAKER
LEFT
RIGHT
BRIDGED
OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
30 2.5K
LPF
35 250Hz
LPF
15 35Hz
SUBSONIC
FULL
LP
HP
XOVER
FULL
LP/BPHP
XOVER
MONO STEREO
MODE
10 2.5K
HPF
30 2.5K
LPF
FULL
LP/BPHP
XOVER
10 2.5K
HPF
30 2.5K
LPF
FULL
LP/BPHP
XOVER
10 2.5K
HPF
30 2.5K
LPF
FULL
LP/BPHP
XOVER
10 2.5K
HPF
CH 1/2
CH 3/4
CH 1/2
CH 3/4
30 2.5K
LPF
35 250Hz
LPF
15 35Hz
SUBSONIC
FULL
LP
HP
XOVER
FULL
LP/BPHP
XOVER
MONO STEREO
MODE
10 2.5K
HPF
30 2.5K
LPF
FULL
LP/BPHP
XOVER
10 2.5K
HPF
30 2.5K
LPF
FULL
LP/BPHP
XOVER
10 2.5K
HPF
30 2.5K
LPF
FULL
LP/BPHP
XOVER
10 2.5K
HPF
CH 1/2
CH 3/4
CH 1/2
CH 3/4
30 2.5K
LPF
35 250Hz
LPF
15 35Hz
SUBSONIC
FULL
LP
HP
XOVER
FULL
LP/BPHP
XOVER
MONO STEREO
MODE
10 2.5K
HPF
30 2.5K
LPF
FULL
LP/BPHP
XOVER
10 2.5K
HPF
30 2.5K
LPF
FULL
LP/BPHP
XOVER
10 2.5K
HPF
30 2.5K
LPF
FULL
LP/BPHP
XOVER
10 2.5K
HPF
CH 1/2
CH 3/4
CH 1/2
CH 3/4
30 2.5K
LPF
35 250Hz
LPF
15 35Hz
SUBSONIC
FULL
LP
HP
XOVER
FULL
LP/BPHP
XOVER
MONO STEREO
MODE
10 2.5K
HPF
30 2.5K
LPF
FULL
LP/BPHP
XOVER
10 2.5K
HPF
30 2.5K
LPF
FULL
LP/BPHP
XOVER
10 2.5K
HPF
30 2.5K
LPF
FULL
LP/BPHP
XOVER
10 2.5K
HPF
CH 1/2
CH 3/4
CH 1/2
CH 3/4
Congratulations on your choice of a Hifonics amplier.
This “Quick Start Installation” guide is meant to help you
“hook up” and play music. For more detailed information,
on system setting, speaker and subwoofer conguration
and full specications by model visit the website,
http://hifonics.com/manuals.html
HF BRX2015 QSG 01 - rev2
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER
CH 1
CH 2
BRIDGED
CH 3
CH 4
BRIDGED
OUTPUT
SPEAKER OUTPUT
CH 3
CH 4
BRIDGED
SPEAKER OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER
CH 3
CH 4
BRIDGED
OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER
CH 1
CH 2
BRIDGED
CH 3
CH 4
BRIDGED
OUTPUT
SPEAKER OUTPUT
CH 3
CH 4
BRIDGED
SPEAKER OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
CH 3
CH 4
BRIDGED
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER
CH 1
CH 2
BRIDGED
CH 3
CH 4
BRIDGED
OUTPUT
SPEAKER OUTPUT
CH 3
CH 4
BRIDGED
SPEAKER OUTPUT
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT
9V 0.2V
INPUT
LEVEL
6V 0.2V
INPUT
LEVEL
PHASE
0 180
BASS EQ
0 10dB
BASS EQ
0 9dB
15 35Hz
SUBSONIC
10 40Hz
SUBSONIC
30 250Hz
LPF
35 250Hz
LPF
40 300Hz
LPF
FULL
LP
HP
XOVER
MONO STEREO
MODE
FULL
LPF
HPF
XOVER
MONO STEREO
MODE
4CH 2CH
MODE
60 1.3KHz
HPF
60 1.2KHz
HPF
9V 0.2V
INPUT
LEVEL
6V 0.2V
INPUT
LEVEL
PHASE
0 180
BASS EQ
0 10dB
BASS EQ
0 9dB
15 35Hz
SUBSONIC
10 40Hz
SUBSONIC
30 250Hz
LPF
35 250Hz
LPF
40 300Hz
LPF
FULL
LP
HP
XOVER
MONO STEREO
MODE
FULL
LPF
HPF
XOVER
MONO STEREO
MODE
4CH 2CH
MODE
60 1.3KHz
HPF
60 1.2KHz
HPF
9V 0.2V
INPUT
LEVEL
6V 0.2V
INPUT
LEVEL
PHASE
0 180
BASS EQ
0 10dB
BASS EQ
0 9dB
15 35Hz
SUBSONIC
10 40Hz
SUBSONIC
30 250Hz
LPF
35 250Hz
LPF
40 300Hz
LPF
FULL
LP
HP
XOVER
MONO STEREO
MODE
FULL
LPF
HPF
XOVER
MONO STEREO
MODE
4CH 2CH
MODE
60 1.3KHz
HPF
60 1.2KHz
HPF
9V 0.2V
INPUT
LEVEL
6V 0.2V
INPUT
LEVEL
PHASE
0 180
BASS EQ
0 10dB
BASS EQ
0 9dB
15 35Hz
SUBSONIC
10 40Hz
SUBSONIC
30 250Hz
LPF
35 250Hz
LPF
40 300Hz
LPF
FULL
LP
HP
XOVER
MONO STEREO
MODE
FULL
LPF
HPF
XOVER
MONO STEREO
MODE
4CH 2CH
MODE
60 1.3KHz
HPF
60 1.2KHz
HPF
30Hz 1.5Hz
LPF
40Hz 300Hz
LPF
  • Page 1 1
  • Page 2 2

Hifonics BRX316.4 Owner's manual

Hifonics
Brand
Hifonics
Model
BRX316.4
Type
Owner's manual

Hifonics BRX316.4 is a high-performance car amplifier designed to provide superior audio quality and power to your vehicle's sound system. With its compact design and advanced features, the BRX316.4 is an excellent choice for a wide range of applications.

The BRX316.4 features a 4-channel design, providing ample power to drive multiple speakers or subwoofers. It delivers 160 watts RMS per channel at 4 ohms, and 320 watts RMS per channel at 2 ohms. The amplifier also has a built-in crossover, allowing you to tailor the sound to your specific preferences. The variable low-pass filter (35Hz-300Hz) and variable high-pass filter (35Hz-2.5kHz) provide precise control over the frequency range of the output signal.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents